April 2014 Itanium processor specification update:

http://www.intel.com/content/www/us/en/processors/itanium/itanium-specification-update.html

describes this erratum:

=========================================================================
237. Under a complex set of conditions, store to load forwarding for a
sub 8-byte load may complete incorrectly

Problem: A load instruction may complete incorrectly when a code sequence
using 4-byte or smaller load and store operations to the same address
is executed in combination with specific timing of all the following
concurrent conditions: store to load forwarding, alignment checking
enabled, a mis-predicted branch, and complex cache utilization activity.

Implication: The affected sub 8-byte instruction may complete
incorrectly resulting in unpredictable system behavior. There is an
extremely low probability of exposure due to the significant number of
complex microarchitectural concurrent conditions required to encounter
the erratum.

Workaround: Set PSR.ac = 0 to completely avoid the erratum. Disabling
Hyper-Threading will significantly reduce exposure to the conditions
that contribute to encountering the erratum.

Status: See the Summary Table of Changes for the affected steppings.
=========================================================================

[Table of changes essentially lists all models from McKinley to Tukwila]

The PSR.ac bit controls whether the processor will always generate
an unaligned reference trap (0x5a00) for a misaligned data access
(when PSR.ac=1) or if it will let the access succeed when running
on a cpu that implements logic to handle some unaligned accesses.

Way back in 2008 in commit b704882e
  [IA64] Rationalize kernel mode alignment checking
we made the decision to always enable strict checking. We were
already doing so in trap/interrupt context because the common
preamble code set this bit - but the rest of supervisor code
(and by inheritance user code) ran with PSR.ac=0.

We now reverse that decision and set PSR.ac=0 everywhere in the
kernel (also inherited by user processes). This will avoid the
erratum using the method described in the Itanium specification
update.  Net effect for users is that the processor will handle
unaligned access when it can (typically with a tiny performance
bubble in the pipeline ... but much less invasive than taking a
trap and having the OS perform the access).
Signed-off-by: NTony Luck <tony.luck@intel.com>

Pull parisc updates from Helge Deller:
 - revert parts of the latest patch regarding font selection with STICON
   console
 - wire up the utimes() syscall for parisc
 - remove the unused parisc tmpalias code and unnecessary arch*relax
   defines

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: locks: remove redundant arch_*_relax operations
  parisc: wire up sys_utimes
  parisc: Remove unused CONFIG_PARISC_TMPALIAS code
  partly revert commit 8a10bc9d: parisc/sti_console: prefer Linux fonts over built-in ROM fonts

Pull sparc fixes from David Miller:

 1) Do serial locking in a way that makes things clear that these are
    IRQ spinlocks.

 2) Conversion to generic idle loop broke first generation Niagara
    machines, need to have %pil interrupts enabled during cpu yield
    hypervisor call.

 3) Do not use magic constants for iterations over tsb tables, from Doug
    Wilson.

 4) Fix erroneous truncation of 64-bit system call return values to
    32-bit.  From Dave Kleikamp.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Make sure %pil interrupts are enabled during hypervisor yield.
  sparc64:tsb.c:use array size macro rather than number
  sparc64: don't treat 64-bit syscall return codes as 32-bit
  sparc: serial: Clean up the locking for -rt

Pull networking fixes from David Miller:

 1) OpenVswitch's lookup_datapath() returns error pointers, so don't
    check against NULL.  From Jiri Pirko.

 2) pfkey_compile_policy() code path tries to do a GFP_KERNEL allocation
    under RCU locks, fix by using GFP_ATOMIC when necessary.  From
    Nikolay Aleksandrov.

 3) phy_suspend() indirectly passes uninitialized data into the ethtool
    get wake-on-land implementations.  Fix from Sebastian Hesselbarth.

 4) CPSW driver unregisters CPTS twice, fix from Benedikt Spranger.

 5) If SKB allocation of reply packet fails, vxlan's arp_reduce() defers
    a NULL pointer.  Fix from David Stevens.

 6) IPV6 neigh handling in vxlan doesn't validate the destination
    address properly, and it builds a packet with the src and dst
    reversed.  Fix also from David Stevens.

