early_init() is called in-place before kernel relocation and using
whatever MMU setup exists at the point the kernel is entered.

machine_init() is called after relocation and after some initial
mapping of PAGE_OFFSET has been established (typically using BATs
on 6xx/7xx/7xxx processors or some form of bolted TLB on others).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

eeh_cache.c doesn't build cleanly with -DDEBUG when
CONFIG_PHYS_ADDR_T_64BIT is set, as a couple of pr_debug()s use "%lx" for
resource_size_t parameters.

Use "%pap" instead, as it's the correct format specifier for types deriving
from phys_addr_t.
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

A strange behaviour is observed when comparing PCI hotplug in QEMU, between
x86 and pseries. If you consider the following steps:
- start a VM
- add a PCI device via the QEMU monitor before the rtasd has started (for
  example starting the VM in paused state, or hotplug during FW or boot
  loader)
- resume the VM execution

The x86 kernel detects the PCI device, but the pseries one does not.

This happens because the rtasd kernel worker is currently started under
device_initcall, while PCI probing happens earlier under subsys_initcall.

As a consequence, if we have a pending RTAS event at boot time, a message
is printed and the event is dropped.

This patch moves all the initialization of rtasd to arch_initcall, which is
run before subsys_call: this way, logging_enabled is true when the RTAS
event pops up and it is not lost anymore.

The proc fs bits stay at device_initcall because they cannot be run before
fs_initcall.
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The domain/PHB field of PCI addresses has its value obtained from a
global variable, incremented each time a new domain (represented by
struct pci_controller) is added on the system. The domain addition
process happens during boot or due to PHB hotplug add.

As recent kernels are using predictable naming for network interfaces,
the network stack is more tied to PCI naming. This can be a problem in
hotplug scenarios, because PCI addresses will change if devices are
removed and then re-added. This situation seems unusual, but it can
happen if a user wants to replace a NIC without rebooting the machine,
for example.

This patch changes the way PCI domain values are generated: now, we use
device-tree properties to assign fixed PHB numbers to PCI addresses
when available (meaning pSeries and PowerNV cases). We also use a bitmap
to allow dynamic PHB numbering when device-tree properties are not
used. This bitmap keeps track of used PHB numbers and if a PHB is
released (by hotplug operations for example), it allows the reuse of
this PHB number, avoiding PCI address to change in case of device remove
and re-add soon after. No functional changes were introduced.
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NIan Munsie <imunsie@au1.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
[mpe: Drop unnecessary machine_is(pseries) test]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Despite attempting to fix this in commit fb36e907 ("powerpc/pci: Fix
SRIOV not building without EEH enabled"), the build is still broken when
PCI_IOV=y and EEH=n (eg. g5_defconfig with PCI_IOV=y):

  arch/powerpc/kernel/pci_dn.c: In function ‘remove_dev_pci_data’:
  arch/powerpc/kernel/pci_dn.c:230:18: error: unused variable ‘edev’

Incorporate Ben's idea of using __maybe_unused to avoid so many #ifdefs.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Power ISAv3 adds a large decrementer (LD) mode which increases the size
of the decrementer register. The size of the enlarged decrementer
register is between 32 and 64 bits with the exact size being dependent
on the implementation. When in LD mode, reads are sign extended to 64
bits and a decrementer exception is raised when the high bit is set (i.e
the value goes below zero). Writes however are truncated to the physical
register width so some care needs to be taken to ensure that the high
bit is not set when reloading the decrementer. This patch adds support
for using the LD inside the host kernel on processors that support it.

When LD mode is supported firmware will supply the ibm,dec-bits property
for CPU nodes to allow the kernel to determine the maximum decrementer
value. Enabling LD mode is a hypervisor privileged operation so the kernel
can only enable it manually when running in hypervisor mode. Guests that
support LD mode can request it using the "ibm,client-architecture-support"
firmware call (not implemented in this patch) or some other platform
specific method. If this property is not supplied then the traditional
decrementer width of 32 bit is assumed and LD mode will not be enabled.

This patch was based on initial work by Jack Miller.
Signed-off-by: NOliver O'Halloran <oohall@gmail.com>
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If ppc_rtas() is called with args.nargs == 16 and args.nret == 0,
args.rets is set to point to &args.args[16], which is beyond the end of
the args.args array. This results in a minor read overrun of the array
when we check the first return code (which, per PAPR, is a required
output of all RTAS calls) to see if there's been a hardware error.

