There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Polling SDIO_CCCR_INTx could create a fake interrupt with Marvell
SD8797 card. Add a quirk to handle this case. The fixup here is
to issue a dummy CMD52 read to function 0 register 0xff, and this
dummy read must be right after SDIO_CCCR_INTx is read.

Patch has been verified on a dw_mmc controller (Samsung Chromebook)
with MMC_CAP_SDIO_IRQ disabled.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Reviewed-by: NPaul Stewart <pstew@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

These two basic defines were everywhere, simply because module.h
was also everywhere.   But we are cleaning up the latter.  So make
the exporters actually call out their need for the include.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.

This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NUlf HANSSON <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The wl12xx device supports disconnecting the pull-up resistor on
CD/DAT[3] (pin 1) of the card.

Tell SDIO core to disconnect that resistor during card init,
since we don't need it at that point (and anyway all
hosts shall provide pull-up resistors on all data lines DAT[3:0]
as described in section 6 of the SD physical specification).

As a result, this may save some power, but it's also generally healthy
since it prevents both ends from pulling up that pin, which
results in undesirable asymmetric physical bus.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Tell SDIO core to ignore the standard SDIO function interface
codes indicated by the wl1271. This is required because the
wl1271 erroneously indicates its first function as a standard
Bluetooth SDIO interface, and that drives btsdio mad.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This sdio card supports having its sdio clock shutdown.
It is also not using the SDIO IRQ, but rather uses a side gpio irq.
Signed-off-by: NPierre Tardy <tardyp@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.

To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: NPierre Tardy <tardyp@gmail.com>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.

So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk.  We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.
Signed-off-by: NPierre Tardy <pierre.tardy@intel.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>