The GMA500 GPU driver uses GEM shmem objects, but with a new twist: the
backing RAM has to be below 4GB.  Not a problem while the boards
supported only 4GB: but now Intel's D2700MUD boards support 8GB, and
their GMA3600 is managed by the GMA500 driver.

shmem/tmpfs has never pretended to support hardware restrictions on the
backing memory, but it might have appeared to do so before v3.1, and
even now it works fine until a page is swapped out then back in.  When
read_cache_page_gfp() supplied a freshly allocated page for copy, that
compensated for whatever choice might have been made by earlier swapin
readahead; but swapoff was likely to destroy the illusion.

We'd like to continue to support GMA500, so now add a new
shmem_should_replace_page() check on the zone when about to move a page
from swapcache to filecache (in swapin and swapoff cases), with
shmem_replace_page() to allocate and substitute a suitable page (given
gma500/gem.c's mapping_set_gfp_mask GFP_KERNEL | __GFP_DMA32).

This does involve a minor extension to mem_cgroup_replace_page_cache()
(the page may or may not have already been charged); and I've removed a
comment and call to mem_cgroup_uncharge_cache_page(), which in fact is
always a no-op while PageSwapCache.

Also removed optimization of an unlikely path in shmem_getpage_gfp(),
now that we need to check PageSwapCache more carefully (a racing caller
might already have made the copy).  And at one point shmem_unuse_inode()
needs to use the hitherto private page_swapcount(), to guard against
racing with inode eviction.

It would make sense to extend shmem_should_replace_page(), to cover
cpuset and NUMA mempolicy restrictions too, but set that aside for now:
needs a cleanup of shmem mempolicy handling, and more testing, and ought
to handle swap faults in do_swap_page() as well as shmem.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephane Marchesin <marcheu@chromium.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <rob.clark@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Acked-by: NSerge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>

After we moved inode_sync_wait() from end_writeback() it doesn't make sense
to call the function end_writeback() anymore. Rename it to clear_inode()
which well says what the function really does - set I_CLEAR flag.
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>

Adds to generic xattr support introduced in Linux 3.0 by implementing
initxattrs callback.  This enables consulting of security attributes from
LSM and EVM when inode is created.

[hughd@google.com: moved under CONFIG_TMPFS_XATTR, with memcpy in shmem_xattr_alloc]
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@intel.com>
Reviewed-by: NJames Morris <james.l.morris@oracle.com>
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NCong Wang <amwang@redhat.com>

Collapse security_vm_enough_memory() variants into a single function.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJames Morris <jmorris@namei.org>

Commit cc39c6a9 ("mm: account skipped entries to avoid looping in
find_get_pages") correctly fixed an infinite loop; but left a problem
that find_get_pages() on shmem would return 0 (appearing to callers to
mean end of tree) when it meets a run of nr_pages swap entries.

The only uses of find_get_pages() on shmem are via pagevec_lookup(),
called from invalidate_mapping_pages(), and from shmctl SHM_UNLOCK's
scan_mapping_unevictable_pages().  The first is already commented, and
not worth worrying about; but the second can leave pages on the
Unevictable list after an unusual sequence of swapping and locking.

Fix that by using shmem_find_get_pages_and_swap() (then ignoring the
swap) instead of pagevec_lookup().

But I don't want to contaminate vmscan.c with shmem internals, nor
shmem.c with LRU locking.  So move scan_mapping_unevictable_pages() into
shmem.c, renaming it shmem_unlock_mapping(); and rename
check_move_unevictable_page() to check_move_unevictable_pages(), looping
down an array of pages, oftentimes under the same lock.

Leave out the "rotate unevictable list" block: that's a leftover from
when this was used for /proc/sys/vm/scan_unevictable_pages, whose flawed
handling involved looking at pages at tail of LRU.

Was there significance to the sequence first ClearPageUnevictable, then
test page_evictable, then SetPageUnevictable here? I think not, we're
under LRU lock, and have no barriers between those.
Signed-off-by: NHugh Dickins <hughd@google.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: <stable@vger.kernel.org> [back to 3.1 but will need respins]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

scan_mapping_unevictable_pages() is used to make SysV SHM_LOCKed pages
evictable again once the shared memory is unlocked.  It does this with
pagevec_lookup()s across the whole object (which might occupy most of
memory), and takes 300ms to unlock 7GB here.  A cond_resched() every
PAGEVEC_SIZE pages would be good.