Change the nargs/nret check to ensure nargs is <= 15, allowing room for
the status code. Users shouldn't be calling with nret == 0, but there's
no real harm if they do, so we don't stop them.
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Calling ISA 3.0 instructions copy, copy_first, paste and paste_last
generates an alignment fault when copying or pasting unaligned
data (128 byte). We catch this and send SIGBUS to the userspace
process that caused it.

We do not emulate these because paste may contain additional metadata
when pasting to a co-processor and paste_last is the synchronisation
point for preceding copy/paste sequences.

Thanks to Michael Neuling <mikey@neuling.org> for his help.
Signed-off-by: NChris Smart <chris@distroguy.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Factor out the power8 pmu init functions to share with
power9. Monitor Mode Control Register S(MMCRS) and
Monitor Mode Control Register H(MMCRH) registers are
dropped in Power9. These registers are added to new
function which are included for power8 init.
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We spent so much time bike-shedding the printk() we missed that the next
line was missing a semi-colon. And it seems none of our defconfigs turn
on CONFIG_FA_DUMP.

Fixes: 4a03749f ("powerpc/fadump: Trivial fix of spelling mistake, clean up message")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fix trivial spelling mistake "rgistration". Also use pr_err()
instead of printk() and unsplit the string to keep it all on one
line.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
[mpe: Keep rc on the same line, splitting it doesn't help]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If a PHB has no I/O space, there's no need to make it look like
something bad happened, a pr_debug() is plenty enough since this
is the case of all our modern POWER chips.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The pdn (struct pci_dn) instances are allocated from memblock or
bootmem when creating PCI controller (hoses) in setup_arch(). PCI
hotplug, which will be supported by proceeding patches, releases
PCI device nodes and their corresponding pdn on unplugging event.
The memory chunks for pdn instances allocated from memblock or
bootmem are hard to reused after being released.

This delays creating pdn by pci_devs_phb_init() from setup_arch()
to core_initcall() so that they are allocated from slab. The memory
consumed by pdn can be released to system without problem during
PCI unplugging time. It indicates that pci_dn is unavailable in
setup_arch() and the the fixup on pdn (like AGP's) can't be carried
out that time. We have to do that in pcibios_root_bridge_prepare()
on maple/pasemi/powermac platforms where/when the pdn is available.
pcibios_root_bridge_prepare is called from subsys_initcall() which
is executed after core_initcall() so the code flow does not change.

At the mean while, the EEH device is created when pdn is populated,
meaning pdn and EEH device have same life cycle. In turn, we needn't
call eeh_dev_init() to create EEH device explicitly.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On the PCI plugging event, PCI slot's subordinate devices are
scanned and their (IO and MMIO) resources are assigned. Platform
dependent resources (PE#, IO/MMIO/DMA windows) are allocated or
created on updating windows of the slot's upstream bridge.

This updates the windows of the hot plugged slot's upstream bridge
in pcibios_finish_adding_to_bus() so that the platform resources
(PE#, IO/MMIO/DMA segments) are allocated or created accordingly.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This overrides pcibios_setup_bridge() that is called to update PCI
bridge windows when PCI resource assignment is completed, to assign
PE and setup various (resource) mapping for the PE in subsequent
patches.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Export cpu_to_core_id(). This will be used by the lpfc driver.

This enables topology_core_id() from <linux/topology.h> (defined
to cpu_to_core_id() in arch/powerpc/include/asm/topology.h) to be
used by (non-builtin) modules.

That is arch-neutral, already used by eg, drivers/base/topology.c,
but it is builtin (obj-y in Makefile) thus didn't need the export.

Since the module uses topology_core_id() and this is defined to
cpu_to_core_id(), it needs the export, otherwise:

    ERROR: "cpu_to_core_id" [drivers/scsi/lpfc/lpfc.ko] undefined!

Tested on next-20160601.
Signed-off-by: NMauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This enables new registers, LMRR and LMSER, that can trigger an EBB in
userspace code when a monitored load (via the new ldmx instruction)
loads memory from a monitored space. This facility is controlled by a
new FSCR bit, LM.

