Replace uses of I40E_LENGTH_OF_ADDRESS with ETH_ALEN.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware can occasionally give an interrupt on the misc
queue for which there is no driver work to do.  In that case
the driver was not re-enabling interrupts even though they
were auto masked by hardware.  This left interrupts disabled
on this queue.

Re-enable the interrupt whenever leaving this function.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When cleaning descriptors, we must set up ALL fields, not just the DMA
address. The initial setup does this correctly, but not the cleanup
code, so the firmware would process the ring exactly once and then fail.

Change-ID: I2930b83c76194b3016a8ac0fa693f9a573995640
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The admin queue length register is updated in
config_a<sq|rq>_regs functions.  We should not update it again,
as we will trigger firmware to init the AQ again. In this case
firmware will lose the information about the AQ Rx tail position
and will see Rx queue as full (no free desc for FW to use).
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF VSI was never updated to enable or disable internal switch loopback
when VFs were created or destroyed via the sysfs interface.  Add some
helper functions to take care of that.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Addresses a few code format issues that have crept in over time.

Change-Id: I1a62cbd16b29a218a933b0f7176abe748f9615e8
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rework Shadow RAM read word/buffer functions to not use AQ Request
Resource commands.  Requesting resource is not needed for SR read
operations which are done through SRCTL register.  Access to SR through
register is controlled through DONE bit within SRCTL.  With this change
we do not block whole NVM resource for SR read operations.

Change-Id: I73e96cdea39a45ee7b5bdf038e527308de2d9efe
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to check if we are dealing with the correct MAC type before we
try to read anything from the registers.

Change-Id: I3989516999d06c3009e87d6a2eafc20af305c5c2
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move PF ID initialization code from PF reset routine to earlier driver
initialization function.  There are a few operations which need the
PF ID before the first PF reset is called.

Change-Id: I7e971f7556b46a837149850ec05ce115c35db575
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use a smaller range of test registers in MFP mode as there are fewer
resources than when in SFP mode.

Change-Id: I08424890c3f57b5dde5ee99e99724ce252e0875a
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware's AdminQ interface has matured a little, so update the
code to use the new fields and values.

Change-Id: I8fcd7b443f268dcf9346bd6a9e940fe9c2958891
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The RSTAT comes back with DEVICE READY to indicate that the HW is ready,
but we still have to wait for the FW to indicate that the Core and Global
modules are back up again.  This needs a read of the NVM_ULD register.

Change-Id: I88276165f9cd446d2f166fb4b8cff00521af4bec
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Version update to 0.3.25-k
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF is allowed to request the PF to set its already assigned
MAC address without generating an error.

Change-Id: I8dfdf353396995dbbb26cafab4e42b451911da3d
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the 8021q driver is loaded it sets VLAN 0 filters on all devices.
This does not mean that any VLAN tagged packet should be accepted.
Instead accept only VLAN 0 tagged packets so that upper layers can
interpret the priority bits.

Change-Id: I17274a540b613749612ffe23a3aef2b8ee6ff6a4
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Broadcast promiscuous should only be turned on when general
promiscuous mode is turned on, otherwise VLAN tagged packets out of
the assigned VLAN domain are received.

Add a broadcast MAC filter in order to continue to receive
broadcast traffic on VLANs, MAIN or VMDQ VSI.

Change-Id: I99d8e382a082ee51201228f1226af3b46452ac55
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add more functionality to debugfs to assist development
and testing of AQ commands.

adds:
send aq_cmd
send indirect aq_cmd

Change-Id: I01710cddd33110a6c1e1aabf84cb6e93cda4c42a
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that mlx4_en includes a PHC driver it must select PTP_1588_CLOCK.

   drivers/built-in.o: In function `mlx4_en_get_ts_info':
>> en_ethtool.c:(.text+0x391a11): undefined reference to `ptp_clock_index'
   drivers/built-in.o: In function `mlx4_en_remove_timestamp':
>> (.text+0x397913): undefined reference to `ptp_clock_unregister'
   drivers/built-in.o: In function `mlx4_en_init_timestamp':
>> (.text+0x397b20): undefined reference to `ptp_clock_register'

Fixes: ad7d4eae ("mlx4_en: Add PTP hardware clock")
Signed-off-by: NShawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0.

Fixes: 837052d0 ('net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling')
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 - Replace pr_warn_ratelimited() with net_ratelimit() and netdev_warn().
 - Adjust the algnment of some messages.
 - Remove the peroid.
 - Fix some messages don't have terminating newline.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> as reported for linux-next of Dec.20, 2013
> when CONFIG_NEED_DMA_MAP_STATE is not enabled:
>
> drivers/net/ethernet/brocade/bna/bnad.c: In function 'bnad_start_xmit':
> drivers/net/ethernet/brocade/bna/bnad.c:3074:26: error: 'struct bnad_tx_vector' has no member named 'dma_len'
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes some typos found by Sergei.
Reported-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla posted a patch trying to address following problem :

<quote>
 The vxlan driver sets itself as the socket owner for all the TX flows
 it encapsulates (using vxlan_set_owner()) and assigns it's own skb
 destructor. This causes all tunneled traffic to land up on only one TXQ
 as all encapsulated skbs refer to the vxlan socket and not the original
 socket.  Also, the vxlan skb destructor breaks some functionality for
 tunneled traffic like wmem accounting and as TCP small queues and
 FQ/pacing packet scheduler.
</quote>

I reworked Sathya patch and added some explanations.

vxlan_xmit() can avoid one skb_clone()/dev_kfree_skb() pair
and gain better drop monitor accuracy, by calling kfree_skb() when
appropriate.