 7) Fix spinlock recursion during subscription failures in TIPC stack,
    from Erik Hugne.

 8) Revert buggy conversion of davinci_emac to devm_request_irq, from
    Chrstian Riesch.

 9) Wrong flags passed into forwarding database netlink notifications,
    from Nicolas Dichtel.

10) The netpoll neighbour soliciation handler checks wrong ethertype,
    needs to be ETH_P_IPV6 rather than ETH_P_ARP.  Fix from Li RongQing.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
  tipc: fix spinlock recursion bug for failed subscriptions
  vxlan: fix nonfunctional neigh_reduce()
  net: davinci_emac: Fix rollback of emac_dev_open()
  net: davinci_emac: Replace devm_request_irq with request_irq
  netpoll: fix the skb check in pkt_is_ns
  net: micrel : ks8851-ml: add vdd-supply support
  ip6mr: fix mfc notification flags
  ipmr: fix mfc notification flags
  rtnetlink: fix fdb notification flags
  tcp: syncookies: do not use getnstimeofday()
  netlink: fix setsockopt in mmap examples in documentation
  openvswitch: Correctly report flow used times for first 5 minutes after boot.
  via-rhine: Disable device in error path
  ATHEROS-ATL1E: Convert iounmap to pci_iounmap
  vxlan: fix potential NULL dereference in arp_reduce()
  cnic: Update version to 2.5.20 and copyright year.
  cnic,bnx2i,bnx2fc: Fix inconsistent use of page size
  cnic: Use proper ulp_ops for per device operations.
  net: cdc_ncm: fix control message ordering
  ipv6: ip6_append_data_mtu do not handle the mtu of the second fragment properly
  ...

If a topology event subscription fails for any reason, such as out
of memory, max number reached or because we received an invalid
request the correct behavior is to terminate the subscribers
connection to the topology server. This is currently broken and
produces the following oops:

[27.953662] tipc: Subscription rejected, illegal request
[27.955329] BUG: spinlock recursion on CPU#1, kworker/u4:0/6
[27.957066]  lock: 0xffff88003c67f408, .magic: dead4ead, .owner: kworker/u4:0/6, .owner_cpu: 1
[27.958054] CPU: 1 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.0-rc6+ #5
[27.960230] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[27.960874] Workqueue: tipc_rcv tipc_recv_work [tipc]
[27.961430]  ffff88003c67f408 ffff88003de27c18 ffffffff815c0207 ffff88003de1c050
[27.962292]  ffff88003de27c38 ffffffff815beec5 ffff88003c67f408 ffffffff817f0a8a
[27.963152]  ffff88003de27c58 ffffffff815beeeb ffff88003c67f408 ffffffffa0013520
[27.964023] Call Trace:
[27.964292]  [<ffffffff815c0207>] dump_stack+0x45/0x56
[27.964874]  [<ffffffff815beec5>] spin_dump+0x8c/0x91
[27.965420]  [<ffffffff815beeeb>] spin_bug+0x21/0x26
[27.965995]  [<ffffffff81083df6>] do_raw_spin_lock+0x116/0x140
[27.966631]  [<ffffffff815c6215>] _raw_spin_lock_bh+0x15/0x20
[27.967256]  [<ffffffffa0008540>] subscr_conn_shutdown_event+0x20/0xa0 [tipc]
[27.968051]  [<ffffffffa000fde4>] tipc_close_conn+0xa4/0xb0 [tipc]
[27.968722]  [<ffffffffa00101ba>] tipc_conn_terminate+0x1a/0x30 [tipc]
[27.969436]  [<ffffffffa00089a2>] subscr_conn_msg_event+0x1f2/0x2f0 [tipc]
[27.970209]  [<ffffffffa0010000>] tipc_receive_from_sock+0x90/0xf0 [tipc]
[27.970972]  [<ffffffffa000fa79>] tipc_recv_work+0x29/0x50 [tipc]
[27.971633]  [<ffffffff8105dbf5>] process_one_work+0x165/0x3e0
[27.972267]  [<ffffffff8105e869>] worker_thread+0x119/0x3a0
[27.972896]  [<ffffffff8105e750>] ? manage_workers.isra.25+0x2a0/0x2a0
[27.973622]  [<ffffffff810648af>] kthread+0xdf/0x100
[27.974168]  [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0
[27.974893]  [<ffffffff815ce13c>] ret_from_fork+0x7c/0xb0
[27.975466]  [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0