This patch disables the FSCR LM control bit on task init and enables
that bit when a load monitor facility unavailable exception is taken
for using it. On context switch, this bit is then used to determine
whether the two relevant registers are saved and restored. This is
done lazily for performance reasons.
Signed-off-by: NJack Miller <jack@codezen.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This fixes a few issues with FSCR init and switching.

In commit 152d523e ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") we moved the setting of the FSCR
register from inside an CPU_FTR_ARCH_207S section to inside just a
CPU_FTR_ARCH_DSCR section. Hence we are setting FSCR on POWER6/7 where
the FSCR doesn't exist. This is harmless but we shouldn't do it.

Also, we can simplify the FSCR context switch. We don't need to go
through the calculation involving dscr_inherit. We can just restore
what we saved last time.

We also set an initial value in INIT_THREAD, so that pid 1 which is
cloned from that gets a sane value.

Based on patch by Jack Miller.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Current comment in the early_setup_secondary() for paca->soft_enabled
update is misleading. Comment should say to Mark interrupts "disabled"
instead of "enabled". Fix the typo.
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fixes the following testsuite failure:

  $ sudo ./perf test -v kallsyms
   1: vmlinux symtab matches kallsyms                          :
  --- start ---
  test child forked, pid 12489
  Using /proc/kcore for kernel object code
  Looking at the vmlinux_path (8 entries long)
  Using /boot/vmlinux for symbols
  0xc00000000003d300: diff name v: .kretprobe_trampoline_holder k: kretprobe_trampoline
  Maps only in vmlinux:
   c00000000086ca38-c000000000879b6c 87ca38 [kernel].text.unlikely
   c000000000879b6c-c000000000bf0000 889b6c [kernel].meminit.text
   c000000000bf0000-c000000000c53264 c00000 [kernel].init.text
   c000000000c53264-d000000004250000 c63264 [kernel].exit.text
   d000000004250000-d000000004450000 0 [libcrc32c]
   d000000004450000-d000000004620000 0 [xfs]
   d000000004620000-d000000004680000 0 [autofs4]
   d000000004680000-d0000000046e0000 0 [x_tables]
   d0000000046e0000-d000000004780000 0 [ip_tables]
   d000000004780000-d0000000047e0000 0 [rng_core]
   d0000000047e0000-ffffffffffffffff 0 [pseries_rng]
  Maps in vmlinux with a different name in kallsyms:
  Maps only in kallsyms:
   d000000000000000-f000000000000000 1000000000010000 [kernel.kallsyms]
   f000000000000000-ffffffffffffffff 3000000000010000 [kernel.kallsyms]
  test child finished with -1
  ---- end ----
  vmlinux symtab matches kallsyms: FAILED!

The problem is that the kretprobe_trampoline symbol looks like this:

  $ eu-readelf -s /boot/vmlinux G kretprobe_trampoline
   2431: c000000001302368     24 NOTYPE  LOCAL  DEFAULT       37 kretprobe_trampoline_holder
   2432: c00000000003d300      8 FUNC    LOCAL  DEFAULT        1 .kretprobe_trampoline_holder
  97543: c00000000003d300      0 NOTYPE  GLOBAL DEFAULT        1 kretprobe_trampoline

Its type is NOTYPE, and its size is 0, and this is a problem because
symbol-elf.c:dso__load_sym skips function symbols that are not STT_FUNC
or STT_GNU_IFUNC (this is determined by elf_sym__is_function). Even
if the type is changed to STT_FUNC, when dso__load_sym calls
symbols__fixup_duplicate, the kretprobe_trampoline symbol is dropped in
favour of .kretprobe_trampoline_holder because the latter has non-zero
size (as determined by choose_best_symbol).

With this patch, all vmlinux symbols match /proc/kallsyms and the
testcase passes.

Commit c1c355ce ("x86/kprobes: Get rid of
kretprobe_trampoline_holder()") gets rid of kretprobe_trampoline_holder
altogether on x86. This commit does the same on powerpc. This change
introduces no regressions on the perf and ftracetest testsuite results.
Reviewed-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NThiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On Book3E CPUs (and possibly other configs), it is possible to have SRIOV
(CONFIG_PCI_IOV) set without CONFIG_EEH.  The SRIOV code does not check
for this, and if EEH is disabled, pci_dn.c fails to build.

