Add "extcon" and "vbus-supply" properties of DWC3 node.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ADS7846 touchscreen support.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add DT support for Startek KD050C LCD 800x480 panel.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add DSS related pinmux and display data nodes required to support HDMI
and DVI video out on CM-T54.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the IO chain reconfigure fixed, we can now enable the PMIC
scripts for LDP.

Note that at least on my es3.0 based LDP, the UART seems to be
flakey after wake-up events from off-idle and hangs but eventually
continues.
Signed-off-by: NTony Lindgren <tony@atomide.com>

As we have support for this in board-rx51-peripherals.c, let's
add it to the .dts files too.

Note that the reset GPIO will eventually go to the driver.
For now let's just pull it down and skip any further reset
in case the bootloader has configured the MAC address so
NFSroot works.

Also note that after 3430-sdp are using proper GPMC timings
we can remove the tests for smsc,lan91c94 in gpmc.c.
Signed-off-by: NTony Lindgren <tony@atomide.com>

There are external pulls on these lines and enabling the
internal pulls can cause issue. This is because the internal
pulls are parallel with the external pulls. So let's clear
the internal I2C pulls.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This is no longer needed as the device specific wake-up event
can now be specified with interrupts-extended property where
the second interrupt is the pinctrl-single register, such as
the UART3 RX pin.

Note that twl4030_omap3.dtsi needs to set WAKEUPENABLE for
off-idle to properly trigger the PMIC scripts. And GPIO pins
still need to set WAKEUPENABLE for wake-up events.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Compared to legacy booting, we don't have wake-up events enabled
for device tree based booting. This means that if deeper idle
states are enabled, the device won't wake up to UART events and
seems like it has hung.

Let's fix that by adding the wake-up interrupt. Note that we
don't need to set the PIN_OFF_WAKEUPENABLE any longer, that's
handled by the wake-up interrupt when the serial driver does
request_irq on it.

Tested with the following on omap3-overo-summit that has the
ES2.1 omap:

#!/bin/bash

uarts=$(find /sys/class/tty/ttyO*/device/power/ -type d)
for uart in $uarts; do
        echo 3000 > $uart/autosuspend_delay_ms
done

uarts=$(find /sys/class/tty/ttyO*/power/ -type d)
for uart in $uarts; do
        echo enabled > $uart/wakeup
        echo auto > $uart/control
done

echo 1 > /sys/kernel/debug/pm_debug/enable_off_mode

# grep -i uart /proc/interrupts
 90:       1085      INTC  74  OMAP UART2
338:          5   pinctrl 366  OMAP UART2

# grep ^core_pwrdm /sys/kernel/debug/pm_debug/count
core_pwrdm (ON),OFF:1654,RET:131,INA:39,ON:1825...
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sub-mailbox devices are added to the Mailbox DT nodes on
OMAP2420, OMAP2430, OMAP3, AM33xx, AM43xx, OMAP4 and OMAP5
family of SoCs. This data represents the same mailboxes that
used to be represented in hwmod attribute data previously.
The node name is chosen based on the .name field of
omap_mbox_dev_info structure used in the hwmod data.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Mark rxd as wakeupcapable for 115200n8 no hardware-flow control
configuration. If h/w flow control is being used, then rts/cts
appropriately should be used.
Signed-off-by: NNishanth Menon <nm@ti.com>

We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee17 ("pinctrl: single: Add support for wake-up interrupts")
that recently got merged. In addition to that we also needed
commit 79d97015 ("of/irq: create interrupts-extended property")
that's now also merged.

Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.
Signed-off-by: NNishanth Menon <nm@ti.com>

Now that ti,am437-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.

While at it, mark the pinctrl as interrupt controller so that it can
be used with interrupts-extended property for wakeup events.
Signed-off-by: NNishanth Menon <nm@ti.com>

Now that ti,dra7-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.

While at it, mark pinctrl as interrupt controller so that it can be used
with interrupts-extended property for wakeup events.
Signed-off-by: NNishanth Menon <nm@ti.com>

Now that ti,omap5-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.

While at it, mark pinctrl as interrupt controller so that it can be
used with interrupts-extended property for wakeup events.
Signed-off-by: NNishanth Menon <nm@ti.com>

Add regulator-name properties for the regulators that don't have them,
allowing the kernel to display the name from the schematic rather than
the name of the regulator on the PMIC in order to improve diagnostics.
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

CM-T54 CoM can be used with various custom baseboards, other
than SB-T54 (supplied with SBC-T54 single board computer).

Update model property of SBC-T54 DT to clarify this.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The RFBI node for OMAP DSS was left out when adding the rest of the DSS
nodes, because it was not clear how to set up the clocks for the RFBI.