The recursion occurs when subscr_terminate tries to grab the
subscriber lock, which is already taken by subscr_conn_msg_event.
We fix this by checking if the request to establish a new
subscription was successful, and if not we initiate termination of
the subscriber after we have released the subscriber lock.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:

1) The original code drops all packets with a multicast destination address,
	even though neighbor solicitations are sent to the solicited-node
	address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
	solicited node address, rather than the target address from the
	neighbor solicitation. So neighbor lookups would always fail if it
	got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
	The context for neigh_reduce() is the transmit path, vxlan_xmit(),
	where the host or a bridge-attached neighbor is trying to transmit
	a neighbor solicitation. To respond to it, the tunnel endpoint needs
	to do a *receive* of the appropriate neighbor advertisement. Doing a
	send, would only try to send the advertisement, encapsulated, to the
	remote destinations in the fdb -- hosts that definitely did not do the
	corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
	isrouter flag in the advertisement. This has nothing to do with whether
	or not the target is a router, and generally won't be set since the
	tunnel endpoint is bridging, not routing, traffic.

	The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.
Signed-off-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Christian Riesch says:

====================
net: davinci_emac: Fix interrupt requests and error handling

since commit 6892b41d (Linux 3.11) the
davinci_emac driver is broken. After doing ifconfig down, ifconfig up,
requesting the interrupts for the driver fails. The interface remains dead
until the board is rebooted.

The first patch in this patchset reverts commit
6892b41d partially and makes the driver
useable again.

During the work on the first patch, a number of bugs in the error handling
of the driver's ndo_open code were found. The second patch fixes these bugs.

I believe the first patch meets the rules for stable kernels, I therefore added
the stable tag to this patch. The second patch is just cleanup, the code
that is fixed by this patch is only executed in case of an error.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.

  1) Freeing the interrupts. The current code will not free all interrupts
     that were requested by the driver. Furthermore,  the code tries to do a
     platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
     iteration.

     This patch fixes these bugs.

  2) Wrong order of err: and rollback: labels. If the setup of the PHY in
     the code fails, the interrupts that have been requested before are
     not freed:

        request irq
                if requesting irqs fails, goto rollback
        setup phy
                if phy setup fails, goto err
        return 0

     rollback:
        free irqs
     err:

     This patch brings the code into the correct order.

  3) The code calls napi_enable() and emac_int_enable(), but does not
     undo both in case of an error.

     This patch adds calls of emac_int_disable() and napi_disable() to the
     rollback code.

  4) RX DMA descriptors are not freed in case of an error: Right before
     requesting the irqs, the function creates DMA descriptors for the
     RX channel. These RX descriptors are never freed when we jump to either
     rollback or err.

     This patch adds code for freeing the DMA descriptors in the case of
     an initialization error. This required a modification of
     cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
     function to free the DMA descriptors while the DMA channels are
     in IDLE state (before cpdma_ctlr_start() was called).

Tested on a custom board with the Texas Instruments AM1808.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 6892b41d

Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date:   Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api

the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.

This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: NJon Ringle <jon@ringle.org>
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Neighbor Solicitation is ipv6 protocol, so we should check
skb->protocol with ETH_P_IPV6
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In arch_cpu_idle() we must enable %pil based interrupts before
potentially invoking the hypervisor cpu yield call.

As per the Hypervisor API documentation for cpu_yield:

	Interrupts which are blocked by some mechanism other that
	pstate.ie (for example %pil) are not guaranteed to cause
	a return from this service.

It seems that only first generation Niagara chips are hit by this
bug.  My best guess is that later chips implement this in hardware
and wake up anyways from %pil events, whereas in first generation
chips the yield is implemented completely in hypervisor code and
requires %pil to be enabled in order to wake properly from this
call.

