DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.

For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.

The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove two unused WB functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch changes the current omapdss driver to fill a dispc_ops struct
and set it to omapdss-base.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and  dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.

Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.

This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Let's disable all scaling that requires horizontal decimation with
higher factor than 4, until we have better estimates of what we can
and can not do. However, NV12 color format appears to work Ok with
all decimation factors.

When decimating horizontally by more that 4 the dss is not able to
fetch the data in burst mode. When this happens it is hard to tell if
there enough bandwidth. Despite what theory says this appears to be
true also for 16-bit color formats.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omapdrm DSS manager enable/disable operations check the DSS manager
state to avoid double enabling/disabling. Check the CRTC software state
instead to decrease the dependency of the DRM layer to the DSS layer.
The dispc_mgr_is_enabled() function then be turned into a static
function, but needs to be moved up in its compilation unit to avoid a
forward declaration.

Add a WARN_ON to catch double enable or disable that should be prevented
by the DRM core and would be a clear sign of a bug. The warning should
eventually be removed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use 'vm' to refer to a struct videomode instead of 'p', 't', 'timings' or
something else.

The code will be easier to follow if we use consistent names.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.

This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_video_timings struct have the same members as struct videomode, but
their types are different. As first step change the types of the
omap_video_timings struct members to match their counterpart in
struct videomode to catch any type cast related issues.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for sync edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for pixel data edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for double_pixel mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for DE level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for h/vsync level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of passing the omap_video_timings structure's members individually,
use the pointer to the struct.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove the interlace member and add display_flags to omap_video_timings to
configure the interlace mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vbp member to vback_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vfp member to vfront_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vsw member to vsync_len.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hbp member to hback_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hfp member to hfront_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hsw member to hsync_len.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the y_res member to vactive.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the x_res member to hactive.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Found with scripts/coccinelle/misc/boolconv.cocci.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Workaround for errata i734 in DSS dispc
 - LCD1 Gamma Correction Is Not Working When GFX Pipe Is Disabled

For gamma tables to work on LCD1 the GFX plane has to be used at least
once after DSS HW has come out of reset. The workaround sets up a
minimal LCD setup with GFX plane and waits for one vertical sync irq
before disabling the setup and continuing with the context
restore. The physical outputs are gated during the operation.

For details see:
OMAP543x Multimedia Device Silicon Revision 2.0 Silicon Errata
Literature Number: SWPZ037E
Or some other relevant errata document for the DSS IP version.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add gamma table support to DSS dispc.

DSS driver initializes the default gamma table at component bind time
and holds a copy of all gamma tables in its internal data structure.

Each call to dispc_mgr_set_gamma() updates the internal table and
triggers write to the HW, if it is enabled. The tables are restored to
HW in PM resume callback. The drivers internal data structure match
the HW tables in size and in number of significant bits per color
component. The dispc_mgr_set_gamma() converts the size of any given
table for the internal data structure using linear interpolation.
Default gamma table is restored if NULL is given in place of gamma
lut.

dispc_mgr_gamma_size() gives HW gamma table size for the channel and
returns 0 if gamma table is not supported by the HW or the DSS driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>

With the new PLL helpers, we can clean up the dispc_fclk_rate(). This
will also make dispc_fclk_rate() support clock sources it didn't support
earlier.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

With the new PLL helpers, we can clean up the dispc_mgr_lclk_rate().
This will also make dispc_mgr_lclk_rate() support clock sources it
didn't support earlier.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The names of the enum dss_clk_source's values are legacy names, only
correct for OMAP3 DSS. Rename the names to more generic ones.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that there is no "non-generic" version of the function to get the
clock source name, lets rename dss_get_generic_clk_source_name() to
dss_get_clk_source_name().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have two functions to return a name for clock sources for debugging
purposes: dss_feat_get_clk_source_name() and
dss_get_generic_clk_source_name().

The former is supposed to return a DSS IP version specific name for the
clock source, and the latter is supposed to return a more generic name.

All this seems a bit pointless, so let's remove the former one.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

'enum omap_dss_clk_source' is internal to dss. Let's rename it to
'dss_clk_source' match our naming convention.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dispc_ovl_check() is not used anywhere, so it can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have removed all the uses of compat code from omapdrm and the
non-compat parts of omapdss, so now we can remove all the compat code
itself.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing the use of the 'struct omap_overlay_manager' from
omapdrm, and one part of that is removing the use of
mgr->supported_outputs field.

This patch adds dispc_mgr_get_supported_outputs() function which can be
used instead of mgr->supported_outputs. omap_crtc.c is changed to use
the new function.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Interlace field order is different between VENC and HDMI. The driver
currently sets the field order for VENC.

This patch adds the code to set the field order for HDMI.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to DISPC to output double-pixel mode.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>