This enables new registers, LMRR and LMSER, that can trigger an EBB in
userspace code when a monitored load (via the new ldmx instruction)
loads memory from a monitored space. This facility is controlled by a
new FSCR bit, LM.

This patch disables the FSCR LM control bit on task init and enables
that bit when a load monitor facility unavailable exception is taken
for using it. On context switch, this bit is then used to determine
whether the two relevant registers are saved and restored. This is
done lazily for performance reasons.
Signed-off-by: NJack Miller <jack@codezen.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This fixes a few issues with FSCR init and switching.

In commit 152d523e ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") we moved the setting of the FSCR
register from inside an CPU_FTR_ARCH_207S section to inside just a
CPU_FTR_ARCH_DSCR section. Hence we are setting FSCR on POWER6/7 where
the FSCR doesn't exist. This is harmless but we shouldn't do it.

Also, we can simplify the FSCR context switch. We don't need to go
through the calculation involving dscr_inherit. We can just restore
what we saved last time.

We also set an initial value in INIT_THREAD, so that pid 1 which is
cloned from that gets a sane value.

Based on patch by Jack Miller.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Current comment in the early_setup_secondary() for paca->soft_enabled
update is misleading. Comment should say to Mark interrupts "disabled"
instead of "enabled". Fix the typo.
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fixes the following testsuite failure:

  $ sudo ./perf test -v kallsyms
   1: vmlinux symtab matches kallsyms                          :
  --- start ---
  test child forked, pid 12489
  Using /proc/kcore for kernel object code
  Looking at the vmlinux_path (8 entries long)
  Using /boot/vmlinux for symbols
  0xc00000000003d300: diff name v: .kretprobe_trampoline_holder k: kretprobe_trampoline
  Maps only in vmlinux:
   c00000000086ca38-c000000000879b6c 87ca38 [kernel].text.unlikely
   c000000000879b6c-c000000000bf0000 889b6c [kernel].meminit.text
   c000000000bf0000-c000000000c53264 c00000 [kernel].init.text
   c000000000c53264-d000000004250000 c63264 [kernel].exit.text
   d000000004250000-d000000004450000 0 [libcrc32c]
   d000000004450000-d000000004620000 0 [xfs]
   d000000004620000-d000000004680000 0 [autofs4]
   d000000004680000-d0000000046e0000 0 [x_tables]
   d0000000046e0000-d000000004780000 0 [ip_tables]
   d000000004780000-d0000000047e0000 0 [rng_core]
   d0000000047e0000-ffffffffffffffff 0 [pseries_rng]
  Maps in vmlinux with a different name in kallsyms:
  Maps only in kallsyms:
   d000000000000000-f000000000000000 1000000000010000 [kernel.kallsyms]
   f000000000000000-ffffffffffffffff 3000000000010000 [kernel.kallsyms]
  test child finished with -1
  ---- end ----
  vmlinux symtab matches kallsyms: FAILED!

The problem is that the kretprobe_trampoline symbol looks like this:

  $ eu-readelf -s /boot/vmlinux G kretprobe_trampoline
   2431: c000000001302368     24 NOTYPE  LOCAL  DEFAULT       37 kretprobe_trampoline_holder
   2432: c00000000003d300      8 FUNC    LOCAL  DEFAULT        1 .kretprobe_trampoline_holder
  97543: c00000000003d300      0 NOTYPE  GLOBAL DEFAULT        1 kretprobe_trampoline

Its type is NOTYPE, and its size is 0, and this is a problem because
symbol-elf.c:dso__load_sym skips function symbols that are not STT_FUNC
or STT_GNU_IFUNC (this is determined by elf_sym__is_function). Even
if the type is changed to STT_FUNC, when dso__load_sym calls
symbols__fixup_duplicate, the kretprobe_trampoline symbol is dropped in
favour of .kretprobe_trampoline_holder because the latter has non-zero
size (as determined by choose_best_symbol).