Fixes: 87fa05ae ("sparc: Use generic idle loop")
Reported-by: NFabio M. Di Nitto <fabbione@fabbione.net>
Reported-by: NJan Engelhardt <jengelh@inai.de>
Tested-by: NJan Engelhardt <jengelh@inai.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.

Fixes: 66fda75f (regulator: core: Replace direct ops->disable usage)
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the arch_{spin,read,write}_relax macros default to cpu_relax(),
remove the redundant definitions for parisc.

Cc: Helge Deller <deller@gmx.de>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NHelge Deller <deller@gmx.de>

We seem to be nearly the only platform which does not provide the
sys_utimes syscall.  Adding it now makes our life much easier with
userspace applications (like dietlibc and e2fsprogs) since we then
behave like all other platforms too and don't need extra patches which
are hard to get upstream anyway because we are not a mainstream
architecture.
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13

The attached change removes the unused and experimental
CONFIG_PARISC_TMPALIAS code. It doesn't work and I don't believe it will
ever be used.
Signed-off-by: NJohn David Anglin <dave.anglin@bell.net>
Signed-off-by: NHelge Deller <deller@gmx.de>

STI console is used on parisc and m68k HP machines. This patch partly reverts
my previous commit and as such restores the fonts for the m68k machines.
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13

Pull perf fixes from Ingo Molnar:
 "Two oneliner 'perf bench' tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf bench: Fix NULL pointer dereference in "perf bench all"
  perf bench numa: Make no args mean 'run all tests'

Pull ARM SoC fixes from Olof Johansson:
 "Only two patches this time, one to fix ethernet probe order on at91
  (better fix with proper device aliasing will be done for 3.15, this is
  stop-gap), and one update to MAINTAINERS due to Freescale moving their
  repo to kernel.org"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: at91: fix network interface ordering for sama5d36
  MAINTAINERS: update IMX kernel git tree

Pull drm fixes from Dave Airlie:
 "Some final few intel fixes, all regressions, all stable cc, and one
  exynos oops fixer.

  The biggest is probably the intel display error irqs one, but it seems
  to fix a few crashes on startup, and one use after free in drm core"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/exynos: Fix (more) freeing issues in exynos_drm_drv.c
  drm/i915: Disable stolen memory when DMAR is active
  Revert "drm/i915: don't touch the VDD when disabling the panel"
  drm: Fix use-after-free in the shadow-attache exit code
  drm/i915: Don't enable display error interrupts from the start
  drm/i915: Fix scanline counter fixup on BDW
  drm/i915: Add a workaround for HSW scanline counter weirdness
  drm/i915: Fix PSR programming

Commit 7982e90c ("block: fix q->flush_rq NULL pointer crash on
dm-mpath flush") moved an allocation to blk_init_allocated_queue(), but
neglected to free that allocation on the error paths that follow.
Signed-off-by: NDave Jones <davej@fedoraproject.org>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJens Axboe <axboe@fb.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Srikar Dronamraju reports that commit b0c29f79 ("futexes: Avoid
taking the hb->lock if there's nothing to wake up") causes java threads
getting stuck on futexes when runing specjbb on a power7 numa box.

The cause appears to be that the powerpc spinlocks aren't using the same
ticket lock model that we use on x86 (and other) architectures, which in
turn result in the "spin_is_locked()" test in hb_waiters_pending()
occasionally reporting an unlocked spinlock even when there are pending
waiters.

So this reinstates Davidlohr Bueso's original explicit waiter counting
code, which I had convinced Davidlohr to drop in favor of figuring out
the pending waiters by just using the existing state of the spinlock and
the wait queue.
Reported-and-tested-by: NSrikar Dronamraju <srikar@linux.vnet.ibm.com>
Original-code-by: NDavidlohr Bueso <davidlohr@hp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge tag 'trace-fixes-v3.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull trace fix from Steven Rostedt:
 "Vaibhav Nagarnaik discovered that since 3.10 a clean-up patch made the
  array index in the trace event format bogus.

