Backport short cables support from pata_via.c.

This patch should allow UDMA > 2 modes on Acer Ferrari 3400.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

Backport short cables support from pata_sis.c.

This patch allows UDMA > 2 modes on ASUS A6K.

Thanks to testing this patch goes out to Jiri Stavinoha.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

Backport short cables support from pata_ali.c and while at it cleanup
existing cable detection code.

This patch should allow UDMA > 2 modes on HP Pavilion N5430 and Fujitsu P2000.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

Backport short cables support from ata_piix.c.

This patch should allow UDMA > 2 modes on:
- Acer 5602WLMi
- Acer 3682WLMi
- Asus W5F
- Acer Aspire 2023WLMi
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

ide-timing.h:

* remove handling of DMA modes from ide_find_best_mode() and rename it to
  ide_find_best_pio_mode()

* drop no longer needed "map" argument from ide_find_best_pio_mode()
  and delete needless ->id check

* remove no longer needed XFER_SWDMA and XFER_UDMA* defines

au1xxx-ide.c:

* use ide_max_dma_mode() instead of ide_find_best_mode()

* remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef

amd74xx.c:

* store UDMA masks in amd_ide_chip[] and while at it make "base" field
  to be u8 instead of unsigned long

* convert the driver to use UDMA masks from amd_ide_chip[]

* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
  of ide_find_best_mode()

* delete stale comment from amd74xx_ide_dma_check()

* remove no longer needed AMD_UDMA* defines

via82cxxx.c:

* remove unused DISPLAY_VIA_TIMINGS define

* store UDMA masks in via_isa_bridges[] and while at it make "flags" field
  to be u8 instead of u16

* convert the driver to use UDMA masks from via_isa_bridges[]

* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
  of ide_find_best_mode()

* remove no longer needed VIA_UDMA* defines

pmac.c:

* use ide_max_dma_mode() instead of ide_find_best_mode()

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

If the word 62 is not defined use the word 52 to get SWDMA mask
in ide_get_mode_mask().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch replaces an array size calculation in drivers/ide/legacy/hd.c
that was done using sizeof with the ARRAY_SIZE macro.

Tested by compilation on an i386 box using "allyesconfig".
Diffed against Linus' git-tree.
Signed-off-by: NAndi Drebes <lists-receive@programmierforen.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Delete the unnecessary macro ARY_LEN and use ARRAY_SIZE directly.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This removes the support to treat "ALL" as a wildcard for
firmware revision.  This is made a separate patch, as it will
break out-of-tree ide drivers that feed its own table that uses
"ALL" as the wildcard to ide_in_drive_list().
Signed-off-by: NJunio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This updates the DMA whitelist in MIPS specific au1xxx ide
driver to use NULL instead of "ALL" as the wildcard.
Signed-off-by: NJunio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Earlier, the matching of (model,rev) in ide-dma black/white list
handling was to consider "ALL" in the table to match any
revision.  This makes NULL to be also an accepted wildcard, and
changes the entries of tables in ide-dma.c to use NULL.

The code still accepts "ALL" as the wildcard, in order to keep
any out-of-tree ide driver that feeds its own table that uses
"ALL" as the wildcard to ide_in_drive_list() function from
breaking.
Signed-off-by: NJunio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There's no reason to have the speedproc() method wrapper for the two quite
different chip families, so just get rid of it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE driver uses a semaphore as mutex.
Use the mutex API instead of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

--

Get rid of the init_dma() method (which had no particular reason to exist) by
folding it into the init_hwif() method. While at it, also perform some cleanup
in the latter method:

- get rid of the useless clearing of hwif->autodma;

- fold the serialization code into one 'if' statement;

- fold setting the drives' 'autotune' and 'autodma' fields into the single
  statements...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Rework init_setup_aec6x80() so that it won't rewrite the constant name strings
anymore -- in order to do this:

- in aec62xx_init_one(), pass a local copy of 'struct pci_device_id' down the
  call chain;

- change the names for in aec62xx_chipsets[] to default to AEC-6280[R];

- override the 'name' field in init_setup_aec6x80() only if bit 4 of the DMA
  status register is set.