However, KOSAKI-san points out that this is called under shmem.c's
info->lock, and it's also under shm.c's shm_lock(), both spinlocks.
There is no strong reason for that: we need to take these pages off the
unevictable list soonish, but those locks are not required for it.

So move the call to scan_mapping_unevictable_pages() from shmem.c's
unlock handling up to shm.c's unlock handling.  Remove the recently
added barrier, not needed now we have spin_unlock() before the scan.

Use get_file(), with subsequent fput(), to make sure we have a reference
to mapping throughout scan_mapping_unevictable_pages(): that's something
that was previously guaranteed by the shm_lock().

Remove shmctl's lru_add_drain_all(): we don't fault in pages at SHM_LOCK
time, and we lazily discover them to be Unevictable later, so it serves
no purpose for SHM_LOCK; and serves no purpose for SHM_UNLOCK, since
pages still on pagevec are not marked Unevictable.

The original code avoided redundant rescans by checking VM_LOCKED flag
at its level: now avoid them by checking shp's SHM_LOCKED.

The original code called scan_mapping_unevictable_pages() on a locked
area at shm_destroy() time: perhaps we once had accounting cross-checks
which required that, but not now, so skip the overhead and just let
inode eviction deal with them.

Put check_move_unevictable_page() and scan_mapping_unevictable_pages()
under CONFIG_SHMEM (with stub for the TINY case when ramfs is used),
more as comment than to save space; comment them used for SHM_UNLOCK.
Signed-off-by: NHugh Dickins <hughd@google.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

vfs_create() ignores everything outside of 16bit subset of its
mode argument; switching it to umode_t is obviously equivalent
and it's the only caller of the method
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

vfs_mkdir() gets int, but immediately drops everything that might not
fit into umode_t and that's the only caller of ->mkdir()...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Seeing that just about every destructor got that INIT_LIST_HEAD() copied into
it, there is no point whatsoever keeping this INIT_LIST_HEAD in inode_init_once();
the cost of taking it into inode_init_always() will be negligible for pipes
and sockets and negative for everything else.  Not to mention the removal of
boilerplate code from ->destroy_inode() instances...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Replace direct i_nlink updates with the respective updater function
(inc_nlink, drop_nlink, clear_nlink, inode_dec_link_count).
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>

When a race between putback_lru_page() and shmem_lock with lock=0 happens,
progrom execution order is as follows, but clear_bit in processor #1 could
be reordered right before spin_unlock of processor #1.  Then, the page
would be stranded on the unevictable list.

spin_lock
SetPageLRU
spin_unlock
                                clear_bit(AS_UNEVICTABLE)
                                spin_lock
                                if PageLRU()
                                        if !test_bit(AS_UNEVICTABLE)
                                        	move evictable list
smp_mb
if !test_bit(AS_UNEVICTABLE)
        move evictable list
                                spin_unlock

But, pagevec_lookup() in scan_mapping_unevictable_pages() has
rcu_read_[un]lock() so it could protect reordering before reaching
test_bit(AS_UNEVICTABLE) on processor #1 so this problem never happens.
But it's a unexpected side effect and we should solve this problem
properly.

This patch adds a barrier after mapping_clear_unevictable.

I didn't meet this problem but just found during review.
Signed-off-by: NMinchan Kim <minchan.kim@gmail.com>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: NJohannes Weiner <jweiner@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The files changed within are only using the EXPORT_SYMBOL
macro variants.  They are not using core modular infrastructure
and hence don't need module.h but only the export.h header.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Make the radix_tree exceptional cases, mostly in filemap.c, clearer.

It's hard to devise a suitable snappy name that illuminates the use by
shmem/tmpfs for swap, while keeping filemap/pagecache/radix_tree
generality.  And akpm points out that /* radix_tree_deref_retry(page) */
comments look like calls that have been commented out for unknown
reason.

Skirt the naming difficulty by rearranging these blocks to handle the
transient radix_tree_deref_retry(page) case first; then just explain the
remaining shmem/tmpfs swap case in a comment.
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We have already acknowledged that swapoff of a tmpfs file is slower than
it was before conversion to the generic radix_tree: a little slower
there will be acceptable, if the hotter paths are faster.

But it was a shock to find swapoff of a 500MB file 20 times slower on my
laptop, taking 10 minutes; and at that rate it significantly slows down
my testing.

Now, most of that turned out to be overhead from PROVE_LOCKING and
PROVE_RCU: without those it was only 4 times slower than before; and
more realistic tests on other machines don't fare as badly.

I've tried a number of things to improve it, including tagging the swap
entries, then doing lookup by tag: I'd expected that to halve the time,
but in practice it's erratic, and often counter-productive.