  He supplied an elegant solution that uses __stringify() and also
  removes the need for the event_storage and event_storage_mutex and
  also cuts off a few K of overhead from the trace events"

* tag 'trace-fixes-v3.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix array size mismatch in format string

Add remove_linear_migration_ptes_from_nonlinear(), to fix an interesting
little include/linux/swapops.h:131 BUG_ON(!PageLocked) found by trinity:
indicating that remove_migration_ptes() failed to find one of the
migration entries that was temporarily inserted.

The problem comes from remap_file_pages()'s switch from vma_interval_tree
(good for inserting the migration entry) to i_mmap_nonlinear list (no good
for locating it again); but can only be a problem if the remap_file_pages()
range does not cover the whole of the vma (zap_pte() clears the range).

remove_migration_ptes() needs a file_nonlinear method to go down the
i_mmap_nonlinear list, applying linear location to look for migration
entries in those vmas too, just in case there was this race.

The file_nonlinear method does need rmap_walk_control.arg to do this;
but it never needed vma passed in - vma comes from its own iteration.
Reported-and-tested-by: NDave Jones <davej@redhat.com>
Reported-and-tested-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Jesse Gross says:

====================
Open vSwitch

Four small fixes for net/3.14. I realize that these are late in the
cycle - just got back from vacation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 812e44dd ("ip6mr: advertise new mfc entries via rtnl") reuses the
function ip6mr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.

Libraries like libnl will wait forever for NLMSG_DONE.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8cd3ac9f ("ipmr: advertise new mfc entries via rtnl") reuses the
function ipmr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.

Libraries like libnl will wait forever for NLMSG_DONE.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3ff661c3 ("net: rtnetlink notify events for FDB NTF_SELF adds and
deletes") reuses the function nlmsg_populate_fdb_fill() to notify fdb events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.

Libraries like libnl will wait forever for NLMSG_DONE.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While it is true that getnstimeofday() uses about 40 cycles if TSC
is available, it can use 1600 cycles if hpet is the clocksource.

Switch to get_jiffies_64(), as this is more than enough, and
go back to 60 seconds periods.

Fixes: 8c27bd75 ("tcp: syncookies: reduce cookie lifetime to 128 seconds")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation for how to use netlink mmap interface is incorrect.
The calls to setsockopt() require an additional argument.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull MIPS fixes from Ralf Baechle:
 "Another set of five fixes.  The most interesting one is a fix for race
  condition in the local_irq_disable() implementation used by .S code
  for pre-MIPS R2 processors only.  It leaves a race that's hard but not
  impossible to hit; the others fairly obvious"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Make local_irq_disable macro safe for non-Mipsr2
  MIPS: Octeon: Fix warning in of_device_alloc on cn3xxx
  MIPS: ftrace: Tweak safe_load()/safe_store() macros
  MIPS: BCM47XX: Check all (32) GPIOs when looking for a pin
  MIPS: Fix possible build error with transparent hugepages enabled

Pull sound fixes from Takashi Iwai:
 "Just two minor bug fixes: a fix for a regression in oxygen driver that
  was introduced in 3.14-rc1, and a stable fix for the return value of
  compress offload open callback"

* tag 'sound-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: compress: Pass through return value of open ops callback
  ALSA: oxygen: Xonar DG(X): fix Stereo Upmixing regression

The kernel starts out its "jiffies" timer as 5 minutes below zero, as
shown in include/linux/jiffies.h:

  /*
   * Have the 32 bit jiffies value wrap 5 minutes after boot
   * so jiffies wrap bugs show up earlier.
   */
  #define INITIAL_JIFFIES ((unsigned long)(unsigned int) (-300*HZ))

The loop in ovs_flow_stats_get() starts out with 'used' set to 0, then
takes any "later" time.  This means that for the first five minutes after
boot, flows will always be reported as never used, since 0 is greater than
any time already seen.
Signed-off-by: NBen Pfaff <blp@nicira.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

In event format strings, the array size is reported in two locations.
One in array subscript and then via the "size:" attribute. The values
reported there have a mismatch.

