Some RV100 cards with 2 VGA ports show up with DVI+VGA, however
some boards with DVI+VGA have the same subsystem ids. Better
to have a VGA port show up as DVI than having a non-useable
DVI port.

reported by DHR in irc.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28745Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Tested-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DRM / radeon / KMS: Fix hibernation regression related to radeon PM (was: Re: [Regression, post-2.6.34] Hibernation broken on machines with radeon/KMS and r300)

There is a regression from 2.6.34 related to the recent radeon power
management changes, caused by attempting to cancel a delayed work
item that's never been scheduled.  However, the code as is has some
other issues potentially leading to visible problems.

First, the mutex around cancel_delayed_work() in radeon_pm_suspend()
doesn't really serve any purpose, because cancel_delayed_work() only
tries to delete the work's timer.  Moreover, it doesn't prevent the
work handler from running, so the handler can do some wrong things if
it wins the race and in that case it will rearm itself to do some
more wrong things going forward.  So, I think it's better to wait for
the handler to return in case it's already been queued up for
execution.  Also, it should be prevented from rearming itself in that
case.

Second, in radeon_set_pm_method() the cancel_delayed_work() is not
sufficient to prevent the work handler from running and queing up
itself for the next run (the failure scenario is that
cancel_delayed_work() returns 0, so the handler is run, it waits on
the mutex and then rearms itself after the mutex has been released),
so again the work handler should be prevented from rearming itself in
that case..

Finally, there's a potential deadlock in radeon_pm_fini(), because
cancel_delayed_work_sync() is called under rdev->pm.mutex, but the
work handler tries to acquire the same mutex (if it wins the race).

Fix the issues described above.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table.  Check both and make sure
we have a value system memory clock value.

v2: make sure rs690_pm_info is called on rs780/rs880 as well.

fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Tested-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

For some reason on resume, executing the BIOS scripts locks up the whole chipset, by avoiding the dynclk table the machine resumes properly and seems to function okay.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

They don't have an atombios so don't attempt to use it for
eng/mem clocks.

Reported by spoonb on #radeon
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28671Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

HDP non surface should cover the whole VRAM but we were misscomputing
the size and we endup in some case not covering the VRAM at all (if
VRAM size were > 1G). Covering more than the VRAM size shouldn't be
an issue.

Fix : https://bugs.freedesktop.org/show_bug.cgi?id=28016

[airlied: add evergreen fix]
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Should fix fdo bug 28331:
https://bugs.freedesktop.org/show_bug.cgi?id=28331Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Since the VGA switcheroo, we'd attempt to read the BIOS from VRAM on startup
but on some unposted cards this can cause hangs/crashes.

Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=28592

(further problem pointed out by agd5f on IGP systems)

Reported-by: Reilithion on #radeon
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We were returning 0 in both the success and failure paths. Noticed while
investigating FDO bug 26403.
Signed-off-by: NMatt Turner <mattst88@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This needs similar handling to other compressed textures.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=26428

Signed-off-by: sroland@vmware.com
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Code did not handle projected 2d and depth coordinates, meaning potentially
set 3d or cube special handling might stick.
(Not sure what depth coord actually does, but I guess handling it
like a normal coordinate is the right thing to do.)
Might be related to https://bugs.freedesktop.org/show_bug.cgi?id=26428

Signed-off-by: sroland@vmware.com
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28459

agd5f: apply to r1xx/r2xx as well.
Signed-off-by: NRoland Scheidegger <sroland@vmware.com>
Cc: stable@kernel.org
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This works well enough on a js21, but it would be nice if IBM could supply
more tables for the later Power6/7 machines.
Signed-off-by: NDave Airlie <airlied@redhat.com>

The transmitter needs to be enabled before the link is trained.
Reported-By: NLars Doelle <lars.doelle@on-line.de>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When suspending, we turn the display hw off, at resume the screen will stay black.
This patch turn it on. Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16180Signed-off-by: NCedric Godin <cedric.godin@skynet.be>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes fdo bug 27529:
https://bugs.freedesktop.org/show_bug.cgi?id=27529

Reported-by: steckdenis@yahoo.fr
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Installing 2.6.34 on a Power5/rn50 combo machine, X showed buggy sw rendering,
enabling tiling in the DDX fixed it. Investigation showed that a further /16
was needed in the untiled case on this chipset. Need further investigations
on what other chips this could affect, possibly rv100->rv280.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Plugged in FireMV with the rv250 on it, and the second crtc/dac didn't work,
we were reading/writing different registers than we were modifying in the code.
Signed-off-by: NDave Airlie <airlied@redhat.com>

So when we added output polling, we'd suddenly use this code more often, and the fact that it always takes over crtc2 and messes with it during probing isn't what we really want to be happening. A more complete fix would to change it to use whatever crtc was free at the time, but for now lets stay simple and just don't poll if crtc2 is already in use.

Although a more correct fix was found I suspect we should do this as well, until we get a chance to readdres the tv out polling issues.
Reported-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We really don't want to be polling tv-out but since we weren't forcing the
i2c lines to invalid (tv-out has no DDC), we were adding tv connectors to the
polling setup and this was causing blinking on secondary displays.

This fixes the regression Torsten reported.
Reported-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

debug only

agd5f: rebased
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

agd5f: rebased
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This fixes FDO bug #28375, it's kind of regression, so quite important to have
it for .35.

V2: Fix on RV770+ as well. All other chipsets have only one clock mode per
state.

V3: I'm out of luck today. Grepped for voltage in r*.c and missed evergreen.

agd5f: rebased
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

track the current voltage level and avoid setting it
if the requested voltage is already set.

v2: check voltage type before checking current voltage
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The vddc value in the power tables is not an actual voltage
like on discrete r6xx/r7xx/evergreen systems, but instead has
a symbolic meaning (e.g., NONE, LOW, HIGH, etc.).  See atombios.h

Most RS780/RS880 vbioses don't have a SetVoltage table anyway,
so it shouldn't be doing anything to the hardware at the moment.

I need to figure out how voltage is supposed to work on the newer
IGPs; until then, disable it.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I forgot to fix this in 8e36ed00Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds an additional profile, mid, to the pm profile
code which takes the place of the old low profile.  The default
behavior remains the same, e.g., auto profile now selects between
mid and high profiles based on power source, however, you can now
manually force the low profile which was previously only available
as a dpms off state.  Enabling the low profile when the displays
are on has been known to cause display corruption in some cases.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- don't rest the power state in pm_init()
We already boot up to the default power state.  Note this
patch relies on:
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
To make sure the default power state matches the boot up state.

- In the pm resume path asic init will have set the power state
back to the default so reset the tracking state values.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Noticed by Rafał Miłecki.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is needed to enable accel in the ddx.  However,
due to a bug in older versions of the ddx, it relies
on accel being disabled in order to load properly on
evergreen chips.  To maintain compatility, we add a new
get accel param and call that from the ddx.  The old one
always returns false for evergreen cards.

[this fixes a regression with older userspaces on newer kernels].
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

PM attemps to unmap objects that aren't actually mapped into userspace ever,
so just don't bother unmapping them at this point, since all you are doing
is nothing. We should be making sure all access to these objects are locked in
kernel space instead. In theory the VRAM gart table is already done, and both
the shaders and stolen vga memory blocks are never accessed at runtime.

fixes: https://bugzilla.kernel.org/show_bug.cgi?id=16127Reported-by: NJure Repnic <jlp.bugs@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.

I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The default power state does not always match the default clocks and voltage
for a particular card.  The information in the firmware info table is correct
and should be used in preference to the info the default power state.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>