The only change I've so far found to make a consistent improvement, is
to short-circuit the way we go back and forth, gang lookup packing
entries into the array supplied, then shmem scanning that array for the
target entry.  Scanning in place doubles the speed, so it's now only
twice as slow as before (or three times slower when the PROVEs are on).

So, add radix_tree_locate_item() as an expedient, once-off,
single-caller hack to do the lookup directly in place.  #ifdef it on
CONFIG_SHMEM and CONFIG_SWAP, as much to document its limited
applicability as save space in other configurations.  And, sadly,
#include sched.h for cond_resched().
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

But we've not yet removed the old swp_entry_t i_direct[16] from
shmem_inode_info.  That's because it was still being shared with the
inline symlink.  Remove it now (saving 64 or 128 bytes from shmem inode
size), and use kmemdup() for short symlinks, say, those up to 128 bytes.

I wonder why mpol_free_shared_policy() is done in shmem_destroy_inode()
rather than shmem_evict_inode(), where we usually do such freeing? I
guess it doesn't matter, and I'm not into NUMA mpol testing right now.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NPekka Enberg <penberg@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert shmem_writepage() to use shmem_delete_from_page_cache() to use
shmem_radix_tree_replace() to substitute swap entry for page pointer
atomically in the radix tree.

As with shmem_add_to_page_cache(), it's not entirely satisfactory to be
copying such code from delete_from_swap_cache, but again judged easier
to sell than making its other callers go through the extras.

Remove the toy implementation's shmem_put_swap() and shmem_get_swap(),
now unreferenced, and the hack to disable swap: it's now good to go.

The way things have worked out, info->lock no longer helps to guard the
shmem_swaplist: we increment swapped under shmem_swaplist_mutex only.
That global mutex exclusion between shmem_writepage() and shmem_unuse()
is not pretty, and we ought to find another way; but it's been forced on
us by recent race discoveries, not a consequence of this patchset.

And what has become of the WARN_ON_ONCE(1) free_swap_and_cache() if a
swap entry was found already present? That's no longer possible, the
(unknown) one inserting this page into filecache would hit the swap
entry occupying that slot.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove mem_cgroup_shmem_charge_fallback(): it was only required when we
had to move swappage to filecache with GFP_NOWAIT.

Remove the GFP_NOWAIT special case from mem_cgroup_cache_charge(), by
moving its call out from shmem_add_to_page_cache() to two of thats three
callers.  But leave it doing mem_cgroup_uncharge_cache_page() on error:
although asymmetrical, it's easier for all 3 callers to handle.

These two changes would also be appropriate if anyone were to start
using shmem_read_mapping_page_gfp() with GFP_NOWAIT.

Remove mem_cgroup_get_shmem_target(): mc_handle_file_pte() can test
radix_tree_exceptional_entry() to get what it needs for itself.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert shmem_getpage_gfp(), the engine-room of shmem, to expect page or
swap entry returned from radix tree by find_lock_page().

Whereas the repetitive old method proceeded mainly under info->lock,
dropping and repeating whenever one of the conditions needed was not
met, now we can proceed without it, leaving shmem_add_to_page_cache() to
check for a race.

This way there is no need to preallocate a page, no need for an early
radix_tree_preload(), no need for mem_cgroup_shmem_charge_fallback().

Move the error unwinding down to the bottom instead of repeating it
throughout.  ENOSPC handling is a little different from before: there is
no longer any race between find_lock_page() and finding swap, but we can
arrive at ENOSPC before calling shmem_recalc_inode(), which might
occasionally discover freed space.

Be stricter to check i_size before returning.  info->lock is used for
little but alloced, swapped, i_blocks updates.  Move i_blocks updates
out from under the max_blocks check, so even an unlimited size=0 mount
can show accurate du.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert shmem_unuse_inode() to use a lockless gang lookup of the radix
tree, searching for matching swap.

This is somewhat slower than the old method: because of repeated radix
tree descents, because of copying entries up, but probably most because
the old method noted and skipped once a vector page was cleared of swap.
Perhaps we can devise a use of radix tree tagging to achieve that later.

shmem_add_to_page_cache() uses shmem_radix_tree_replace() to compensate
for the lockless lookup by checking that the expected entry is in place,
under lock.  It is not very satisfactory to be copying this much from
add_to_page_cache_locked(), but I think easier to sell than insisting
that every caller of add_to_page_cache*() go through the extras.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Disable the toy swapping implementation in shmem_writepage() - it's hard
to support two schemes at once - and convert shmem_truncate_range() to a
lockless gang lookup of swap entries along with pages, freeing both.