However, it seems that if there is a HWMOD for a device, we also need a
DT node for it. Otherwise, at boot, we get:

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2542 _init+0x464/0x4e0()
omap_hwmod: dss_rfbi: doesn't have mpu register target base

Now that v3.17-rc3 contains a fix 8fd46439 ("ARM: dts:
omap54xx-clocks: Fix the l3 and l4 clock rates") for the L3 ICLK
required by the RFBI, let's add the RFBI node to get rid of the
warning.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated description per comments from Nishant]
Signed-off-by: NTony Lindgren <tony@atomide.com>

These baseboards are equipped with the Technexion TAO35030 SOM. So
they include this dtsi. The common parts are extracted into an "common"
dtsi file. The main difference between both boards is, that the *lcd
has DSS support enabled for the LCD.

Some HEAD acoustics specific features are:

- LED handling
- Special FPGA/DSP audio driver (not included in this series)
- powerdown GPIO
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This baseboard is equipped with the Technexion TAO35030 SOM. So
includes this dtsi. Some Thunder specific features are:

- LCD panel
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Technexion TAO3530 is a OMAP3530 based SOM. This patch adds the
basic support for it as an dtsi file which can be included by
baseboard equipped with this SOM. E.g. the Technexion Thunder
baseboard.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Set internal clock source for MMC2 on tao3530.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM57xx processor family are variants of DRA7 family of processors and
targetted at industrial and non-automotive applications.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DRA72x-evm uses TPS65917 PMIC. Add the node.

NOTE: LDO2 is actually unused, but the usage if any is expected to be
between 1.8 to 3.3v IO voltage. So define the node.

NOTE: Interrupt used is crossbar number based.
Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I2C1 bus is used for the following peripherals
	P8 connector (MLB)
	TLV320AIC3106 Audio codec
	J15 LCD header
	24WC256 eeprom
	TMP102AIDRLT temperature sensor
	PCF8575 GPIO expander
	PCA9306 i2c voltage translator -> Goes to P9 for comm interface
	P2 expansion connector
	TPS65917 PMIC

The slowest speed of all the peripherals seems to be 400KHz.
Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: NAlex Shi <alex.shi@linaro.org>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

New system call depends on crypto.  As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.

But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto.  Remove that dependency.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 43fef47f (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.

This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678a (ARM: dts:
Revert enabling of twl configuration for n900).

Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.

This allows us to enable the PMIC configuration for n900.

Fixes: 43fef47f (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)

Cc: stable@vger.kernel.org # v3.16
Signed-off-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.

Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.

Fixes: d904b38d ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Use the corresponding compatibles to identify the devices.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit af040ffc ("ARM: make it easier to check the CPU part number
correctly") changed ARM_CPU_PART_X masks, and the way they are returned and
checked against. Usage of read_cpuid_part_number() is now deprecated, and
calling places updated accordingly. This actually broke cpuidle-big_little
initialization, as bl_idle_driver_init() performs a check using an hardcoded
mask on cpu_id.

Create an interface to perform the check (that is now even easier to read).
Define also a proper mask (ARM_CPU_PART_MASK) that makes this kind of checks
cleaner and helps preventing bugs in the future. Update usage accordingly.
Signed-off-by: NJuri Lelli <juri.lelli@arm.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may
falsely trigger a watchpoint exception, leading to potential data aborts
during exception return and/or livelock.

This patch resolves the issue in the following ways:

  - Replacing our uses of CLREX with a dummy STREX sequence instead (as
    we did for v6 CPUs).

  - Removing the clrex code from v7_exit_coherency_flush and derivatives,
    since this only exists as a minor performance improvement when
    non-cached exclusives are in use (Linux doesn't use these).

Benchmarking on a variety of ARM cores revealed no measurable
performance difference with this change applied, so the change is
performed unconditionally and no new Kconfig entry is added.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:

  - We clear the monitors on every exception return since commit
    200b812d ("Clear the exclusive monitor when returning from an
    exception"), so this is not necessary to ensure the monitors are
    cleared before returning from a fault handler.

  - Any dummy STREX will target a temporary scratch area in memory, and
    may succeed or fail without corrupting useful data. Its status value
    will not be used.

  - Any other STREX in the kernel must be preceded by an LDREX, which
    will initialise the monitors consistently and will not depend on the
    earlier state of the monitors.

Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.

This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Kernel module build with GCOV profiling fails to load with the
following error:

 $ insmod test_module.ko
   test_module: unknown relocation: 38
   insmod: can't insert 'test_module.ko': invalid module format

This happens because constructor pointers in the .init_array section
have not supported R_ARM_TARGET1 relocation type.

Documentation (ELF for the ARM Architecture) says:
    "The relocation must be processed either in the same way as R_ARM_REL32 or
     as R_ARM_ABS32: a virtual platform must specify which method is used."

Since kernel expects to see absolute addresses in .init_array R_ARM_TARGET1
relocation type should be treated the same way as R_ARM_ABS32.
Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is important for the MicroSOM implementation due to the
following details -

1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
   PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).

In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Reported-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There were several issues (of varying degree of importance) pointed out
with this code late in the review cycle, yet the code was still merged.
Let's rip it out for now and look at resubmitting at a later time.

This reverts most of commit 4fbe66d9.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.

My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.

In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.

So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: NTony Lindgren <tony@atomide.com>