Fix this by gating the EEH-specific code in the SRIOV implementation
behind CONFIG_EEH.

Fixes: 39218cd0 ("powerpc/eeh: EEH device for VF")
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse complains that it doesn't know what REG_BYTE is:

  arch/powerpc/kernel/align.c:313:29: error: undefined identifier 'REG_BYTE'

REG_BYTE is defined differently based on whether we're compiling for
LE, BE32 or BE64. Sparse apparently doesn't provide __BIG_ENDIAN__ or
__LITTLE_ENDIAN__, which means we get no definition.

Rather than check for __BIG_ENDIAN__ and then separately for
__LITTLE_ENDIAN__, just switch the #ifdef to check for __BIG_ENDIAN__
and then #else we define the little endian version. Technically that's
dicey because PDP_ENDIAN is also a possibility, but we already do it in
a lot of places so one more hardly matters.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sometimes headers that provide prototypes for functions are
accidentally omitted from the files that define the functions.

Fix a couple of times that occurs.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse picked up a number of functions that are implemented in C and
then only referred to in asm code.

This introduces asm-prototypes.h, which provides a place for
prototypes of these functions.

This silences some sparse warnings.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
[mpe: Add include guards, clean up copyright & GPL text]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is just a smattering of things picked up by sparse that should
be made static.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The array crash_shutdown_handles is an array of size CRASH_HANDLER_MAX+1
containing up to CRASH_HANDLER_MAX shutdown_handlers. It is assumed to
be NULL terminated, which it is under normal circumstances. Array
accesses in the functions crash_shutdown_unregister() and
default_machine_crash_shutdown() rely on this NULL termination property
when traversing this list and don't protect again out of bounds accesses.
If the NULL terminator were somehow overwritten these functions could
potentially access out of the bounds of the array.

Shrink the array to size CRASH_HANDLER_MAX and implement explicit array
bounds checking when accessing the elements of the
crash_shutdown_handles[] array in crash_shutdown_unregister() and
default_machine_crash_shutdown().
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

THREAD_DSCR:
  Added in efcac658 "powerpc: Per process DSCR + some fixes (try#4)"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_DSCR_INHERIT:
  Added in 71433285 "powerpc: Restore correct DSCR in context switch"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_TAR:
  Added in 2468dcf6 "powerpc: Add support for context switching the TAR register"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_BESCR, THREAD_EBBHR and THREAD_EBBRR:
  Added in 9353374b "powerpc: Context switch the new EBB SPRs"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_SIAR, THREAD_SDAR, THREAD_SIER, THREAD_MMCR0, and THREAD_MMCR2:
  Added in 59affcd3 "powerpc: Context switch more PMU related SPRs"
  Last usage removed in b11ae951 "powerpc: Partial revert of "Context switch more PMU related SPRs""

PACA_LOCK_TOKEN:
  Added in 9e368f29 "KVM: PPC: book3s_hv: Add support for PPC970-family processors"
  Last usage removed in c17b98cf "KVM: PPC: Book3S HV: Remove code for PPC970 processors"

HCALL_STAT_SIZE, HCALL_STAT_CALLS, HCALL_STAT_TB and HCALL_STAT_PURR:
  Added in 57852a85 "[POWERPC] powerpc: Instrument Hypervisor Calls"
  Last usage removed in c8cd093a "powerpc: tracing: Add hypervisor call tracepoints"

VCPU_EPLC:
  Added in d30f6e48 "KVM: PPC: booke: category E.HV (GS-mode) support"
  Never used.

CPU_DOWN_FLUSH:
  Added in e7affb1d "powerpc/cache: add cache flush operation for various e500"
  Never used.

CFG_STAMP_XSEC:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Last usage removed in 0e469db8 "powerpc: Rework VDSO gettimeofday to prevent time going backwards"

KVM_LPCR:
  Added in aa04b4cc "KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests"
  Last usage removed in a0144e2a "KVM: PPC: Book3S HV: Store LPCR value for each virtual core"

GPR15, GPR16, GPR17, GPR18, GPR19, GPR20, GPR21, GPR22, GPR23, GPR24,
GPR25, GPR26, GPR27, GPR28, GPR29, GPR30 and GPR31:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Never used.

VCPU_SHADOW_FSCR:
  Added in 616dff86 "KVM: PPC: Book3S PR: Handle Facility interrupt and FSCR"
  Never used.