While at it, also change the 'udma_mask' field for AEC-6x80R chips in this
function and remove the code doing the same from the init_hwif() method...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix two minor issues with PCI0646 chip reporting in the init_chipset() method:
"IRQ workaround enabled" message printed out not only for revision 0x01 and
"CMD646: chipset revision" printed twice (by IDE core and the driver itself).
Also, remove empty/pointless switch cases for the chips other than PCI0646,
duplicate write to the MRDMODE register when enabling interrupts and MEMORY
READ LINE cycles, and needless/misplaced initialization of the timing registers
in this method.
Switch to reading only the PCI revision ID register itself, not the whole 32
bits at its address in init_chipset() and init_hwif() methods; in addition,
get rid of the useless clearing of hwif->autodma and perform some cosmetic
style changes in the latter method.
Refactor ata66_cmd64x() by moving all the code into the 'switch' statement,
renaming/adding variables, and fixing the coding style.
While at it, finally get rid of the meaningless aliasing register #define's...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Simplify UltraDMA mode filtering in the driver:

- make use of the newly introduced 'udma_mask' field of 'ide_pci_device_t' to
  set the correct hwif->ultra_mask, modifying init_setup_hpt366() to select
  the correct mask based on the chip revision;

- replace 'max_mode' field of the 'struct hpt_info' with 'max_ultra' specifying
  the maximum UltraDMA mode allowed;

- rewrite hpt3xx_udma_filter() to differ the filters based on the 'chip_type'
  field, and only use it for HPT366 and HPT370[A] where it's really necessary.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE driver uses a semaphore as mutex.
Use the mutex API instead of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:

- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;

- in au1xxx-ide.c, get rid of commented out printk();

- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:

- in aec62xx.c, rename the method in accordance with other drivers, and get rid
  of unnecessary variables there;

- in pdc202xx_old.c, define/use 'hwif' variable;

- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Switch the driver to always program DMA/PIO timings and set device transfer
mode instead of trusting BIOS on CSB6 controllers (libata pata_serverworks.c
driver is also doing things this way and there were no problems reported so
far).  While doing conversion I noticed that the old code had many issues:

* the code was assuming that hwif->dma_status is always valid
  (which obviously isn't true if hwif->dma_base == NULL)

* value of "(ultra_timing >> (4*unit)) & ~(0xF0)" expression wasn't checked
  to fit into udma_modes[5]

* code validating DMA timings didn't validate corresponding PIO timings

* extra CSB5 PIO register wasn't validated et all

* hwif->ide_dma_off_quietly() is always called before ide_set_dma() (which in
  turn calls hwif->speedproc() method - svwks_tune_chipset() in this case)
  so the code depending on DMA capable bit of DMA status to be set was never
  executed (=> the code was never validating DMA timings despite actually
  enabling DMA if the PIO timings were OK!)

* on resume driver dependend entirely on BIOS to restore timings and set
  transfer mode on the device

While at it:

There is no need to read PIO/MWDMA timings now so don't do it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
  JFS: Update print_hex_dump() syntax
  JFS: use print_hex_dump() rather than private dump_mem() function
  JFS: Whitespace cleanup and remove some dead code

add credits for recent major scheduler contributions:

  Con Kolivas, for pioneering the fair-scheduling approach
  Peter Williams, for smpnice
  Mike Galbraith, for interactivity tuning of CFS
  Srivatsa Vaddagiri, for group scheduling enhancements
Signed-off-by: NIngo Molnar <mingo@elte.hu>

micro-optimize mmdrop(). Improves schedule()'s assembly a bit.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

the Linux scheduler is starving a number of workloads. So default
to more agressive idle-balancing. This hurts lmbench context-switching
numbers (which was the main reason we sucked at idle-balancing for
such a long time) but the lmbench numbers are fine once the system is
minimally utilized.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

clean up the sleep_on() APIs:

 - do not use fastcall
 - replace fragile macro magic with proper inline functions
Signed-off-by: NIngo Molnar <mingo@elte.hu>

4 small style cleanups to sched.c: checkpatch.pl is now happy about
the totality of sched.c [ignoring false positives] - yay! ;-)
Signed-off-by: NIngo Molnar <mingo@elte.hu>

do not set softirqs to nice +19. _If_ for whatever reason
we missed to process some high-prio softirq and woke up
ksoftirqd, we should give it a fair chance to actually
get some work done, even if the system is under load.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

simplify sched_rt.c's sched_find_first_bit() function: there are
only 100 RT priority levels left.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

add Documentation/sched-design-CFS.txt
Signed-off-by: NIngo Molnar <mingo@elte.hu>

enable CONFIG_SCHED_DEBUG in lib/Kconfig.debug.

the runtime overhead of this option is very small.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

scheduler debugging core: implement /proc/sched_debug and
/proc/<PID>/sched files for scheduler debugging.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

add CFS debug sysctls: only tweakable if SCHED_DEBUG is enabled.
This allows for faster debugging of scheduler problems.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

remove the old cpu-accounting field from signal_struct, now
that the code is using CFS's stats.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

remove unused rq types from sched.c, now that we switched
over to CFS.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

batch_task() in sched.h is now unused - remove it.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

remove now-unused types/fields used by the old scheduler.
Signed-off-by: NIngo Molnar <mingo@elte.hu>