Currently, 8-bit (MMIO) and 32-bit (MMIO32) register interfaces are
supported for the 8250 console, but the 16-bit (MMIO16) is not.
The 8250 UART device on my board is connected to a 16-bit bus and
my main motivation is to use earlycon with it.
(Refer to arch/arm/boot/dts/uniphier-support-card.dtsi)
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now, wait_for_xmitr() is only called from serial_putc(), and both
are short enough.  They can be merged into a single function.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current code waits until the transmitter becomes empty,
before sending each character, and after finishing the whole string.
This seems a bit redundant.

It can be more efficient by checking the transmitter only after sending
each character.  This should be safe because the transmitter is already
empty at the first entry of serial_putc().
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The IER has already been masked in early_serial8250_setup(), there is
no reason to save and restore it every time early_serial8250_write()
is called.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 98 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Peter Hurley <peter@hurleysoftware.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 92 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 811 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This function compiles to 141 bytes of machine code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: Jiri Slaby <jslaby@suse.com>
CC: linux-serial@vger.kernel.org
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This UART driver should not depend on the console.  They should be
orthogonal.

Surround the earlycon code with CONFIG_SERIAL_EARLYCON conditional
and rip off "depends on SERIAL_8250_CONSOLE".
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

SERIAL_8250_INGENIC depends on SERIAL_8250_CONSOLE, which already
selects SERIAL_EARLYCON.

This line is redundant.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reuses the code of drivers/tty/serial/8250/8250_early.c except

  - Overwrite device->port.iotype and device->port.regshift for
    UPIO_MEM32 because of_setup_earlycon() has set them for UPIO_MEM.

  - Set device->baud to zero to prevent early8250_setup() from
    initializing the divisor register because port->uartclk does not
    match the frequency expected by this hardware.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/tty/serial/8250/Kconfig:config SERIAL_8250_MT6577
drivers/tty/serial/8250/Kconfig:        bool "Mediatek serial port support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/tty/serial/Kconfig:config SERIAL_ATMEL
drivers/tty/serial/Kconfig:     bool "AT91 / AT32 on-chip serial port support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't replace module.h with init.h since the file already has that.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that imx_mctrl_check is implemented below imx_get_mctrl the former
can call the latter directly instead of via sport->port.ops->get_mctrl.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The .get_mctrl callback should not report the status of RTS or LOOP, so
drop this. Instead implement reporting the state of CAR (aka DCD) and
RI.

For .set_mctrl implement setting the DTR line.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tested-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Signed-off-by: NLABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit replaces every instance of the string "jsm"
in the driver with JSM_DRIVER_NAME, as the two are
equivalent. This should increase overall consistency.
Signed-off-by: NGavin Thomas Claugus <gclaugus@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

fsl8250_handle_irq is now used by the of_serial driver, and that fails
if it is a loadable module:

ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined!

This exports the symbol to avoid randconfig errors.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: d43b54d2 ("serial: Enable Freescale 16550 workaround on arm")
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

8250_mid uses rational_best_approximation() function, so the
driver needs to select CONFIG_RATIONAL option.

This fixes build error when CONFIG_RATIONAL is not enabled:

drivers/built-in.o: In function `mid8250_set_termios':
8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation'
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 7d8c70d8 ("serial: mctrl-gpio: rename init function"),
crisv32 either do not build or crash as follows.

Unable to handle kernel NULL pointer dereference
Linux 4.3.0-rc7-next-20151101 #1 Sun Nov 1 11:41:28 PST 2015
...
Call Trace: [<c0004a0e>] show_stack+0x0/0x9e
[<c004c0c0>] printk+0x0/0x2c
[<c00059d4>] show_registers+0x14a/0x1c2
[<c004c0c0>] printk+0x0/0x2c
[<c0004b52>] die_if_kernel+0x7c/0x9e
[<c0005346>] do_page_fault+0x32e/0x3e6
[<c01dc59c>] of_get_property+0x0/0x2c
[<c01e0558>] of_irq_parse_raw+0x12a/0x376
[<c01dc59c>] of_get_property+0x0/0x2c
[<c0053aca>] get_page_from_freelist+0x73e/0x856
[<c01dc59c>] of_get_property+0x0/0x2c
[<c0008912>] d_mmu_refill+0x10a/0x112
[<c01b488c>] devm_kmalloc+0x40/0x56
[<c01b47d0>] add_dr+0xc/0x1c
[<c01b4800>] devm_add_action+0x2/0x4e
[<c01abdbc>] mctrl_gpio_init_noauto+0x1c/0x76
[<c01abf9e>] mctrl_gpio_init+0x22/0x110

The function call in the etraxfs-uart driver was not renamed,
possibly due to interference with commit 7b9c5162 ("serial:
etraxfs-uart: use mctrl_gpio helpers for handling modem signals").

