Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.

Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.

Supported Chipsets:
 -QCA988X/QCA9887 PCI
 -QCA99X0/QCA9984/QCA9888/QCA4019 PCI
 -QCA6174/QCA9377 PCI/USB/SDIO
 -WCN3990 SNOC

Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds firmware crash memory dump support for QCA9888 and QCA99X0.

Tested on:

QCA9888 firmware 10.4-3.5.3-00053
QCA99X0 firmware 10.4.1.00030-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use the BIT() macro from 'linux/bitops.h' to define the rx desc
bit flags to have consistency with new definitions.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For some reason not all entries used ATH10K_FW_DIR so fix that. No functional
changes.
Signed-off-by: NMarcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Variable buf_len and num_vdev_stats are being assigned but never read.
These are redundant and can be remove.
Signed-off-by: NKenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath10k_mac_tx_push_txq returns either a postive integer (length) on
success or a negative error code on error.

The "if (ret) break;" statement will thus always break out of the loop
immediately after ath10k_mac_tx_push_txq has returned (making the loop
pointless).

A side effect of this fix is that we will iterate the queue until
ath10k_mac_tx_push_txq returns -ENOENT. This will make sure the queue is
not added back to ar->txqs when it is empty. This could potentially
improve performance somewhat (I have seen a small improvement with SDIO
devices).
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.

Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To enable thermal throttling for QCA6174 and QCA9377,
implement gen_pdev_set_quiet_mode for them.
With this change, quiet period for QCA6174/QCA9377 can
be also set/get via debugfs.
Usage:
To set quiet period:
 echo <period> > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
To get the current quiet period:
 cat /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period

This change has been verified with
QCA6174 hw3.2(fw: WLAN_RM.4.4.1-00102-QCARMSWP-1).
Signed-off-by: NYu Wang <yyuwang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Jump to the correct label in error handling path.
At this point of execution create_singlethread_workqueue() has succeeded,
so it should be properly destroyed.

Jump label was renamed in commit ec2c64e2 ("ath10k: sdio: fix memory
leak for probe allocations").
However, the bug was originally introduced in commit d96db25d
("ath10k: add initial SDIO support").

Fixes: d96db25d ("ath10k: add initial SDIO support")
Signed-off-by: NNiklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in ath10k_warn warning message text
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When attempt to read tpc_stats for the chipsets which support
more than 3 tx chain will trigger kernel panic(kernel stack is corrupted)
due to writing values on rate_code array out of range.
This patch changes the array size depends on the WMI_TPC_TX_N_CHAIN and
added check to avoid write values on the array if the num tx chain
get in tpc config event is greater than WMI_TPC_TX_N_CHAIN.

Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00057

Kernel panic log :