With this patch, all vmlinux symbols match /proc/kallsyms and the
testcase passes.

Commit c1c355ce ("x86/kprobes: Get rid of
kretprobe_trampoline_holder()") gets rid of kretprobe_trampoline_holder
altogether on x86. This commit does the same on powerpc. This change
introduces no regressions on the perf and ftracetest testsuite results.
Reviewed-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NThiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On Book3E CPUs (and possibly other configs), it is possible to have SRIOV
(CONFIG_PCI_IOV) set without CONFIG_EEH.  The SRIOV code does not check
for this, and if EEH is disabled, pci_dn.c fails to build.

Fix this by gating the EEH-specific code in the SRIOV implementation
behind CONFIG_EEH.

Fixes: 39218cd0 ("powerpc/eeh: EEH device for VF")
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds support for using CAPP DMA mode, which is required for XSL
based cards such as the Mellanox CX4 to function.

This is currently an RFC as it depends on the corresponding support to
be merged into skiboot first, which was submitted here:
http://patchwork.ozlabs.org/patch/625582/

In the event that the skiboot on the system does not have the above
support, it will indicate as such in the kernel log and abort the init
process.
Signed-off-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse complains that it doesn't know what REG_BYTE is:

  arch/powerpc/kernel/align.c:313:29: error: undefined identifier 'REG_BYTE'

REG_BYTE is defined differently based on whether we're compiling for
LE, BE32 or BE64. Sparse apparently doesn't provide __BIG_ENDIAN__ or
__LITTLE_ENDIAN__, which means we get no definition.

Rather than check for __BIG_ENDIAN__ and then separately for
__LITTLE_ENDIAN__, just switch the #ifdef to check for __BIG_ENDIAN__
and then #else we define the little endian version. Technically that's
dicey because PDP_ENDIAN is also a possibility, but we already do it in
a lot of places so one more hardly matters.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sometimes headers that provide prototypes for functions are
accidentally omitted from the files that define the functions.

Fix a couple of times that occurs.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse picked up a number of functions that are implemented in C and
then only referred to in asm code.

This introduces asm-prototypes.h, which provides a place for
prototypes of these functions.

This silences some sparse warnings.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
[mpe: Add include guards, clean up copyright & GPL text]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is just a smattering of things picked up by sparse that should
be made static.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The array crash_shutdown_handles is an array of size CRASH_HANDLER_MAX+1
containing up to CRASH_HANDLER_MAX shutdown_handlers. It is assumed to
be NULL terminated, which it is under normal circumstances. Array
accesses in the functions crash_shutdown_unregister() and
default_machine_crash_shutdown() rely on this NULL termination property
when traversing this list and don't protect again out of bounds accesses.
If the NULL terminator were somehow overwritten these functions could
potentially access out of the bounds of the array.

Shrink the array to size CRASH_HANDLER_MAX and implement explicit array
bounds checking when accessing the elements of the
crash_shutdown_handles[] array in crash_shutdown_unregister() and
default_machine_crash_shutdown().
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The mm zone mechanism was traditionally used by arch specific code to
partition memory into allocation zones. However there are several zones
that are managed by the mm subsystem rather than the architecture. Most
architectures set the max PFN of these special zones to zero, however on
powerpc we set them to ~0ul. This, in conjunction with a bug in
free_area_init_nodes() results in all of system memory being placed in
ZONE_DEVICE when enabled. Device memory cannot be used for regular kernel
memory allocations so this will cause a kernel panic at boot. Given the
planned addition of more mm managed zones (ZONE_CMA) we should aim to be
consistent with every other architecture and set the max PFN for these
zones to zero.
Signed-off-by: NOliver O'Halloran <oohall@gmail.com>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