For e.g., in sched:sched_switch the prev_comm and next_comm character
arrays have subscript values as [32] where as the actual field size is
16.

name: sched_switch
ID: 301
format:
        field:unsigned short common_type;       offset:0;       size:2; signed:0;
        field:unsigned char common_flags;       offset:2;       size:1; signed:0;
        field:unsigned char common_preempt_count;       offset:3;       size:1;signed:0;
        field:int common_pid;   offset:4;       size:4; signed:1;

        field:char prev_comm[32];       offset:8;       size:16;        signed:1;
        field:pid_t prev_pid;   offset:24;      size:4; signed:1;
        field:int prev_prio;    offset:28;      size:4; signed:1;
        field:long prev_state;  offset:32;      size:8; signed:1;
        field:char next_comm[32];       offset:40;      size:16;        signed:1;
        field:pid_t next_pid;   offset:56;      size:4; signed:1;
        field:int next_prio;    offset:60;      size:4; signed:1;

After bisection, the following commit was blamed:
92edca07 tracing: Use direct field, type and system names

This commit removes the duplication of strings for field->name and
field->type assuming that all the strings passed in
__trace_define_field() are immutable. This is not true for arrays, where
the type string is created in event_storage variable and field->type for
all array fields points to event_storage.

Use __stringify() to create a string constant for the type string.

Also, get rid of event_storage and event_storage_mutex that are not
needed anymore.

also, an added benefit is that this reduces the overhead of events a bit more:

   text    data     bss     dec     hex filename
8424787 2036472 1302528 11763787         b3804b vmlinux
8420814 2036408 1302528 11759750         b37086 vmlinux.patched

Link: http://lkml.kernel.org/r/1392349908-29685-1-git-send-email-vnagarnaik@google.com

Cc: Laurent Chavey <chavey@google.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NVaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

For non-mipsr2 processors, the local_irq_disable contains an mfc0-mtc0
pair with instructions inbetween.  With preemption enabled, this sequence
may get preempted and effect a stale value of CP0_STATUS when executing
the mtc0 instruction.  This commit avoids this scenario by incrementing
the preempt count before the mfc0 and decrementing it after the mtc9.

[ralf@linux-mips.org: This patch is sorting out the part that were missed
by e97c5b60 [MIPS: Make irqflags.h functions preempt-safe for non-mipsr2
cpus.]  I also re-enabled the inclusion of <asm/asm-offsets.h> at the top
of <asm/asmmacro.h>].
Signed-off-by: NJim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6164/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes

 Just fixed resource release issue at open fail.

* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: Fix (more) freeing issues in exynos_drm_drv.c

The following commit [0] fixed a use-after-free, but left the subdrv open
in the error path.

[0] commit 6ca605f7
drm/exynos: Fix freeing issues in exynos_drm_drv.c
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Fix some "Bad rss-counter state" reports on exit, arising from the
interaction between page migration and remap_file_pages(): zap_pte()
must count a migration entry when zapping it.

And yes, it is possible (though very unusual) to find an anon page or
swap entry in a VM_SHARED nonlinear mapping: coming from that horrid
get_user_pages(write, force) case which COWs even in a shared mapping.
Signed-off-by: NHugh Dickins <hughd@google.com>
Tested-by: Sasha Levin sasha.levin@oracle.com>
Tested-by: Dave Jones davej@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull PCI resource management fix from Bjorn Helgaas:
 "This is a fix for an AGP regression exposed by e501b3d8 ("agp:
  Support 64-bit APBASE"), which we merged in v3.14-rc1.

  We've warned about the conflict between the GART and PCI resources and
  cleared out the PCI resource for a long time, but after e501b3d8,
  we still *use* that cleared-out PCI resource.  I think the GART
  resource is incorrect, so this patch removes it"

* tag 'pci-v3.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "[PATCH] Insert GART region into resource map"

Pull cgroup fix from Tejun Heo:
 "One really late cgroup patch to fix error path in create_css().
  Hitting this bug would be pretty rare but still possible and it gets
  delayed we'd need to backport it through -stable anyway.  It only
  updates error path in create_css() and has low chance of new
  breakages"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix a failure path in create_css()