[  323.510944] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: bf90c654
[  323.510944]
[  323.524390] CPU: 0 PID: 1908 Comm: cat Not tainted 3.14.77 #31
[  323.530224] [<c021db48>] (unwind_backtrace) from [<c021ac08>] (show_stack+0x10/0x14)
[  323.537941] [<c021ac08>] (show_stack) from [<c03c53c0>] (dump_stack+0x80/0xa0)
[  323.545146] [<c03c53c0>] (dump_stack) from [<c022e4ac>] (panic+0x84/0x1e4)
[  323.552000] [<c022e4ac>] (panic) from [<c022e61c>] (__stack_chk_fail+0x10/0x14)
[  323.559350] [<c022e61c>] (__stack_chk_fail) from [<bf90c654>] (ath10k_wmi_event_pdev_tpc_config+0x424/0x438 [ath10k_core])
[  323.570471] [<bf90c654>] (ath10k_wmi_event_pdev_tpc_config [ath10k_core]) from [<bf90d800>] (ath10k_wmi_10_4_op_rx+0x2f0/0x39c [ath10k_core])
[  323.583047] [<bf90d800>] (ath10k_wmi_10_4_op_rx [ath10k_core]) from [<bf8fcc18>] (ath10k_htc_rx_completion_handler+0x170/0x1a0 [ath10k_core])
[  323.595702] [<bf8fcc18>] (ath10k_htc_rx_completion_handler [ath10k_core]) from [<bf961f44>] (ath10k_pci_hif_send_complete_check+0x1f0/0x220 [ath10k_pci])
[  323.609421] [<bf961f44>] (ath10k_pci_hif_send_complete_check [ath10k_pci]) from [<bf96562c>] (ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci])
[  323.622490] [<bf96562c>] (ath10k_ce_per_engine_service [ath10k_pci]) from [<bf9656f0>] (ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci])
[  323.635423] [<bf9656f0>] (ath10k_ce_per_engine_service_any [ath10k_pci]) from [<bf96365c>] (ath10k_pci_napi_poll+0x44/0xe8 [ath10k_pci])
[  323.647665] [<bf96365c>] (ath10k_pci_napi_poll [ath10k_pci]) from [<c0599994>] (net_rx_action+0xac/0x160)
[  323.657208] [<c0599994>] (net_rx_action) from [<c02324a4>] (__do_softirq+0x104/0x294)
[  323.665017] [<c02324a4>] (__do_softirq) from [<c0232920>] (irq_exit+0x9c/0x11c)
[  323.672314] [<c0232920>] (irq_exit) from [<c0217fc0>] (handle_IRQ+0x6c/0x90)
[  323.679341] [<c0217fc0>] (handle_IRQ) from [<c02084e0>] (gic_handle_irq+0x3c/0x60)
[  323.686893] [<c02084e0>] (gic_handle_irq) from [<c02095c0>] (__irq_svc+0x40/0x70)
[  323.694349] Exception stack(0xdd489c58 to 0xdd489ca0)
[  323.699384] 9c40:                                                       00000000 a0000013
[  323.707547] 9c60: 00000000 dc4bce40 60000013 ddc1d800 dd488000 00000990 00000000 c085c800
[  323.715707] 9c80: 00000000 dd489d44 0000092d dd489ca0 c026e664 c026e668 60000013 ffffffff
[  323.723877] [<c02095c0>] (__irq_svc) from [<c026e668>] (rcu_note_context_switch+0x170/0x184)
[  323.732298] [<c026e668>] (rcu_note_context_switch) from [<c020e928>] (__schedule+0x50/0x4d4)
[  323.740716] [<c020e928>] (__schedule) from [<c020e490>] (schedule_timeout+0x148/0x178)
[  323.748611] [<c020e490>] (schedule_timeout) from [<c020f804>] (wait_for_common+0x114/0x154)
[  323.756972] [<c020f804>] (wait_for_common) from [<bf8f6ef0>] (ath10k_tpc_stats_open+0xc8/0x340 [ath10k_core])
[  323.766873] [<bf8f6ef0>] (ath10k_tpc_stats_open [ath10k_core]) from [<c02bb598>] (do_dentry_open+0x1ac/0x274)
[  323.776741] [<c02bb598>] (do_dentry_open) from [<c02c838c>] (do_last+0x8c0/0xb08)
[  323.784201] [<c02c838c>] (do_last) from [<c02c87e4>] (path_openat+0x210/0x598)
[  323.791408] [<c02c87e4>] (path_openat) from [<c02c9d1c>] (do_filp_open+0x2c/0x78)
[  323.798873] [<c02c9d1c>] (do_filp_open) from [<c02bc85c>] (do_sys_open+0x114/0x1b4)
[  323.806509] [<c02bc85c>] (do_sys_open) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
[  323.814241] CPU1: stopping
[  323.816927] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.77 #31
[  323.823008] [<c021db48>] (unwind_backtrace) from [<c021ac08>] (show_stack+0x10/0x14)
[  323.830731] [<c021ac08>] (show_stack) from [<c03c53c0>] (dump_stack+0x80/0xa0)
[  323.837934] [<c03c53c0>] (dump_stack) from [<c021cfac>] (handle_IPI+0xb8/0x140)
[  323.845224] [<c021cfac>] (handle_IPI) from [<c02084fc>] (gic_handle_irq+0x58/0x60)
[  323.852774] [<c02084fc>] (gic_handle_irq) from [<c02095c0>] (__irq_svc+0x40/0x70)
[  323.860233] Exception stack(0xdd499fa0 to 0xdd499fe8)
[  323.865273] 9fa0: ffffffed 00000000 1d3c9000 00000000 dd498000 dd498030 10c0387d c08b62c8
[  323.873432] 9fc0: 4220406a 512f04d0 00000000 00000000 00000001 dd499fe8 c021838c c0218390
[  323.881588] 9fe0: 60000013 ffffffff
[  323.885070] [<c02095c0>] (__irq_svc) from [<c0218390>] (arch_cpu_idle+0x30/0x50)
[  323.892454] [<c0218390>] (arch_cpu_idle) from [<c026500c>] (cpu_startup_entry+0xa4/0x108)
[  323.900690] [<c026500c>] (cpu_startup_entry) from [<422085a4>] (0x422085a4)
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

During write to some of debugfs in ath10k, few variables exposing stack
data when process user input. which leads to possible information leak.

This patch fix this issue by initializing buffer and checks
the return valure of 'simple_write_to_buffer'.
Signed-off-by: NVenkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.

To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.

Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wcn3990 supports shadow register for ce write.

Add a hw param for shadow register support.
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).

Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When trying to set wow wakeup patterns it fails with this command:

iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx

The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.

Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.

Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: NAlan Liu <alanliu@codeaurora.org>
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

FW path is mapped incorrectly for the WCN3990
hw version. Fix fw path with correct hw1.0 name.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Added for the same reason as the TX wrappers.
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These wrappers makes the HTT ops align better with the HIF ops
(where similar wrappers are used).