THREAD_DSCR:
  Added in efcac658 "powerpc: Per process DSCR + some fixes (try#4)"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_DSCR_INHERIT:
  Added in 71433285 "powerpc: Restore correct DSCR in context switch"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_TAR:
  Added in 2468dcf6 "powerpc: Add support for context switching the TAR register"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_BESCR, THREAD_EBBHR and THREAD_EBBRR:
  Added in 9353374b "powerpc: Context switch the new EBB SPRs"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_SIAR, THREAD_SDAR, THREAD_SIER, THREAD_MMCR0, and THREAD_MMCR2:
  Added in 59affcd3 "powerpc: Context switch more PMU related SPRs"
  Last usage removed in b11ae951 "powerpc: Partial revert of "Context switch more PMU related SPRs""

PACA_LOCK_TOKEN:
  Added in 9e368f29 "KVM: PPC: book3s_hv: Add support for PPC970-family processors"
  Last usage removed in c17b98cf "KVM: PPC: Book3S HV: Remove code for PPC970 processors"

HCALL_STAT_SIZE, HCALL_STAT_CALLS, HCALL_STAT_TB and HCALL_STAT_PURR:
  Added in 57852a85 "[POWERPC] powerpc: Instrument Hypervisor Calls"
  Last usage removed in c8cd093a "powerpc: tracing: Add hypervisor call tracepoints"

VCPU_EPLC:
  Added in d30f6e48 "KVM: PPC: booke: category E.HV (GS-mode) support"
  Never used.

CPU_DOWN_FLUSH:
  Added in e7affb1d "powerpc/cache: add cache flush operation for various e500"
  Never used.

CFG_STAMP_XSEC:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Last usage removed in 0e469db8 "powerpc: Rework VDSO gettimeofday to prevent time going backwards"

KVM_LPCR:
  Added in aa04b4cc "KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests"
  Last usage removed in a0144e2a "KVM: PPC: Book3S HV: Store LPCR value for each virtual core"

GPR15, GPR16, GPR17, GPR18, GPR19, GPR20, GPR21, GPR22, GPR23, GPR24,
GPR25, GPR26, GPR27, GPR28, GPR29, GPR30 and GPR31:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Never used.

VCPU_SHADOW_FSCR:
  Added in 616dff86 "KVM: PPC: Book3S PR: Handle Facility interrupt and FSCR"
  Never used.

VCPU_SHADOW_SRR1:
  Added in a2d56020 "KVM: PPC: Book3S PR: Keep volatile reg values in vcpu rather than shadow_vcpu"
  Never used.

KVM_SPLIT_SIZE:
  Added in b4deba5c "KVM: PPC: Book3S HV: Implement dynamicmicro-threading on POWER8"
  Never used.

VCPU_VCPUID:
  Added in de56a948 "KVM: PPC: Add support for Book3S processors in hypervisor mode"
  Last usage removed 1b400ba0 "KVM: PPC: Book3S HV: Improve handling of local vs. global TLB invalidations"

_MQ:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Never used.

AUDITCONTEXT:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Last usage removed in 401d1f02 "[PATCH] syscall entry/exit revamp"

CLONE_VM:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Currently unused.

CLONE_UNTRACED:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Currently unused.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
[mpe: Munge change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

memory_hotplug_max() uses hot_add_drconf_memory_max() to get maxmimum
addressable memory by referring to ibm,dyanamic-memory property. There
are three problems with the current approach:

1 hot_add_drconf_memory_max() assumes that ibm,dynamic-memory includes
  all the LMBs of the guest, but that is not true for PowerKVM which
  populates only DR LMBs (LMBs that can be hotplugged/removed) in that
  property.
2 hot_add_drconf_memory_max() multiplies lmb-size with lmb-count to arrive
  at the max possible address. Since ibm,dynamic-memory doesn't include
  RMA LMBs, the address thus obtained will be less than the actual max
  address. For example, if max possible memory size is 32G, with lmb-size
  of 256MB there can be 127 LMBs in ibm,dynamic-memory (1 LMB for RMA
  which won't be present here).  hot_add_drconf_memory_max() would then
  return the max addressable memory as 127 * 256MB = 31.75GB, the max
  address should have been 32G which is what ibm,lrdr-capacity shows.
3 In PowerKVM, there can be a gap between the end of boot time RAM and
  beginning of hotplug RAM area. So just multiplying lmb-count with
  lmb-size will not provide the correct max possible address for PowerKVM.

