Changes include:

1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
   the board capability of this pin to wakeup the system

2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
   enable/disable wakeup from GPIOs and keypad GPIO

   * these functions are currently kept in mfp-pxa2xx.c due to their
     dependency to the MFP configuration

3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
   is set on incorrect pins

So that the GPIO's wakeup capability is now decided by the following:

   a) processor's capability: (only those GPIOs which have dedicated
      bits within PWER/PRER/PFER can wakeup the system), this is
      initialized by pxa{25x,27x}_init_mfp()

   b) board design decides:
      - whether the pin is designed to wakeup the system (some of
        the GPIOs are configured as other functions, which is not
        intended to be a wakeup source), by OR'ing the pin config
        with MFP_LPM_CAN_WAKEUP

      - which edge the pin is designed to wakeup the system, this
        may depends on external peripherals/connections, which is
        totally board specific; this is indicated by MFP_LPM_EDGE_*

   c) the corresponding device's (most likely the gpio_keys.c) wakeup
      attribute:
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. the following code to configure PGSRx is no way portable and
   intuitive:

-	PGSR0 = 0x00008800;
-       PGSR1 = 0x00000002;
-       PGSR2 = 0x0001FC00;
-       PGSR3 = 0x00001F81;

   this is removed as low power state has already been encoded in
   the pin configuration definitions.

   Note: there is no specific reason for some of the GPIOs to drive
   high in low power mode as indicated by the above setting, those
   bits are ignored, and the result is validated to work.

2. the following code to configure GPIO wakeup is removed as this
   is now totally handled by pxa2xx_mfp_config():

-       PWER  = 0xC0000002;
-       PRER  = 0x00000002;
-       PFER  = 0x00000002;
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

for use by other platforms
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs.  A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.

A pin configuration on pxa{25x,27x} is composed of:

    - alternate function selection (or pin mux as commonly called)
    - low power state or sleep state
    - wakeup enabling from low power mode

The following MFP_xxx bit definitions in mfp.h are re-used:

    - MFP_PIN(x)
    - MFP_AFx
    - MFP_LPM_DRIVE_{LOW, HIGH}
    - MFP_LPM_EDGE_*

Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:

    - MFP_CFG_IN  : for input alternate functions
    - MFP_CFG_OUT : for output alternate functions

Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT().  As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.

Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output.  The actual
direction of the GPIO is configured by gpio_direction_{input, output}

Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.

E.g.  invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:

    enable_irq_wake( gpio_to_irq(35) );

To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).

Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:

    - MFP_LPM_WAKEUP_ENABLE

The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:

    - WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
    - WAKEUP_ON_LEVEL_HIGH

The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.

These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.

The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

two reasons:
1. GPIO namings and their mode definitions are conceptually not part
   of the PXA register definitions

2. this is actually a temporary move in the transition of PXA2xx to
   use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
   code will still work and new code can be added in step by step
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

MFP configurations after resume should be done before the GPIO registers
are restored.  Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:

1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
   registers are already configured on pxa{25x,27x} while returns
   0 always on pxa3xx

2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
   ment of GPDRx, the side effect of this change is that the pin
   _must_ be configured before use, pxa_gpio_irq_type() will not
   change the pin to GPIO, as this restriction is sane, esp. with
   the new MFP framework
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

To further clean up the GPIO and IRQ structure:

1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
   function pxa_init_gpio()

2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
   an argument
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes the code better organized and simplified a bit.  The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.

This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable.  The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)

The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).

"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

by

1. wrapping long lines and making comments tidy

2. using IRQ_TYPE_* instead of migration macros __IRQT_*

3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
   stuff
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

by:

1. introduce dedicated pxa_{mask,unmask}_low_gpio()

2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
   initialized in pxa_init_irq()

3. introduce dedicated pxa_init_gpio_set_wake()
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. As David Brownell suggests, using ffs() is going to make the loop
   a bit faster (by avoiding unnecessary shift and iteration)

2. Russell suggested find_{first,next}_bit() being used with the
   gedr[] array
Signed-off-by: Neric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Enhanced GPIO alternate functions descriptions,
taken from Intel PXA270 Developers Manual.
Signed-off-by: NRobert Jarzmik <rjarzmik@free.fr>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes the builtin RTL8139 NIC on the Medion MD9580-F laptop.  The
BIOS reports the interrupt routing incorrectly.  I recently added a
quirk to work around this, and this patch fixes a typo in the quirk.

We pad every ACPI pathname component to four characters, so ".ISA." will
never match anything.  We need ".ISA_." instead.

Thank you Johann-Nikolaus Andreae <johann-nikolaus.andreae@nacs.de>
for patiently testing this patch.