Since the second loop tightens its noose until all entries of either
kind have been squeezed out (and we shall make sure that there's not an
instant when neither is visible), there is no longer a need for yet
another pass below.

shmem_radix_tree_replace() compensates for the lockless lookup by
checking that the expected entry is in place, under lock, before
replacing it.  Here it just deletes, but will be used in later patches
to substitute swap entry for page or page for swap entry.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bring truncate.c's code for truncate_inode_pages_range() inline into
shmem_truncate_range(), replacing its first call (there's a followup
call below, but leave that one, it will disappear next).

Don't play with it yet, apart from leaving out the cleancache flush, and
(importantly) the nrpages == 0 skip, and moving shmem_setattr()'s
partial page preparation into its partial page handling.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While it's at its least, make a number of boring nitpicky cleanups to
shmem.c, mostly for consistency of variable naming.  Things like "swap"
instead of "entry", "pgoff_t index" instead of "unsigned long idx".

And since everything else here is prefixed "shmem_", better change
init_tmpfs() to shmem_init().
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The maximum size of a shmem/tmpfs file has been limited by the maximum
size of its triple-indirect swap vector.  With 4kB page size, maximum
filesize was just over 2TB on a 32-bit kernel, but sadly one eighth of
that on a 64-bit kernel.  (With 8kB page size, maximum filesize was just
over 4TB on a 64-bit kernel, but 16TB on a 32-bit kernel,
MAX_LFS_FILESIZE being then more restrictive than swap vector layout.)

It's a shame that tmpfs should be more restrictive than ramfs, and this
limitation has now been noticed.  Add another level to the swap vector?
No, it became obscure and hard to maintain, once I complicated it to
make use of highmem pages nine years ago: better choose another way.

Surely, if 2.4 had had the radix tree pagecache introduced in 2.5, then
tmpfs would never have invented its own peculiar radix tree: we would
have fitted swap entries into the common radix tree instead, in much the
same way as we fit swap entries into page tables.

And why should each file have a separate radix tree for its pages and
for its swap entries? The swap entries are required precisely where and
when the pages are not.  We want to put them together in a single radix
tree: which can then avoid much of the locking which was needed to
prevent them from being exchanged underneath us.

This also avoids the waste of memory devoted to swap vectors, first in
the shmem_inode itself, then at least two more pages once a file grew
beyond 16 data pages (pages accounted by df and du, but not by memcg).
Allocated upfront, to avoid allocation when under swapping pressure, but
pure waste when CONFIG_SWAP is not set - I have never spattered around
the ifdefs to prevent that, preferring this move to sharing the common
radix tree instead.

There are three downsides to sharing the radix tree.  One, that it binds
tmpfs more tightly to the rest of mm, either requiring knowledge of swap
entries in radix tree there, or duplication of its code here in shmem.c.
I believe that the simplications and memory savings (and probable higher
performance, not yet measured) justify that.

Two, that on HIGHMEM systems with SWAP enabled, it's the lowmem radix
nodes that cannot be freed under memory pressure - whereas before it was
the less precious highmem swap vector pages that could not be freed.
I'm hoping that 64-bit has now been accessible for long enough, that the
highmem argument has grown much less persuasive.

Three, that swapoff is slower than it used to be on tmpfs files, since
it's using a simple generic mechanism not tailored to it: I find this
noticeable, and shall want to improve, but maybe nobody else will
notice.

So...  now remove most of the old swap vector code from shmem.c.  But,
for the moment, keep the simple i_direct vector of 16 pages, with simple
accessors shmem_put_swap() and shmem_get_swap(), as a toy implementation
to help mark where swap needs to be handled in subsequent patches.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

shmem_unuse_inode() and shmem_writepage() contain a little code to cope
with pages inserted independently into the filecache, probably by a
filesystem stacked on top of tmpfs, then fed to its ->readpage() or
->writepage().

Unionfs was indeed experimenting with working in that way three years ago,
but I find no current examples: nowadays the stacking filesystems use vfs
interfaces to the lower filesystem.

It's now illegal: remove most of that code, adding some WARN_ON_ONCEs.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Erez Zadok <ezk@fsl.cs.sunysb.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can now simplify shmem_getpage_gfp(): there is no longer a dilemma of
filepage passed in via shmem_readpage(), then swappage found, which must
then be copied over to it.