This patch fixes 1 by using ibm,lrdr-capacity property to return the max
addressable memory whenever the property is present. Then it fixes 2 & 3
by fetching the address of the last LMB in ibm,dynamic-memory property.

Fixes: cd34206e ("powerpc: Add memory_hotplug_max()")
Signed-off-by: NBharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NBharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There is an ordering issue with spin_unlock_wait() on powerpc, because
the spin_lock primitive is an ACQUIRE and an ACQUIRE is only ordering
the load part of the operation with memory operations following it.
Therefore the following event sequence can happen:

CPU 1			CPU 2			CPU 3

==================	====================	==============
						spin_unlock(&lock);
			spin_lock(&lock):
			  r1 = *lock; // r1 == 0;
o = object;		o = READ_ONCE(object); // reordered here
object = NULL;
smp_mb();
spin_unlock_wait(&lock);
			  *lock = 1;
smp_mb();
o->dead = true;         < o = READ_ONCE(object); > // reordered upwards
			if (o) // true
				BUG_ON(o->dead); // true!!

To fix this, we add a "nop" ll/sc loop in arch_spin_unlock_wait() on
ppc, the "nop" ll/sc loop reads the lock
value and writes it back atomically, in this way it will synchronize the
view of the lock on CPU1 with that on CPU2. Therefore in the scenario
above, either CPU2 will fail to get the lock at first or CPU1 will see
the lock acquired by CPU2, both cases will eliminate this bug. This is a
similar idea as what Will Deacon did for ARM64 in:

  d86b8da0 ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")

Furthermore, if the "nop" ll/sc figures out the lock is locked, we
actually don't need to do the "nop" ll/sc trick again, we can just do a
normal load+check loop for the lock to be released, because in that
case, spin_unlock_wait() is called when someone is holding the lock, and
the store part of the "nop" ll/sc happens before the lock release of the
current lock holder:

	"nop" ll/sc -> spin_unlock()

and the lock release happens before the next lock acquisition:

	spin_unlock() -> spin_lock() <next holder>

which means the "nop" ll/sc happens before the next lock acquisition:

	"nop" ll/sc -> spin_unlock() -> spin_lock() <next holder>

With a smp_mb() preceding spin_unlock_wait(), the store of object is
guaranteed to be observed by the next lock holder:

	STORE -> smp_mb() -> "nop" ll/sc
	-> spin_unlock() -> spin_lock() <next holder>

This patch therefore fixes the issue and also cleans the
arch_spin_unlock_wait() a little bit by removing superfluous memory
barriers in loops and consolidating the implementations for PPC32 and
PPC64 into one.
Suggested-by: N"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: NBoqun Feng <boqun.feng@gmail.com>
Reviewed-by: N"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
[mpe: Inline the "nop" ll/sc loop and set EH=0, munge change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since the pstore code has moved away from nvram.c, remove unused
pstore headers pstore.h and kmsg_dump.h.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We're approaching 20 locations where we need to check for ELF ABI v2.
That's fine, except the logic is a bit awkward, because we have to check
that _CALL_ELF is defined and then what its value is.

So check it once in asm/types.h and define PPC64_ELF_ABI_v2 when ELF ABI
v2 is detected.

