The SBCF firmware format has been extended to support extra headers
after the main payload. These extra headers are used to sign the
firmware code with more than one certificate. This eases up
distributing single code images that work in more than one SKU of the
device.

The changes to support this feature will be spread in a series of
commits. This one just adds the support to parse the extra headers and
store them in i2400m->fw_hdrs. Coming changes to the loader code will
use that to determine which header to upload to the device.

The i2400m_fw_check() function now iterates over all the headers and
for each, calls i2400m_fw_hdr_check(), which does some basic checks on
each header. It then stores the headers for the bootloader code to use.

The i2400m_dev_bootstrap() function has been modified to cleanup
i2400m->fw_hdrs when done.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Make sure the bootloading code checks that the format of the file is
understood (major version match). This also fixes a dumb typo in
extracting the major version field.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The i2400m based devices can get in a sort of a deadlock some times;
when they boot, they send a reboot "barker" (a magic number) and then
the driver has to echo that same barker to ack reception
(echo/ack). Then the device does a final ack by sending an ACK barker.

The first time this happens, we don't know ahead of time with barker
the device is going to send, as different device models and SKUs will
send different barker depending on the EEPROM programming.

If the device has sent the barker before the driver has been able to
read it, the driver looses, as it doesn't know which barker it has to
echo/ack back. With older devices, we tried a couple of combinations
and that always worked; but now, with adding support for more, in
which we have an unlimited number of new barkers, that is not an
option.

So we rework said case so that when the device gets stuck, we just
cycle through all the known types until one forces the device to send
an ack. Otherwise, the driver gives up and aborts.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The i2400m firmware loader is given a list of firmware files to try to
load by the probe() function (which can be different based on the
device's model / generation).

Current code didn't attempt to load, check and try to boot with each
file, but just to try to load if off disk. This is limiting in some
cases, where we might want to try to load a firmware and if it fails
to load onto the device, just fall back to another one.

This changes the behaviour so all files are tried for being loaded
from disk, checked and uploaded to the device until one suceeds in
bringing the device up.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

This modifies the bootrom initialization code of the i2400m driver so
it can more easily support upcoming hardware.

Currently, the code detects two types of barkers (magic numbers) sent
by the device to indicate the types of firmware it would take (signed
vs non-signed).

This schema is extended so that multiple reboot barkers are
recognized; upcoming hw will expose more types barkers which will have
to match a header in the firmware image before we can load it.

For that, a barker database is introduced; the first time the device
sends a barker, it is matched in the database. That gives the driver
the information needed to decide how to upload the firmware and which
types of firmware to use. The database can be populated from module
parameters.

The execution flow is not altered; a new function
(i2400m_is_boot_barker) is introduced to determine in the RX path if
the device has sent a boot barker. This function is becoming heavier,
so it is put away from the hot reception path [this is why there is
some reorganization in sdio-rx.c:i2400ms_rx and
usb-notifc.c:i2400mu_notification_grok()].

The documentation on the process has also been updated.

All these modifications are heavily based on previous work by Dirk
Brandewie <dirk.brandewie@intel.com>.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The i2400m based devices can boot two main types of firmware images:
signed and non-signed. Signed images have signature data included that
must match that of a certificate stored in the device.

Currently the code is making the decission on what type of firmware
load (signed vs non-signed) is going to be loaded based on a hardcoded
decission in __i2400m_ack_verify(), based on the barker the device
sent upon boot.

This is not flexible enough as future hardware will emit more barkers;
thus the bit has to be set in a place where there is better knowledge
of what is going on. This will be done in follow-up commits -- however
this patch paves the way for it.

So the querying of the mode is packed into i2400m_boot_is_signed();
the main changes are just using i2400m_boot_is_signed() to determine
the method to follow and setting i2400m->sboot in
i2400m_is_boot_barker(). The modifications in i2400m_dnload_init() and
i2400m_dnload_finalize() are just reorganizing the order of the if
blocks and thus look larger than they really are.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The kernel's %zd modifier does not really work. Use %ld (has to cast
ssize_t to long).
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Add "debug" module options to all the wimax modules (including
drivers) so that the debug levels can be set upon kernel boot or
module load time.

This is needed as currently there was a limitation where the debug
levels could only be set when a device was succesfully
enumerated. This made it difficult to debug issues that made a device
not probe properly.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The i2400m driver was missing the definition for the sysfs debug
level, which is declared in debug-levels.h.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

In the Intel Wireless Multicomm 3200, the initialization is
orchestrated by a component called Top. This component also monitors
how many times a function is reset (via sdio_disable) to detect
possible issues and will reset the whole multifunction device if any
function triggers a maximum reset level.

During WiMAX's probe, the driver needs to wait for Top to come up
before it can enable the WiMAX function. If it cannot, it will return
-ENODEV and the Top driver will rescan the SDIO bus once done
loading.

Currently, the WiMAX SDIO probe routine was trying a few times before
returning -ENODEV, and this was triggering Top's too-many-resets
detector. This is, in any case, unnecessary because the Top driver will
force the bus rescan when the functions can be probed successfully.

Added then a maxtries argument to i2400ms_enable_func() and set it to
1 when calling from probe. We want to reuse this function instead of
flat calling out sdio_enable_func() to take advantage of hardware
quirk workarounds.
Reported-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

In kernel 2.6.31, the firmware requested to ram could be marked
with read only attribute, and we can't write any thing directly
to the memory when setting up the last JUMP brh cmd.

