- 20 5月, 2011 2 次提交
-
-
由 Suresh Siddha 提交于
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com> Cc: daniel.blueman@gmail.com Link: http://lkml.kernel.org/r/20110518233157.994002011@sbsiddha-MOBL3.sc.intel.comSigned-off-by: NIngo Molnar <mingo@elte.hu>
-
由 Suresh Siddha 提交于
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com> Cc: daniel.blueman@gmail.com Link: http://lkml.kernel.org/r/20110518233157.909013179@sbsiddha-MOBL3.sc.intel.comSigned-off-by: NIngo Molnar <mingo@elte.hu>
-
- 28 4月, 2011 1 次提交
-
-
We use io_apic_setup_irq_pin() in order to configure pin's interrupt number polarity and type. This is done on every irq_create_of_mapping() which happens for instance during pci enable calls. Level typed interrupts are masked by default, edge are unmasked. On the first ->xlate() call the level interrupt is configured and masked. The driver calls request_irq() and the line is unmasked. Lets assume the interrupt line is shared with another device and we call pci_enable_device() for this device. The ->xlate() configures the pin again and it is masked. request_irq() does not unmask the line because it _is_ already unmasked according to its internal state. So the interrupt will never be unmasked again. This patch is based on an earlier work by Torben Hohn and solves the problem by configuring the pin only once. Since all devices must agree on the same type and polarity there is no point in configuring the pin more than once. [ tglx: Split out the ce4100 part into a separate patch ] Cc: Torben Hohn <torbenh@linutronix.de> Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3ESigned-off-by: NThomas Gleixner <tglx@linutronix.de>
-
- 25 3月, 2011 2 次提交
-
-
由 Thomas Gleixner 提交于
That call escaped the name space cleanup. Fix it up. We really want to call there. The chip might have changed since the irq was setup initially. So let the core code and the chip decide what to do. The status is just an unreliable snapshot. Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
-
由 Thomas Gleixner 提交于
The xlate() function returns 0 or a negative error code. Returning the error code blindly will be seen as an huge irq number by the calling function because irq_create_of_mapping() returns an unsigned value. Return 0 (NO_IRQ) as required. Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
-
- 25 2月, 2011 1 次提交
-
-
由 Thomas Gleixner 提交于
Up to now we force enable the local apic in the devicetree setup uncoditionally and set smp_found_config unconditionally to 1 when a devicetree blob is available. This breaks, when local apic is disabled in the Kconfig. Make it consistent by initializing device tree explicitely before smp_get_config() so a non lapic configuration could be used as well. To be functional that would require to implement PIT as an interrupt host, but the only user of this code until now is ce4100 which requires apics to be available. So we leave this up to those who need it. Tested-by: NSebastian Siewior <bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
- 24 2月, 2011 8 次提交
-
-
Both OLPC and CE4100 activate CONFIG_OF. OLPC uses PROMTREE while CE uses FLATTREE. Compiling for OLPC only breaks due to missing flat tree functions and variables. Use proper wrappers and provide an empty x86_flattree_get_config() inline so OF=y FLATTREE=n builds and works. [ tglx: Make it work with HPET_TIMER=n and make a function static ] Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
ioapic_xlate provides a translation from the information in device tree to ioapic related informations. This includes - obtaining hw irq which is the vector number "=> pin number + gsi" - obtaining type (level/edge/..) - programming this information into ioapic ioapic_add_ofnode adds an irq_domain based on informations from the device tree. This information (irq_domain) is required in order to map a device to its proper interrupt controller. [ tglx: Adapted to the io_apic changes, which let us move that whole code to devicetree.c ] Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org LKML-Reference: <1298405266-1624-10-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
For now we probe these busses and we change this to board dependent probes once we have to. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org LKML-Reference: <1298405266-1624-9-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
x86_of_pci_init() does two things: - it provides a generic irq enable and disable function. enable queries the device tree for the interrupt information, calls ->xlate on the irq host and updates the pci->irq information for the device. - it walks through PCI bus(es) in the device tree and adds its children (device) nodes to appropriate pci_dev nodes in kernel. So the dtb node information is available at probe time of the PCI device. Adding a PCI bus based on the information in the device tree is currently not supported. Right now direct access via ioports is used. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: NDirk Brandewie <dirk.brandewie@gmail.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org LKML-Reference: <1298405266-1624-8-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
Set hpet_address based on information provied form DTB Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org Cc: Dirk Brandewie <dirk.brandewie@gmail.com> LKML-Reference: <1298405266-1624-7-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
APIC and IO_APIC have to be added to the system early because native_init_IRQ() requires it. In order to obtain the address of the ioapic the device tree has to be unflattened so of_address_to_resource() works. The device tree is relocated to ensure it is always covered by the kernel mapping. That way the boot loader does not have to make any assumptions about kernel's memory layout. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org Cc: Dirk Brandewie <dirk.brandewie@gmail.com> LKML-Reference: <1298405266-1624-6-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
The here introduced irq_domain abstraction represents a generic irq controller. It is a subset of powerpc's irq_host which is going to be renamed to irq_domain and then become generic. This implementation will be removed once it is generic. The xlate callback is resposible to parse irq informations like irq type and number and returns the hardware irq number which is reported by the hardware as active. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: NDirk Brandewie <dirk.brandewie@gmail.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org LKML-Reference: <1298405266-1624-5-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
This patch adds minimal support for device tree on x86. The device tree blob is passed to the kernel via setup_data which requires at least boot protocol 2.09. Memory size, restricted memory regions, boot arguments are gathered the traditional way so things like cmd_line are just here to let the code compile. The current plan is use the device tree as an extension and to gather information which can not be enumerated and would have to be hardcoded otherwise. This includes things like - which devices are on this I2C/SPI bus? - how are the interrupts wired to IO APIC? - where could my hpet be? Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Cc: sodaville@linutronix.de Cc: devicetree-discuss@lists.ozlabs.org LKML-Reference: <1298405266-1624-3-git-send-email-bigeasy@linutronix.de> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-