This patch replaces the 'branch to setup()' instructions embedded
in the PROCINFO structs with the offset to that setup function
relative to the base of the struct. This preserves the position
independent nature of that field, but uses a data item rather
than an instruction.

This is mainly done to prevent linker failures on large kernels,
where the setup function is out of reach for the branch.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARMv6 and greater introduced a new instruction ("bx") which can be used
to return from function calls.  Recent CPUs perform better when the
"bx lr" instruction is used rather than the "mov pc, lr" instruction,
and this sequence is strongly recommended to be used by the ARM
architecture manual (section A.4.1.1).

We provide a new macro "ret" with all its variants for the condition
code which will resolve to the appropriate instruction.

Rather than doing this piecemeal, and miss some instances, change all
the "mov pc" instances to use the new macro, with the exception of
the "movs" instruction and the kprobes code.  This allows us to detect
the "mov pc, lr" case and fix it up - and also gives us the possibility
of deploying this for other registers depending on the CPU selection.
Reported-by: NWill Deacon <will.deacon@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com> # Tegra Jetson TK1
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> # mioa701_bootresume.S
Tested-by: Andrew Lunn <andrew@lunn.ch> # Kirkwood
Tested-by: NShawn Guo <shawn.guo@freescale.com>
Tested-by: Tony Lindgren <tony@atomide.com> # OMAPs
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> # Armada XP, 375, 385
Acked-by: Sekhar Nori <nsekhar@ti.com> # DaVinci
Acked-by: Christoffer Dall <christoffer.dall@linaro.org> # kvm/hyp
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> # PXA3xx
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> # Xen
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # ARMv7M
Tested-by: Simon Horman <horms+renesas@verge.net.au> # Shmobile
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit  -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings.  In any case, they are temporary and harmless.

This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code.  It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.

[1] https://lkml.org/lkml/2013/5/20/589

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

ARM v7 architecture introduced the concept of cache levels and related
control registers. New processors like A7 and A15 embed an L2 unified cache
controller that becomes part of the cache level hierarchy. Some operations in
the kernel like cpu_suspend and __cpu_disable do not require a flush of the
entire cache hierarchy to DRAM but just the cache levels belonging to the
Level of Unification Inner Shareable (LoUIS), which in most of ARM v7 systems
correspond to L1.

The current cache flushing API used in cpu_suspend and __cpu_disable,
flush_cache_all(), ends up flushing the whole cache hierarchy since for
v7 it cleans and invalidates all cache levels up to Level of Coherency
(LoC) which cripples system performance when used in hot paths like hotplug
and cpuidle.

Therefore a new kernel cache maintenance API must be added to cope with
latest ARM system requirements.

This patch adds flush_cache_louis() to the ARM kernel cache maintenance API.

This function cleans and invalidates all data cache levels up to the
Level of Unification Inner Shareable (LoUIS) and invalidates the instruction
cache for processors that support it (> v7).

This patch also creates an alias of the cache LoUIS function to flush_kern_all
for all processor versions prior to v7, so that the current cache flushing
behaviour is unchanged for those processors.

v7 cache maintenance code implements a cache LoUIS function that cleans and
invalidates the D-cache up to LoUIS and invalidates the I-cache, according
to the new API.
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>

The cacheflush syscall can fail for two reasons:

(1) The arguments are invalid (nonsensical address range or no VMA)

(2) The region generates a translation fault on a VIPT or PIPT cache

This patch allows do_cache_op to return an error code to userspace in
the case of the above. The various coherent_user_range implementations
are modified to return 0 in the case of VIVT caches or -EFAULT in the
case of an abort on v6/v7 cores.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The CPU reset functions disable the MMU and therefore must be executed
with an identity mapping in place.

This patch places the CPU reset functions into the .idmap.text section,
causing the idmap code to include them as part of the identity mapping.
Acked-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Signed-off-by: NDave Martin <dave.martin@linaro.org>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

This adds core support for saving and restoring CPU coprocessor
registers for suspend/resume support.  This contains support for suspend
with ARM920, ARM926, SA11x0, PXA25x, PXA27x, PXA3xx, V6 and V7 CPUs.
Tested on Assabet and Tegra 2.
Tested-by: NColin Cross <ccross@android.com>
Tested-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 81d11955 ("ARM: 6405/1: Handle __flush_icache_all for
CONFIG_SMP_ON_UP") added a new function to struct cpu_cache_fns:
flush_icache_all(). It also implemented this for v6 and v7 but not
for v5 and backwards. Without the function pointer in place, we
will be calling wrong cache functions.

For example with ep93xx we get following:

    Unable to handle kernel paging request at virtual address ee070f38
    pgd = c0004000
    [ee070f38] *pgd=00000000
    Internal error: Oops: 80000005 [#1] PREEMPT
    last sysfs file:
    Modules linked in:
    CPU: 0    Not tainted  (2.6.36+ #1)
    PC is at 0xee070f38
    LR is at __dma_alloc+0x11c/0x2d0
    pc : [<ee070f38>]    lr : [<c0032c8c>]    psr: 60000013
    sp : c581bde0  ip : 00000000  fp : c0472000
    r10: c0472000  r9 : 000000d0  r8 : 00020000
    r7 : 0001ffff  r6 : 00000000  r5 : c0472400  r4 : c5980000
    r3 : c03ab7e0  r2 : 00000000  r1 : c59a0000  r0 : c5980000
    Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
    Control: c000717f  Table: c0004000  DAC: 00000017
    Process swapper (pid: 1, stack limit = 0xc581a270)
    [<c0032c8c>] (__dma_alloc+0x11c/0x2d0)
    [<c0032e5c>] (dma_alloc_writecombine+0x1c/0x24)
    [<c0204148>] (ep93xx_pcm_preallocate_dma_buffer+0x44/0x60)
    [<c02041c0>] (ep93xx_pcm_new+0x5c/0x88)
    [<c01ff188>] (snd_soc_instantiate_cards+0x8a8/0xbc0)
    [<c01ff59c>] (soc_probe+0xfc/0x134)
    [<c01adafc>] (platform_drv_probe+0x18/0x1c)
    [<c01acca4>] (driver_probe_device+0xb0/0x16c)
    [<c01ac284>] (bus_for_each_drv+0x48/0x84)
    [<c01ace90>] (device_attach+0x50/0x68)
    [<c01ac0f8>] (bus_probe_device+0x24/0x44)
    [<c01aad7c>] (device_add+0x2fc/0x44c)
    [<c01adfa8>] (platform_device_add+0x104/0x15c)
    [<c0015eb8>] (simone_init+0x60/0x94)
    [<c0021410>] (do_one_initcall+0xd0/0x1a4)

__dma_alloc() calls (inlined) __dma_alloc_buffer() which ends up
calling dmac_flush_range(). Now since the entries in the
arm920_cache_fns are shifted by one, we jump into address 0xee070f38
which is actually next instruction after the arm920_cache_fns
structure.

So implement flush_icache_all() for the rest of the supported CPUs
using a generic 'invalidate I cache' instruction.
Signed-off-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When hotplug CPU is enabled, we need to keep the list of supported CPUs,
their setup functions, and __lookup_processor_type in place so that we
can find and initialize secondary CPUs.  Move these into the __CPUINIT
section.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

All implementations of cpu_proc_fin() start by disabling interrupts
and then flush caches.  Rather than have every processors proc_fin()
implementation do this, move it out into generic code - and move the
cache flush past setup_mm_for_reboot() (so it can benefit from having
caches still enabled.)

This allows cpu_proc_fin() to become independent of the L1/L2 cache
types, and eventually move the L2 cache flushing into the L2 support
code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

These are now unused, and so can be removed.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-By: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-By: NSantosh Shilimkar <santosh.shilimkar@ti.com>

... and rename the function since it no longer operates on just
pages.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Instruction fault status register, IFSR, was introduced on ARMv6 to
provide status information about the last insturction fault. It
needed for proper prefetch abort handling.

Now we have three prefetch abort model:

  * legacy - for CPUs before ARMv6. They doesn't provide neither
    IFSR nor IFAR. We simulate IFSR with section translation fault
    status for them to generalize code;
  * ARMv6 - provides IFSR, but not IFAR;
  * ARMv7 - provides both IFSR and IFAR.
Signed-off-by: NKirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

asm code really wants asm/hwcap.h, so include that instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are actually only four separate implementations of set_pte_ext.
Use assembler macros to insert code for these into the proc-*.S files.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The proc-*.S files have the _prefetch_abort pointer placed at the end
of the processor structure but the cpu-multi32.h defines it in the
second position. The patch also fixes the support for XSC3 and the
MMU-less CPUs (740, 7tdmi, 940, 946 and 9tdmi).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds a prefetch abort handler similar to the data abort one
and renames the latter for consistency. Initial implementation by Paul
Brook with some renaming by Catalin Marinas.
Signed-off-by: NPaul Brook <paul@codesourcery.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

L_PTE_ASID is not really required to be stored in every PTE, since we
can identify it via the address passed to set_pte_at().  So, create
set_pte_ext() which takes the address of the PTE to set, the Linux
PTE value, and the additional CPU PTE bits which aren't encoded in
the Linux PTE value.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

These files want to provide/access ELF hwcap information, so should
be including asm/elf.h rather than asm/procinfo.h
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

On some CPUs, bit 4 of section mappings means "update the
cache when written to".  On others, this bit is required to
be one, and others it's required to be zero.  Finally, on
ARMv6 and above, setting it turns on "no execute" and prevents
speculative prefetches.

With all these combinations, no one value fits all CPUs, so we
have to pick a value depending on the CPU type, and the area
we're mapping.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Most MMU-based CPUs have a restriction on the setting of the data cache
enable and mmu enable bits in the control register, whereby if the data
cache is enabled, the MMU must also be enabled.  Enabling the data
cache without the MMU is an invalid combination.

However, there are CPUs where the data cache can be enabled without the
MMU.

In order to allow these CPUs to take advantage of that, provide a
method whereby each proc-*.S file defines the control regsiter value
for use with nommu (with the MMU disabled.)  Later on, when we add
support for enabling the MMU on these devices, we can adjust the
"crval" macro to also enable the data cache for nommu.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The "id(wb)BRR" suffix reports which CPU debugging options were (or
were not) selected at kernel build time.  Rather than have every
proc-*.S file implement this, report the control register value,
from which this information can be deduced.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In noMMU mode, various of functions which are defined in mm/proc-*.S
is not valid or needed to be avoided. i.g. switch_mm is not needed,
just returns and this makes the I & D caches are valid which shows
great improvement of performance including task switching and IPC.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The `make buildcheck` is erroneously reporting that the .proc.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Delete obsoleted stuff from arch Makefile and rename
constants.h to asm-offsets.h
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!