Although at first it's tempting to replace the **pagep arg by returning
struct page *, that makes a mess of IS_ERR_OR_NULL(page)s in all the
callers, so leave as is.

Insert BUG_ON(!PageUptodate) when we find and lock page: some of the
complication came from uninitialized pages inserted into filecache prior
to readpage; but now we're in control, and only release pagelock on
filecache once it's uptodate (if an error occurs in reading back from
swap, the page remains in swapcache, never moved to filecache).
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The prealloc_page handling in shmem_getpage_gfp() is unnecessarily
complicated: first simplify that before going on to filepage/swappage.

That's right, don't report ENOMEM when the preallocation fails: we may or
may not need the page.  But simply report ENOMEM once we find we do need
it, instead of dropping lock, repeating allocation, unwinding on failure
etc.  And leave the out label on the fast path, don't goto.

Fix something that looks like a bug but turns out not to be: set
PageSwapBacked on prealloc_page before its mem_cgroup_cache_charge(), as
the removed case was doing.  That's important before adding to LRU
(determines which LRU the page goes on), and does affect which path it
takes through memcontrol.c, but in the end MEM_CGROUP_CHANGE_TYPE_ SHMEM
is handled no differently from CACHE.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NShaohua Li <shaohua.li@intel.com>
Cc: "Zhang, Yanmin" <yanmin.zhang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove that pernicious shmem_readpage() at last: the things we needed it
for (splice, loop, sendfile, i915 GEM) are now fully taken care of by
shmem_file_splice_read() and shmem_read_mapping_page_gfp().

This removal clears the way for a simpler shmem_getpage_gfp(), since page
is never passed in; but leave most of that cleanup until after.

sys_readahead() and sys_fadvise(POSIX_FADV_WILLNEED) will now EINVAL,
instead of unexpectedly trying to read ahead on tmpfs: if that proves to
be an issue for someone, then we can either arrange for them to return
success instead, or try to implement async readahead on tmpfs.
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make shmem_getpage() a wrapper, passing mapping_gfp_mask() down to
shmem_getpage_gfp(), which in turn passes gfp down to shmem_swp_alloc().

Change shmem_read_mapping_page_gfp() to use shmem_getpage_gfp() in the
CONFIG_SHMEM case; but leave tiny !SHMEM using read_cache_page_gfp().

Add a BUG_ON() in case anyone happens to call this on a non-shmem mapping;
though we might later want to let that case route to read_cache_page_gfp().

It annoys me to have these two almost-redundant args, gfp and fault_type:
I can't find a better way; but initialize fault_type only in shmem_fault().

Note that before, read_cache_page_gfp() was allocating i915_gem's pages
with __GFP_NORETRY as intended; but the corresponding swap vector pages
got allocated without it, leaving a small possibility of OOM.
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tidy up shmem_file_splice_read():

Remove readahead: okay, we could implement shmem readahead on swap,
but have never done so before, swap being the slow exceptional path.

Use shmem_getpage() instead of find_or_create_page() plus ->readpage().

Remove several comments: sorry, I found them more distracting than
helpful, and this will not be the reference version of splice_read().
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Copy __generic_file_splice_read() and generic_file_splice_read() from
fs/splice.c to shmem_file_splice_read() in mm/shmem.c.  Make
page_cache_pipe_buf_ops and spd_release_page() accessible to it.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

2.6.36's 7e496299 ("tmpfs: make tmpfs scalable with percpu_counter for
used blocks") to make tmpfs scalable with percpu_counter used
inode->i_lock in place of sbinfo->stat_lock around i_blocks updates; but
that was adverse to scalability, and unnecessary, since info->lock is
already held there in the fast paths.

Remove those uses of i_lock, and add info->lock in the three error paths
where it's then needed across shmem_free_blocks().  It's not actually
needed across shmem_unacct_blocks(), but they're so often paired that it
looks wrong to split them apart.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace the ->check_acl method with a ->get_acl method that simply reads an
ACL from disk after having a cache miss.  This means we can replace the ACL
checking boilerplate code with a single implementation in namei.c.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This patch changes the security_inode_init_security API by adding a
filesystem specific callback to write security extended attributes.
This change is in preparation for supporting the initialization of
multiple LSM xattrs and the EVM xattr.  Initially the callback function
walks an array of xattrs, writing each xattr separately, but could be
optimized to write multiple xattrs at once.

For existing security_inode_init_security() calls, which have not yet
been converted to use the new callback function, such as those in
reiserfs and ocfs2, this patch defines security_old_inode_init_security().
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>