A previous fix had gone though and disabled relaxed ordering for Rx
descriptor read fetching.  This was not necessary as this functions
correctly and has no ill effects on the system.

In addition several of the defines used for the DCA control registers were
incorrect in that they indicated descriptor effects when they actually had
an impact on either data or header write back.  As such I have update these
to correctly reflect either DATA or HEAD.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the current logging styles.

Remove unnecessary _DEBUG_DRIVER_ and PFX, use pr_debug.
Coalesce format.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it a bit easier to do the loopback frame creating and
testing.  Previously we were doing an and to drop the last bit, and then
dividing the frame_size by 2 in order to get locations for frame bytes and
testing.  Instead we can simplify it by just shifting the register one bit
to the right and using that for the frame offsets.

This change also replaces all instances of rx_buffer_info with just
rx_buffer since that is closer to the name of the actual structure being
used and can save a few extra characters.

In addition I have updated the logic for cleaning up a test frame so that
we pass an rx_buffer instead of the sk_buff.  The main motivation behind
this is changes that will replace the sk_buff with just a page in the
future.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since there are multiple spots where we have to cycle through all of the
rings on a q_vector it makes sense to just add a function for iterating
through all of them.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes the rings a part of the q_vector directly instead of
indirectly.  Specifically on x86 systems this helps to avoid any cache
set conflicts between the q_vector, the tx_rings, and the rx_rings as the
critical stride is 4K and in order to cross that boundary you would need to
have over 15 rings on a single q_vector.

In addition this allows for smarter allocations when Flow Director is
enabled.  Previously Flow Director would set the irq_affinity hints based
on the CPU and was still using a node interleaving approach which on some
systems would end up with the two values mismatched.  With the new approach
we can set the affinity for the irq_vector and use the CPU for that
affinity to determine the node value for the node and the rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a minor cleanup to address the unnecessary use of
napi_schedule_prep in ixgbe_intr and to also remove a blank line that is
not needed since it is separating a comment from the line it is explaining.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The old code had several errors in how it was determining the vector
budget.  In order to simplify things this patch updates the code so that it
will attempt to always allocated paired Rx/Tx vectors instead of attempting
to allocate individual vectors when the number of queues is less than the
number of CPUs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change corrects an issue in which Adaptive Interrupt Moderation was
not changing values due to the fact that we were performing an and
operation on the resultant value that was causing the value to never change
from the default 20K interrupts per second.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to address the fact that the tx_itr_setting was
dropping to 0 when no separate Tx vectors were provided.  This had resulted
in the driver incorrectly configuring the Tx ring with a WTHRESH of 1 in
order to avoid Tx hangs even though that was not necessary. This change
makes it so that we instead take a look at the Tx ring's q_vector to
determine if the ring will have an ITR value less than 8us.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change moves several frequently accessed items together into one cache
line in order to reduce cache misses in the hot-path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There isn't any need to clear the status bits in the descriptors due to the
fact that the eop_desc provides enough information for us to know
that we have cleaned to the last packet that the software has put on the
ring.  The status bits are cleared as a part of putting the frame on the
ring so as long as we do not read the descriptor bit prior to reading the
value eop_desc we should be able to guarantee that we will not clean beyond
the end of the current data stream.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds a memory barrier to the byte queue limit code to address a
possible race as has been seen in the past with the
netif_stop_queue/netif_wake_queue logic.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are seeing dev_watchdog hangs on several drivers.  I suspect this is due
to the __QUEUE_STATE_STACK_XOFF bit being set prior to a reset for link
change, and then not being cleared by netdev_tx_reset_queue.  This change
corrects that.

In addition we were seeing dev_watchdog hangs on igb after running the
ethtool tests.  We found this to be due to the fact that the ethtool test
runs the same logic as ndo_start_xmit, but we were never clearing the XOFF
flag since the loopback test in ethtool does not do byte queue accounting.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds support for byte queue limits (BQL).

Based on patch from Eric Dumazet for igb.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>

As noted by Ben Hutchings and David Miller, work limits for NAPI
should not be tied to interrupt moderation parameters.  This
should be handled by NAPI, possibly through sysfs.