Changed so that the scratch buffer is used.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Because some underlying bus APIs (like USB) don't like data buffers in
the stack or vmalloced areas, the i2400m driver provides a scratch
buffer (i2400m->bm_cmd_buf) for said low-level drivers to copy command
data to before passing it to said API. This is only used during boot
mode.

However, at some the code was copying the buffer even when the command
was already specified in said buffer. This is ok, but it needs to be
more careful. As thus, change so that:

(a) the copy happens only if command buffer is not the scratch buffer

(b) use memmove() in case there is overlapping
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

In order to avoid issues during high-load traffic, the interrupt
status register has to be cleared ONLY after the RX size is read.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Newer generations of the i2400m USB WiMAX device use a different
endpoint map; in order to make it easy to support it, we make the
endpoint-to-function mapeable instead of static.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

When trying to enable the iwmc3200 WiMAX SDIO function, we loop
waiting for the top controller to be up and running (at which point we
can succesfully enable the function). Between each try we wait for
I2400MS_INIT_SLEEP_INTERVAL ms.

Integration tests have found the current value of 10ms to be too
short; it was upped to 100ms to give more time to the top controller
to be ready.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

In the iwmc3200, disabling the WiMAX SDIO function when enable fails
would possibly result in a device reset triggered by the iwmc3200's
top controller since it monitors the bus reset activities from each
SDIO function. In any case, the disable makes no sense; if the enable
fails, it should not be disabled.

Thus we remove the unecessary sdio_disable_func() in
i2400ms_enable_function().
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The default SDIO IOE wait timeout returned from iwmc3200-wimax's CCCR
is not efficient. This inefficiency will actually cause problems on
Moorestown platforms (system hang).

This is a sillicon bug that requires a software patch to by
overwritting func->enable_timeout. The new value I2400MS_IOR_TIMEOUT
is recommended and verified from the system integration results.

Future sillicon releases will have this default value corrected in the
future.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

In i2400m-based devices, the driver's bootloader will retry to load
the firmware when things go wrong. The driver currently has a constant
(I2400M_BOOT_RETRIES) which governs the max number of tries.

However, different SKUs of the same hardware may admit or require
different numbers of retries due to it's particulars, so it is made a
BUS specific parameter and different values are assigned for 5x50
devices versus the 3200 ones.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The change to the SDIO boot mode RX chain could try to use the cmd and
ack buffers befor they were allocated.  USB does not have the problem
but both were changed for consistency's sake.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Fixing comments from original cut and paste error
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Add minimal ethtool support for carrier detection.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Fix misplaced parenthesis
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Ensure that index `status' remains within ms_to_errno[]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The WiMAX stack assumes that all WiMAX devices are SW OFF when they
are initialized. The recent changes in the RFKILL stack thus cause an
initial call after rfkill_register(), because by default, rfkill
considers devices to be SW ON upon registration.

So call rfkill_init_sw_state() to set it to SW OFF so
rfkill_register() doesn't do that unnecessary step.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

i2400ms_bus_bm_wait_for_ack() causes a race condition. It happens
because this function clears i2400ms->bm_ack_size before waiting for
an interrupt, which is set by the interrupt service routine i2400ms_rx()
to indicate reception and size of received data; thus, if the interrupt
came right before the clearing/waiting, it is lost.

The fix is clear the bm_ack_size to -EINPROGRESS before we are enabling
the RX interrupt configuration in i2400ms_rx_setup(). Then everytime
when the interrupt service routine i2400ms_rx() is invoked during bootmode,
bm_ack_size is updated with the actual rx_size and it is cleared to
-EINPROGRESS again after the RX data is handled.
Signed-off-by: NCindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

This patch removes an unneeded power management primitive.
Power management is automatically enabled as probe ends.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The last users of skb_icv_walk are converted to ahash now,
so skb_icv_walk is unused and can be removed.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ah4 and ah6 are converted to ahash now, so we can remove the
code for the obsolete hash algorithm.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts ah6 to the new ahash interface.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts ah4 to the new ahash interface.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support for ahash algorithms, we add a pointer to a
crypto_ahash to ah_data.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- skb_kill_datagram() can increment sk->sk_drops itself, not callers.

- UDP on IPV4 & IPV6 dropped frames (because of bad checksum or policy checks) increment sk_drops
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.

Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)

This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. GENL_MIN_ID is a valid id -> no need to start at
   GENL_MIN_ID + 1.
2. Avoid going through the ids two times: If we start at
   GENL_MIN_ID+1 (*or bigger*) and all ids are over!, the
   code iterates through the list twice (*or lesser*).
3. Simplify code - no need to start at idx=0 which gets
   reset to GENL_MIN_ID.

Patch on net-next-2.6. Reboot test shows that first id
passed to genl_register_family was 16, next two were
GENL_ID_GENERATE and genl_generate_id returned 17 & 18
(user level testing of same code shows expected values
across entire range of MIN/MAX).
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

genl_register_family() doesn't need to call genl_family_find_byid
when GENL_ID_GENERATE is passed during register.

Patch on net-next-2.6, compile and reboot testing only.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The xmit handler doesn't need to wake the queue after stopping
it temporarily (some other drivers are doing the same).

Patch on net-next-2.6, multiple netperf sessions tested.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Group device now cleanly reacts to failures during channel start and
implements a clean rollback.
Signed-off-by: NEinar Lueck <elelueck@de.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The creation of a new lcs device requires a call to the function
ccw_device_set_online() for the read and the write channel. Failure
of either call should terminate the lcs device creation immediately
with return code -ENODEV.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Timer_list structure in lcs_send_lancmd() is allocated on stack.
Initialization with init_timer() leads to above ODEBUG message.
Instead use init_timer_on_stack() which prevents above msg.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>