We also have a few places where what we're really trying to check is
that we are using the 64-bit v1 ABI, ie. function descriptors. So also
add a #define for that, which simplifies several checks.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code. XICS is now the only supported interrupt controller for
pSeries so do some cleanups too.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code. XICS is now the only supported interrupt controller for
pSeries so do some cleanups too.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code. XICS is now the only supported interrupt controller for
pSeries so do some cleanups too.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so drop support
for MPIC. XICS is now the only supported interrupt controller for
pSeries so make the XICS functions generic.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

sub_reloc_offset() has not been used since commit
917f0af9 ("powerpc: Remove arch/ppc and include/asm-ppc") which
removed include/asm-ppc/prom.h.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Align the hot loops in our assembly implementation of strncpy(),
strncmp() and memchr().
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

A number of our assembly implementations of string functions do not
align their hot loops. I was going to align them manually, but I
realised that they are are almost instruction for instruction
identical to what gcc produces, with the advantage that gcc does
align them.

In light of that, let's just remove the assembly versions.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In setup_sigcontext(), we set current->thread.vrsave then use it
straight after. Since current is hidden from the compiler via inline
assembly, it cannot optimise this and we end up with a load hit store.

Fix this by using a temporary.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In both __giveup_fpu() and __giveup_altivec() we make two modifications
to tsk->thread.regs->msr. gcc decides to do a read/modify/write of
each change, so we end up with a load hit store:

        ld      r9,264(r10)
        rldicl  r9,r9,50,1
        rotldi  r9,r9,14
        std     r9,264(r10)
...
        ld      r9,264(r10)
        rldicl  r9,r9,40,1
        rotldi  r9,r9,24
        std     r9,264(r10)

Fix this by using a temporary.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On a 4-socket Brickland system, hot-removing one ioapic is fine.
Hot-removing the 2nd one causes panic in mp_unregister_ioapic()
while calling release_resource().

It is because the iomem_res pointer has already been released
when removing the first ioapic.

To explain the use of &res[num] here: res is assigned to ioapic_resources,
and later in ioapic_insert_resources() we do:

	struct resource *r = ioapic_resources;

        for_each_ioapic(i) {
                insert_resource(&iomem_resource, r);
                r++;
        }

Here 'r' is treated as an arry of 'struct resource', and the r++ ensures
that each element of the array is inserted separately. Thus we should call
release_resouce() on each element at &res[num].

Fix it by assigning the correct pointers to ioapics[i].iomem_res in
ioapic_setup_resources().
Signed-off-by: NRui Wang <rui.y.wang@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: tony.luck@intel.com
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1465369193-4816-3-git-send-email-rui.y.wang@intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Forcing in_interrupt() to return true if we're not in a bona fide
interrupt confuses the softirq code.  This fixes warnings like:

  NOHZ: local_softirq_pending 282

... which can happen when running things like selftests/x86.

This will change perf's static percpu buffer usage in IST context.
I think this is okay, and it's changing the behavior to match
historical (pre-4.0) behavior.
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 95927475 ("x86, traps: Track entry into and exit from IST context")
Link: http://lkml.kernel.org/r/cdc215f94d118d691d73df35275022331156fb45.1464130360.git.luto@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

Commit 74701d59 "powerpc/mm: Rename function to indicate we are
allocating fragments" renamed page_table_free() to pte_fragment_free().
One occurrence was mistyped as pte_fragment_fre().

This only breaks the nohash 64K page build, which is not the default or
enabled in any defconfig.

Fixes: 74701d59 ("powerpc/mm: Rename function to indicate we are allocating fragments")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We need to reenable the topology extensions CPUID leafs on newer models
too, if BIOS has disabled them, as we rely on them to get proper compute
unit topology.

Make the printk a once thing, while at it.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rui Huang <ray.huang@amd.com>
Cc: Sherry Hurwitz <sherry.hurwitz@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-hwmon@vger.kernel.org
Link: http://lkml.kernel.org/r/1464775468-23355-1-git-send-email-bp@alien8.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Problem:

We have a boatload of open-coded family-6 model numbers.  Half of
them have these model numbers in hex and the other half in
decimal.  This makes grepping for them tons of fun, if you were
to try.

Solution:

Consolidate all the magic numbers.  Put all the definitions in
one header.

