Since the driver has been split into MFD there is no reason for it to
stay, so remove it.
Signed-off-by: NKsenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for sixteen-channel 12-bit resolution ADC and its functions,
which include general-purpose ADC readings, battery voltage measurement,
and die temperature measurement.
Signed-off-by: NKsenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.

The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets (see [0] and [1]), as well as by reading (various versions
of) the vendor driver and by inspecting the registers on the vendor
kernels of my testing-hardware.

Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.

Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
  accuracy of the results - in my tests the results were less than 3%
  off without calibration compared to the vendor driver). Adding support
  for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
  Adding support for this is probably not so easy since (based on the
  u-boot sources) most SoC versions are using different registers and
  algorithms for the conversion from "ADC value" to temperature.

Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
  buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
  individually because otherwise the ADC would be drawing power
  constantly)
- interrupt support (similar to the vendor driver this new driver is
  polling the results. It is unclear if the IRQ-mode is supported on
  older (Meson6 or Meson8) hardware as well or if there are any errata)

[0]
http://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
[1] http://dn.odroid.com/S905/DataSheet/S905_Public_Datasheet_V1.1.4.pdfSigned-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add IIO driver for the Renesas RCar GyroADC block. This block is a
simple 4/8-channel ADC which samples 12/15/24 bits of data every
cycle from all channels.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add iio driver for Maxim MAX11100 single-channel ADC.
Signed-off-by: NJacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.

The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)

The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.
Signed-off-by: NAndreas Klinger <ak@it-klinger.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.
Signed-off-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds support for STMicroelectronics STM32 MCU's analog to
digital converter.
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add core driver for STMicroelectronics STM32 ADC (Analog to Digital
Converter). STM32 ADC can be composed of up to 3 ADCs with shared
resources like clock prescaler, common interrupt line and analog
reference voltage.
This core driver basically manages shared resources.
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
                          _
                         | \
    input +------>-------|+ \
                         |   \
           .-------.     |    }---.
           |       |     |   /    |
           |    dac|-->--|- /     |
           |       |     |_/      |
           |       |              |
           |       |              |
           |    irq|------<-------'
           |       |
           '-------'
Signed-off-by: NPeter Rosin <peda@axentia.se>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.

In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.

Datasheets:
	http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdf
	http://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdfSigned-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.

Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.

This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.

The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver.  I have tested with the ADC12138.  The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.

The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.
Signed-off-by: NAlison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add Mediatek auxadc driver based on iio.
It will register a device in iio and support iio.
So thermal can read auxadc channel to sample data by iio device.
It is tested successfully on mt2701 platform.
Mt8173 and mt6577 platforms are not tested.
But the expectation is compatible.
Signed-off-by: NZhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add support for Texas Instruments ADC141S626, and ADC161S626 chips.
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds basic driver implementation for Broadcom's
static adc controller used in iProc SoC's family.
Signed-off-by: NRaveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add base support for the 10-bit SAR ADC peripheral found
on NXP LPC18xx/43xx SoCs.

This is a minimal driver that does not support burst mode,
interrupts, DMA or hardware triggers.

User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The driver has sysfs readings with runtime PM support for power saving.
It also offers buffer support that can be used together with IIO software
triggers.

Datasheet can be found here:
	http://www.ti.com.cn/cn/lit/ds/symlink/ads1015.pdfSigned-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.

The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Move mxs-lradc driver from drivers/staging/iio/adc to drivers/iio/adc.
Signed-off-by: NKsenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds ADC0831/ADC0832/ADC0834/ADC0838 8-bit ADC driver.
I have tested with ADC0831 and ADC0832.  The remaining ADC0834 and
ADC0838 are very similar to ADC0832.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This driver supports the new version of the Atmel ADC device introduced
with the SAMA5D2 SoC family.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Freescale i.MX7D soc contains a new ADC IP. This patch add this ADC
driver support, and the driver only support ADC software trigger.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

in SOFTWARE buffer mode, a kthread will capture the active scan_elements
into a kfifo, then compute the remaining time until the next capture tick
and do an active wait (udelay).

This will produce a stream of up to fours channels plus a 64bits
timestamps (ns).

Tested with ina226, on BeagleBoneBlack.

Datasheet: http://www.ti.com/lit/gpn/ina226Signed-off-by: NMarc Titinger <mtitinger@baylibre.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds support for the Texas Intruments ADS8688 ADC.
Signed-off-by: NSean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: NMartin Hundebøll <martin.hundeboll@prevas.dk>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This driver code was found as:

https://android.googlesource.com/kernel/tegra/+/aaabb2e045f31e5a970109ffdaae900dd403d17e/drivers/staging/iio/adc

Fixed various compilation issues and test this driver on omap5 evm.
Signed-off-by: NPradeep Goudagunta <pgoudagunta@nvidia.com>
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NJonathan Cameron <jic23@kernel.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add Holt threshold detector driver for HI-8435 chip
Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Move the entry for the CC 10001 ADC driver in Kconfig and Makefile up to
maintain alphabetic order.
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds the support of the Berlin ADC, available on Berlin SoCs.
This ADC has 8 channels available, with one connected to a temperature
sensor.

The particularity here, is that the temperature sensor connected to the
ADC has its own registers, and both the ADC and the temperature sensor
must be configured when using it.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds support for DA9150 Charger & Fuel-Gauge IC GPADC.
Signed-off-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: NHartmut Knaack <knaack.h@gmx.de>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

This commit adds support for Cosmic Circuits 10001 10-bit ADC device.
Reviewed-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NPhani Movva <Phani.Movva@imgtec.com>
Signed-off-by: NNaidu Tellapati <Naidu.Tellapati@imgtec.com>
[ezequiel: code style cleaning]
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
15bits resolution and register space inside PMIC accessible across
SPMI bus.

The vadc driver registers itself through IIO interface.
Signed-off-by: NStanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
16 bits resolution and register space inside PMIC accessible across
SPMI bus.

The driver registers itself through IIO interface.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Platform driver for X-Powers AXP288 ADC, which is a sub-device of the
customized AXP288 PMIC for Intel Baytrail-CR platforms. GPADC device
enumerates as one of the MFD cell devices. It uses IIO infrastructure
to communicate with userspace and consumer drivers.

Usages of ADC channels include battery charging and thermal sensors.

Based on initial work by:
Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The ADC is a 3-channel signal-ended 10-bit Successive Approximation
Register (SAR) A/D Converter. It uses the supply and ground as its reference
and converts the analog input signal into 10-bit binary digital codes.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds support for ADC128S052 from TI.
Signed-off-by: NAngelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The ad7291 driver is in a reasonable shape. It does not use non-standard API/ABI
and there are no major style issues with the driver. So this patch moves it out
of staging.

There is one small warning from checkpatch which is also fixed in this patch.
The patch also sorts the #include directives in alphabetical order.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This driver add partial support of the
maxim 1027/1029/1031. Differential mode is not
supported.

It was tested on armadeus apf27 board.
Signed-off-by: NPhilippe Reynes <tremyfr@yahoo.fr>
Reviewed-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>