Fixes: 7d8c70d8 ("serial: mctrl-gpio: rename init function")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NNiklas Cassel <nks@flawful.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Earlycon support for Freescale lpuart should only be enabled when
console support is enabled.

Fixes: 1d59b382 ("serial: fsl_lpuart: add earlycon support")
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the device name when registering an interrupt so that multiple
ports don't all have the same interrupt name.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The implementation of mux_console_device() is very similar to
uart_console_device(). Setting .data field in mux_console then we can
convert to use uart_console_device().
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NHelge Deller <deller@gmx.de>

The UART_DUMMY_DR_RX status bit is equal to (1 << 16), so a u16 is too small
to hold that value.  The result is that UART_DUMMY_DR_RX is never passed
to uart_insert_char().  This means that we're always accepting characters,
even when CREAD (in termios) is not set.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NDave Martin <Dave.Martin@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 9119fba0.

This commit prevents from sending "big" file using Bluetooth.
When sending a lot of data quickly through the Bluetooth interface, and
after a variable amount of data sent, transfer fails with error:
    kernel: [  415.247453] Bluetooth: hci0 hardware error 0x00

Found on T100TA.

After reverting this commit, send works fine for any file size.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Fixes: 9119fba0 (serial: 8250_dma: don't bother DMA with small transfers)
Cc: stable@vger.kernel.org
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The platforms that have this UART, but that don't have
separate PCI device for the DMA Engine, need to create the
HSU DMA Engine device separately.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

HSU (High Speed UART) DMA engine, like the name suggests, is
an integrated DMA engine for UART and UART alone. Therefore,
making the UART drivers responsible of selecting it and
removing the user selectable option for it. The UARTs with
this DMA engine can always select HSU_DMA when
SERIAL_8250_DMA option is enabled.
Suggested-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A recent patch to create common helper functions for modem control
lines created empty helper functions in a header file, but accidentally
did not mark them as 'static inline', which causes build errors:

drivers/tty/serial/mxs-auart.o: In function `mctrl_gpio_enable_ms':
mxs-auart.c:(.text+0x171c): multiple definition of `mctrl_gpio_enable_ms'
drivers/tty/serial/clps711x.o:clps711x.c:(.text+0x768): first defined here
drivers/tty/serial/mxs-auart.o: In function `mctrl_gpio_disable_ms':
mxs-auart.c:(.text+0x1720): multiple definition of `mctrl_gpio_disable_ms'
drivers/tty/serial/clps711x.o:clps711x.c:(.text+0x76c): first defined here

This adds the missing annotation, so the functions do not get placed
in each object file.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: ce59e48f ("serial: mctrl_gpio: implement interrupt handling")
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel MID UART quirks require already quite a bit of code
in 8250_pci.c. On new Intel platforms where it is used, the
integrated DMA engine no longer has its own PCI device, but
is instead configured from the UART's MMIO. That means we
will have to add even more code for handling just MID UARTs.

Instead of adding that to 8250_pci.c, splitting the support
of Intel MID UART into its own driver. Handling of the
integrated DMA engine becomes much simpler this way. Own
driver will also remove the need for things like specific
set_termios hooks for every board using this UART, and
simplify the handling of it in general.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for DT and command line based earlycon support for
lpuart and lpuart32 used on Freescale Vybrid and and QorIQ LS1021A
processors.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We recently got rid of some modular code in this driver and also
got rid of the unused ".remove" function at the same time.  Thierry
noted that it was however possible to force the remove through the
bind/unbind interface.

Since this is a console device used on 2005 vintage 74xx based
powerpc embedded targets, and is essentially always used in
conjunction with SERIAL_MPSC_CONSOLE=y -- there is no sane reason
anyone would ever want to unbind the builtin driver and lose the
console.  So we just explicitly block bind/unbind operations and
prevent root from shooting themselves in the foot.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a misplaced bracket in atmel_init_rs485 which sets
rs485-rx-during-tx and rs485-enabled-at-boot-time only if
rs485-rts-delay is set in of.

This is clearly a bug, so fix it by moving the bracket to the proper
place.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Elen Song <elen.song@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>