VCPU_SHADOW_SRR1:
  Added in a2d56020 "KVM: PPC: Book3S PR: Keep volatile reg values in vcpu rather than shadow_vcpu"
  Never used.

KVM_SPLIT_SIZE:
  Added in b4deba5c "KVM: PPC: Book3S HV: Implement dynamicmicro-threading on POWER8"
  Never used.

VCPU_VCPUID:
  Added in de56a948 "KVM: PPC: Add support for Book3S processors in hypervisor mode"
  Last usage removed 1b400ba0 "KVM: PPC: Book3S HV: Improve handling of local vs. global TLB invalidations"

_MQ:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Never used.

AUDITCONTEXT:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Last usage removed in 401d1f02 "[PATCH] syscall entry/exit revamp"

CLONE_VM:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Currently unused.

CLONE_UNTRACED:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Currently unused.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
[mpe: Munge change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We're approaching 20 locations where we need to check for ELF ABI v2.
That's fine, except the logic is a bit awkward, because we have to check
that _CALL_ELF is defined and then what its value is.

So check it once in asm/types.h and define PPC64_ELF_ABI_v2 when ELF ABI
v2 is detected.

We also have a few places where what we're really trying to check is
that we are using the 64-bit v1 ABI, ie. function descriptors. So also
add a #define for that, which simplifies several checks.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

sub_reloc_offset() has not been used since commit
917f0af9 ("powerpc: Remove arch/ppc and include/asm-ppc") which
removed include/asm-ppc/prom.h.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In setup_sigcontext(), we set current->thread.vrsave then use it
straight after. Since current is hidden from the compiler via inline
assembly, it cannot optimise this and we end up with a load hit store.

Fix this by using a temporary.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In both __giveup_fpu() and __giveup_altivec() we make two modifications
to tsk->thread.regs->msr. gcc decides to do a read/modify/write of
each change, so we end up with a load hit store:

        ld      r9,264(r10)
        rldicl  r9,r9,50,1
        rotldi  r9,r9,14
        std     r9,264(r10)
...
        ld      r9,264(r10)
        rldicl  r9,r9,40,1
        rotldi  r9,r9,24
        std     r9,264(r10)

Fix this by using a temporary.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The recent commit 7cc85103 ("powerpc/pseries: Add POWER8NVL support
to ibm,client-architecture-support call") added a new PVR mask & value
to the start of the ibm_architecture_vec[] array.

However it missed the fact that further down in the array, we hard code
the offset of one of the fields, and then at boot use that value to
patch the value in the array. This means every update to the array must
also update the #define, ugh.

This means that on pseries machines we will misreport to firmware the
number of cores we support, by a factor of threads_per_core.

Fix it for now by updating the #define.

Fixes: 7cc85103 ("powerpc/pseries: Add POWER8NVL support to ibm,client-architecture-support call")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

gcc-6 correctly warns about a out of bounds access

arch/powerpc/kernel/ptrace.c:407:24: warning: index 32 denotes an offset greater than size of 'u64[32][1] {aka long long unsigned int[32][1]}' [-Warray-bounds]
        offsetof(struct thread_fp_state, fpr[32][0]));
                        ^

check the end of array instead of beginning of next element to fix this
Signed-off-by: NKhem Raj <raj.khem@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If we do not provide the PVR for POWER8NVL, a guest on this system
currently ends up in PowerISA 2.06 compatibility mode on KVM, since QEMU
does not provide a generic PowerISA 2.07 mode yet. So some new
instructions from POWER8 (like "mtvsrd") get disabled for the guest,
resulting in crashes when using code compiled explicitly for
POWER8 (e.g. with the "-mcpu=power8" option of GCC).

Fixes: ddee09c0 ("powerpc: Add PVR for POWER8NVL processor")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

most architectures are relying on mmap_sem for write in their
arch_setup_additional_pages.  If the waiting task gets killed by the oom
killer it would block oom_reaper from asynchronous address space reclaim
and reduce the chances of timely OOM resolving.  Wait for the lock in
the killable mode and return with EINTR if the task got killed while
waiting.
Signed-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>	[x86 vdso]
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.

This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.

[akpm@linux-foundation.org: fix mips]
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 89a51df5.

The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5 ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.

However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.

This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc0 ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.

Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>