Neil Horman & Stephen Hemminger are working on a solution for
NAPI currently.  In the meantime, remove this tie between
work limits and interrupt moderation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>

A bug was introduced with the following patch:

  Commmit bdbc0631
  Author: Eric Dumazet <eric.dumazet@gmail.com>
  igb: Add support for byte queue limits.

The ethtool offline tests will cause a perpetual link flap, this
is because the tests also need to account for byte queue limits (BQL).

CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NJeff Pieper  <jeffrey.e.pieper@intel.com>

Previously, allocation used queue statistics directly in its calcualtion.
This change causes these calculations to be summed into the statistics,
without being affected by them.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, if autoneg failed, ethtool would return the achieved autoneg.
This patch corrects this, causing ethtool to return the requested autoneg
capabilities even if autoneg fails.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, unless both interface and link were up, ethtool returned
the requested speed/duplex when asked for the interface's settings.
This change will now enable the driver to answer correctly (i.e.,
return unknown as its answer).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change enables the FW to make more accurate decisions regarding the
active functions.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, we've used the object's function id instead of using the
input's value. This is remedied, as in other flows.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, we used a hard-coded value as paramater, instead of using the
input's value. This is now remedied, as in other flows.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These definitions are united into the header.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds an ethernet driver for the LPC32xx ARM SoC.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With this feature, a Linux guest can now configure multiple vlans through
a single synthetic NIC on Win8 Hyper-V host.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Limiting the memcpy to be the sizeof(struct rndis_message) can truncate
the message if there are Per-Packet-Info or Out-of-Band data.

In my earlier patch (commit 45326342), the unnecessary kmap_atomic and
kunmap_atomic surrounding this memcpy have been removed because the memory
in the receive buffer is always mapped. This memcpy is not necessary
either. To fix the bug, I removed the memcpy.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define pr_fmt(fmt) as appropriate.

Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".

Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.

Add missing "\n" to pr_info in gre.c.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current kernel messaging style.

Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.

Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini.  Some ah4 and esp messages
are now not prefixed with "ip ".

The intent of this patch is to later add something like
  #define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.

Text size is trivially reduced. (x86-32 allyesconfig)

$ size net/ipv4/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 887888	  31558	 249696	1169142	 11d6f6	net/ipv4/built-in.o.new
 887934	  31558	 249800	1169292	 11d78c	net/ipv4/built-in.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following 4 functions:
  move_addr_to_kernel
  move_addr_to_user
  verify_iovec
  verify_compat_iovec
are always effectively called with a sockaddr_storage.

Make this explicit by changing their signature.

This removes a large number of casts from sockaddr_storage to sockaddr.
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit d6ddef9e(IPv6: Fix not join all-router mcast group
when forwarding set.) I check 'dev' after it's dereference that
leads to a Smatch complaint:

net/ipv6/addrconf.c:438 ipv6_add_dev()
	 warn: variable dereferenced before check 'dev' (see line 432)

net/ipv6/addrconf.c
   431		/* protected by rtnl_lock */
   432		rcu_assign_pointer(dev->ip6_ptr, ndev);
                                   ^^^^^^^^^^^^
Old dereference.

   433
   434		/* Join all-node multicast group */
   435		ipv6_dev_mc_inc(dev, &in6addr_linklocal_allnodes);
   436
   437		/* Join all-router multicast group if forwarding is set
*/
   438		if (ndev->cnf.forwarding && dev && (dev->flags &
IFF_MULTICAST))
                                            ^^^

Remove the check to avoid the complaint as 'dev' can't be NULL.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLi Wei <lw@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some months ago, tglx asked me off list if I would maintain the PTP
Hardware Clock code. Since then, the code has been fully merged, and I
am actively looking after it. This patch makes it official.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch has been tested on a machine with the Realtek
RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05).

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/irda/{ali-ircc, via-ircc, w83977af-ir}.c: ensure arguments to request_irq and free_irq are compatible

Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq.  Without this
property, free_irq does nothing.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq.  Without this
property, free_irq does nothing.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Connection ID configured through RTNL must allow zero as
connection id. If connection-id is not given when creating the
interface, configure a loopback interface using ifindex as
connection-id.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kill faulty checks on flow-off leading to connection drop at race conditions.
caif_socket checks for flow-on before transmitting and goes to sleep or
return -EAGAIN upon flow stop. Remove faulty subsequent checks on flow-off
leading to connection drop. Also fix memory leaks on some of the errors paths.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>