The names here are closely derived from the comments describing
the models from arch/x86/events/intel/core.c.  We could easily
make them shorter by doing things like s/SANDYBRIDGE/SNB/, but
they seemed fine even with the longer versions to me.

Do not take any of these names too literally, like "DESKTOP"
or "MOBILE".  These are all colloquial names and not precise
descriptions of everywhere a given model will show up.
Signed-off-by: NDave Hansen <dave.hansen@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Cc: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: jacob.jun.pan@intel.com
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Link: http://lkml.kernel.org/r/20160603001927.F2A7D828@viggo.jf.intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Commit 66dbd6e6 ("arm64: Implement ptep_set_access_flags() for
hardware AF/DBM") ensured that pte flags are updated atomically in the
face of potential concurrent, hardware-assisted updates. However, Alex
reports that:

 | This patch breaks swapping for me.
 | In the broken case, you'll see either systemd cpu time spike (because
 | it's stuck in a page fault loop) or the system hang (because the
 | application owning the screen is stuck in a page fault loop).

It turns out that this is because the 'dirty' argument to
ptep_set_access_flags is always 0 for read faults, and so we can't use
it to set PTE_RDONLY. The failing sequence is:

  1. We put down a PTE_WRITE | PTE_DIRTY | PTE_AF pte
  2. Memory pressure -> pte_mkold(pte) -> clear PTE_AF
  3. A read faults due to the missing access flag
  4. ptep_set_access_flags is called with dirty = 0, due to the read fault
  5. pte is then made PTE_WRITE | PTE_DIRTY | PTE_AF | PTE_RDONLY (!)
  6. A write faults, but pte_write is true so we get stuck

The solution is to check the new page table entry (as would be done by
the generic, non-atomic definition of ptep_set_access_flags that just
calls set_pte_at) to establish the dirty state.

Cc: <stable@vger.kernel.org> # 4.3+
Fixes: 66dbd6e6 ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM")
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Reported-by: NAlexander Graf <agraf@suse.de>
Tested-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

PowerISA 3.0 encodes the segment size in the second half of hash page
table entry. Update hpte_decode() accordingly.

Fixes: 50de596d ("powerpc/mm/hash: Add support for Power9 Hash")
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In some of the radix TLB flush routines, we use a local to store the
mm->context.id, AKA the PID.

Currently we use an int, but the PID is unsigned long, so large values
of PID will be truncated. In particular MMU_NO_CONTEXT is -1, which
means all our comparisons against that value can never be true.

This means we'll issue TLB flushes when we shouldn't on radix enabled
machines.

Fix it by using an unsigned long for the local. Discovered by Coverity.

Fixes: 1a472c9d ("powerpc/mm/radix: Add tlbflush routines")
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
[mpe: Write change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The offset in the core file used to be tracked with ->written field of
the coredump_params structure. The field was retired in favour of
file->f_pos.

However, ->f_pos is not maintained for pipes which leads to breakage.

Restore explicit tracking of the offset in coredump_params. Introduce
->pos field for this purpose since ->written was already reused.

Fixes: a0083939 ("get rid of coredump_params->written").
Reported-by: NZbigniew Jędrzejewski-Szmek <zbyszek@in.waw.pl>
Signed-off-by: NMateusz Guzik <mguzik@redhat.com>
Reviewed-by: NOmar Sandoval <osandov@fb.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The recent commit 7cc85103 ("powerpc/pseries: Add POWER8NVL support
to ibm,client-architecture-support call") added a new PVR mask & value
to the start of the ibm_architecture_vec[] array.

However it missed the fact that further down in the array, we hard code
the offset of one of the fields, and then at boot use that value to
patch the value in the array. This means every update to the array must
also update the #define, ugh.

This means that on pseries machines we will misreport to firmware the
number of cores we support, by a factor of threads_per_core.

Fix it for now by updating the #define.

Fixes: 7cc85103 ("powerpc/pseries: Add POWER8NVL support to ibm,client-architecture-support call")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>