It also makes it easier for a target to have unsupported ops
(by letting the corresponding function pointer be NULL).
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

commit f2593cb1 ("ath10k: Search SMBIOS for OEM board file
extension") added a feature to ath10k that allows Board Data File
(BDF) conflicts between multiple devices that use the same device IDs
but have different calibration requirements to be resolved by allowing
a "variant" string to be stored in SMBIOS [and later device tree, added
by commit d06f26c5 ("ath10k: search DT for qcom,ath10k-calibration-
variant")] that gets appended to the ID stored in board-2.bin.

This original patch had a regression, however. Namely that devices with
a variant present in SMBIOS that didn't need custom BDFs could no longer
find the default BDF, which has no variant appended. The patch was
reverted and re-applied with a fix for this issue in commit 1657b8f8
("search SMBIOS for OEM board file extension").

But the fix to fall back to a default BDF introduced another issue: the
driver currently parses IEs in board-2.bin one by one, and for each one
it first checks to see if it matches the ID with the variant appended.
If it doesn't, it checks to see if it matches the "fallback" ID with no
variant. If a matching BDF is found at any point during this search, the
search is terminated and that BDF is used. The issue is that it's very
possible (and is currently the case for board-2.bin files present in the
ath10k-firmware repository) for the default BDF to occur in an earlier
IE than the variant-specific BDF. In this case, the current code will
happily choose the default BDF even though a better-matching BDF is
present later in the file.

This patch fixes the issue by first searching the entire file for the ID
with variant, and searching for the fallback ID only if that search
fails. It also includes some code cleanup in the area, as
ath10k_core_fetch_board_data_api_n() no longer does its own string
mangling to remove the variant from an ID, instead leaving that job to a
new flag passed to ath10k_core_create_board_name().

I've tested this patch on a QCA4019 and verified that the driver behaves
correctly for 1) both fallback and variant BDFs present, 2) only fallback
BDF present, and 3) no matching BDFs present.

Fixes: 1657b8f8 ("ath10k: search SMBIOS for OEM board file extension")
Signed-off-by: NThomas Hebb <tommyhebb@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fix a typo in the function ath10k_wmi_set_wmm_param().
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Correct a minor bug in the commit 0628467f ("ath10k: fix
copy engine 5 destination ring stuck") which introduced a change to fix
firmware assert that happens when ring indices of copy engine 5 are stuck
for a specific duration, problem with this fix is that it did not use
ring arithmatic. As a result,firmware asserts did not go away entirely
athough the frequency of occurrence has reduced. Using ring arithmatic
to fix the issue.

Tested on QCA9984(fw version-10.4-3.4-00082).

Fixes: 0628467f ("ath10k: fix copy engine 5 destination ring stuck)
Signed-off-by: NManikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add clock and regulator votes for WCN3990 WLAN
chipset.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 has interrupts per CE and the interrupt summary
is not retained after the interrupt handler has finished
execution. We need to check if we received any
ce in rx and tx completion path.

Generate a interrupt summary with all CE interrupts if
the target does not retain interrupt summary after the
execution of interrupt handler.
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wcn3990 does not use bmi.
Add support to get target info from hif ops.
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change type of hif sg tx paddr to dma_addr_t for
supporting target having addressing mode greater than
32 bit.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add hif rx methods in rx path for wcn3990
target.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add hif tx/tx-complete methods for wcn3990
target.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add hif power-up/power-down methods for wcn3990
target.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add mapping of HTC endpoint services supported
by wcn3990 target to tx/rx pipe.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 target uses 3 Copy engine(CE1/CE9/CE10) in RX path
and CE 11 for pktlog.
Add data path HTC ep services and PKTLOG services for WCN3990.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add hif start/stop callback for allocating/freeing buffers
on tx/rx pipe and enabling/disabling the tx/rx pipe
interrupts.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add methods for resource(memory, irq, HOST CE config)
initialization and de-initialization for WCN3990 target.

WCN3990 target uses 12 copy engine and following CE config.

[CE0] :host->target control and raw streams
[CE1] :target->host HTT
[CE2] :target->host WMI
[CE3] :host->target WMI
[CE4] :host->target HTT
[CE5] :reserved
[CE6] :Target autonomous HIF_memcpy
[CE7] :reserved
[CE8] :reserved
[CE9] :target->host HTT
[CE10] :target->host HTT
[CE11] :target -> host PKTLOG
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 is integrated 802.11ac chipset with SNOC
bus interface. Add snoc layer driver registration
and associated ops.

WCN3990 support is not yet complete as cold-boot
handshake is done using qmi(Qualcomm-MSM-Interface)
and qmi client support will be added once qmi framework
is available.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

CE layer is shared between pci and snoc target and results
in duplicate object inclusion if both modules are compiled
together statically and undefined KBUILD_MODNAME if
compiled as module.

Fix this by building ce layer in ath10k core module by
adding ce object inclusion with ATH10K_CE boolean CONFIG.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.

hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: NVenkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>