The UDP socket used by vxlan to perform encapsulation of xmit packets
do not need to be alive while packets leave vxlan code. Its better
to keep original socket ownership to get proper feedback from qdisc and
NIC layers.

We use skb->sk to

A) control amount of bytes/packets queued on behalf of a socket, but
prior vxlan code did the skb->sk transfert without any limit/control
on vxlan socket sk_sndbuf.

B) security purposes (as selinux) or netfilter uses, and I do not think
anything is prepared to handle vxlan stacked case in this area.

By not changing ownership, vxlan tunnels behave like other tunnels.
As Stephen mentioned, we might do the same change in L2TP.
Reported-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing serial state notification handling expected older Option
devices, having a hardcoded assumption that the Modem port was always
USB interface #2.  That isn't true for devices from the past few years.

hso_serial_state_notification is a local cache of a USB Communications
Interface Class SERIAL_STATE notification from the device, and the
USB CDC specification (section 6.3, table 67 "Class-Specific Notifications")
defines wIndex as the USB interface the event applies to.  For hso
devices this will always be the Modem port, as the Modem port is the
only port which is set up to receive them by the driver.

So instead of always expecting USB interface #2, instead validate the
notification with the actual USB interface number of the Modem port.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Tested-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It returns 0 in case of success, !0 error otherwise. Fix the improper error
verification.

Fixes: 2c9839c1 ("bonding: add num_grat_arp attribute netlink support")
CC: sfeldma@cumulusnetworks.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Acked-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the boolean value with the error code for the return value
of the rtl_ops_init().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some information of the device may be used in other functions. Move
the relative code to make sure it would be initialzed correctly
before using it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the tabs of the variables declaration with the spaces.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver wrongly assumes 16 EQs/vectors are available for each BE3 PF.
When SR-IOV is enabled, a BE3 PF can support only a max of 8 EQs.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The loopback test FW cmd may need upto 15 seconds to complete on
certain PHYs. This patch also fixes the name of the completion variable
used to synchronize FW cmd completions as it not used by the flashing
cmd alone anymore.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When *only* the default RXQ is used, the RSS policy must be disabled so
that all IP and no-IP traffic is placed into the default RXQ. If not,
IP traffic is dropped.

Also, issue the RSS_CONFIG cmd only if FW advertises RSS capability for
the interface.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device is not in a working state avoid making admin
queue (AQ) calls that rely on a working AQ.

Change-Id: Ifbba6d257b3a5b51bfe92938c04088c0baa21433
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver needs to make sure the send queue is alive before
trying to use it.

Chagne-Id: I9bd1f6159c45c98e63f562e3a8dfb57edfe50e13
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Always call the AQ call to shutdown the queue in the shutdown path.

Check ASQ is alive before issuing the AQ command since we might be
resetting to recover from a bad state in which case we should not
issue the AQ command.

Use the register variable for length so it can be used by PF, VF
and GL AQ commands.

Change-Id: Ic3d305687ea3f1a6afa84e864b7a27bd38a9af32
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF VSI Port VLAN settings still allow the user to view VLAN tag in
the descriptor.  Fix the settings to hide the VLAN ID from the VF. The
VF is not supposed to be aware it is on a VLAN in the Port VLAN
scenario.

Change-Id: I976f2bacb455dbb750f8c53a781c689f02cb8907
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The get_vsi_params and update_vsi_params functions were using a
different command struct that just happened to have an seid element in
the right place and so worked correctly anyway.  This patch fixes the
functions to use the right data struct.

There is no actual logic change.

Change-Id: I513b5e1dc293dfd5b2ba4fa443cbdbfa608d9d19
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a problem where the 'ip link show' command would display stale
link address information after the link address was set via the 'ip
link set' command.  In addition, fix problem with the user being
allowed to overwrite the administratively set VF MAC address.

Change-Id: I669ed14e55f2b633ef7b456b713632b08468671c
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When communicating with VF devices over the AQ, the FW refers to the
VF by its global VF ID, not local the VF ID with reference to its
parent PF. Since the global and local VF IDs are identical for PF 0,
the code worked correctly on PF 0.

However, we cannot just use global IDs throughout the code as most of
the other references to the VF (VSI setup, register offsets, etc.)
require the local VF ID. Instead, we just add or subtract our base VF
ID when sending and receiving AQ messages.

Change-Id: I92f4332b4876bc68b2f9af9ebf48761f63b6bd97
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When SR-IOV is disabled, the (now nonexistent) virtual function
devices undergo a VFLR event. We don't need to handle this event
because the VFs are gone, but we do need to tell the HW that they are
complete. This fixes an issue with a phantom VFLR and broken VFs when
SR-IOV is re-enabled.

Change-Id: I7580b49ded0158172a85b14661ec212af77000c8
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Shockingly, the compiler didn't flag this uninitialized variable. This
fixes a potential memory corruption condition where ARQ messages are
written to random memory locations.

Change-Id: Iac82f4562d2bf3f42df3f3b2163d9cbed2160135
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>