Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the orion include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>

Hook these platforms restart code into the new restart hook rather than
using arch_reset().
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The eSata SheevaPlug and QNAP TS-209 devices were removed from
mach-types due to naming mismatches between machine_is_xxx(), CONFIG_XXX
and MACH_TYPE_XXX.

This patch fixes those mismatches and adds the devices back into
mach-types.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NJon Medhurst <tixy@yxit.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

This patch adds a second, red, led for the standard sheevaplug.
The sheeva_esata mpp config is left unchanged.

Tested on a standard sheevaplug
Signed-off-by: NRobin Becker <robin@reportlab.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

Accept SD CD and SD WP in accordance to
http://plugcomputer.org/data/docs/Sheeva-PowerPlug-V1.3-GTI-090906.pdf
on MPP 47 and 44 respectively on the eSATA SheevaPlug
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
--

Enable the kirkwood SATA SoC interface on the eSATA SheevaPlug.
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
--

Allow basic eSATA SheevaPlug board configuration and build.
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
--

Common resource and platform device structures are moved to common.c
and only the partition table and chip delay remains a per board
parameter.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>

Ideally, the default should be set to 0 and let the EHCI driver turn
it on as needed.  This makes USB usable in the mean time.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>