See http://bugzilla.kernel.org/show_bug.cgi?id=4773Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Fix docbook problem
  ASoC/TLV320AIC3X: Stop I2C driver ID abuse
  i2c-omap: Fix unhandled fault
  i2c-bfin-twi: Disable BF54x support for now

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: MMU: Fix memory leak on guest demand faults
  KVM: VMX: convert init_rmode_tss() to slots_lock
  KVM: MMU: handle page removal with shadow mapping
  KVM: MMU: Fix is_rmap_pte() with io ptes
  KVM: VMX: Restore tss even on x86_64

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  [PATCH] get stack footprint of pathname resolution back to relative sanity
  [PATCH] double iput() on failure exit in hugetlb
  [PATCH] double dput() on failure exit in tiny-shmem
  [PATCH] fix up new filp allocators
  [PATCH] check for null vfsmount in dentry_open()
  [PATCH] reiserfs: eliminate private use of struct file in xattr
  [PATCH] sanitize hppfs
  hppfs pass vfsmount to dentry_open()
  [PATCH] restore export of do_kern_mount()

While backporting 72dc67a6, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline).  This caused a page reference leak, resulting in a
fairly massive memory leak.

Fix by removing the extraneous gfn_to_page() call.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

init_rmode_tss was forgotten during the conversion from mmap_sem to
slots_lock.

INFO: task qemu-system-x86:3748 blocked for more than 120 seconds.
Call Trace:
 [<ffffffff8053d100>] __down_read+0x86/0x9e
 [<ffffffff8053fb43>] do_page_fault+0x346/0x78e
 [<ffffffff8053d235>] trace_hardirqs_on_thunk+0x35/0x3a
 [<ffffffff8053dcad>] error_exit+0x0/0xa9
 [<ffffffff8035a7a7>] copy_user_generic_string+0x17/0x40
 [<ffffffff88099a8a>] :kvm:kvm_write_guest_page+0x3e/0x5f
 [<ffffffff880b661a>] :kvm_intel:init_rmode_tss+0xa7/0xf9
 [<ffffffff880b7d7e>] :kvm_intel:vmx_vcpu_reset+0x10/0x38a
 [<ffffffff8809b9a5>] :kvm:kvm_arch_vcpu_setup+0x20/0x53
 [<ffffffff8809a1e4>] :kvm:kvm_vm_ioctl+0xad/0x1cf
 [<ffffffff80249dea>] __lock_acquire+0x4f7/0xc28
 [<ffffffff8028fad9>] vfs_ioctl+0x21/0x6b
 [<ffffffff8028fd75>] do_vfs_ioctl+0x252/0x26b
 [<ffffffff8028fdca>] sys_ioctl+0x3c/0x5e
 [<ffffffff8020b01b>] system_call_after_swapgs+0x7b/0x80
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Do not assume that a shadow mapping will always point to the same host
frame number.  Fixes crash with madvise(MADV_DONTNEED).

[avi: move after first printk(), add another printk()]
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

is_rmap_pte() doesn't take into account io ptes, which have the avail bit set.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

The vmx hardware state restore restores the tss selector and base address, but
not its length.  Usually, this does not matter since most of the tss contents
is within the default length of 0x67.  However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted.  The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.

Fix by restoring the tss length.  Note that i386 had this working already.

Closes bugzilla 10246.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: Fix cut-and-paste error in rtl8150.c
  USB: ehci: stop vt6212 bus hogging
  USB: sierra: add another device id
  USB: sierra: dma fixes
  USB: add support for Motorola ROKR Z6 cellphone in mass storage mode
  USB: isd200: fix memory leak in isd200_get_inquiry_data
  USB: pl2303: another product ID
  USB: new quirk flag to avoid Set-Interface
  USB: fix gadgetfs class request delegation

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  driver core: debug for bad dev_attr_show() return value.
  UIO: add pgprot_noncached() to UIO mmap code

Revert as it is reported to cause problems for people.

commit 4348a2dc
Author: Shaohua Li <shaohua.li@intel.com>
Date:   Wed Oct 24 10:45:08 2007 +0800

    pcie: utilize pcie transaction pending bit

    PCIE has a mechanism to wait for Non-Posted request to complete. I think
    pci_disable_device is a good place to do this.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065

Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Soeren Sonnenburg <kernel@nn7.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

lockdep goes off on the iova copy_reserved_iova() because it and a function
it calls grabs locks in the from, and the to of the copy operation.

The function grab locks of the same lock classes triggering the warning.  The
first lock grabbed is for the constant reserved areas that is never accessed
after early boot.  Technically you could do without grabbing the locks for the
"from" structure its copying reserved areas from.

But dropping the from locks to me looks wrong, even though it would be ok.

The affected code only runs in early boot as its setting up the DMAR
engines.

This patch gives the reserved_ioval_list locks special lockdep classes.
Signed-off-by: NMark Gross <mgross@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Try to find the culprit who caused
http://bugzilla.kernel.org/show_bug.cgi?id=10150

Cc: <balajirrao@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Mapping of physical memory in UIO needs pgprot_noncached() to ensure
that IO memory is not cached. Without pgprot_noncached(), it (accidentally)
works on x86 and arm, but fails on PPC.
Signed-off-by: NJean-Samuel Chenard <jsamch@gmail.com>
Signed-off-by: NHans J Koch <hjk@linutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>