This picks up the staging changes made in 3.5-rc4 so that everyone can sync up
properly.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Coult -> Could
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull KVM fixes from Avi Kivity:
 "Fixing a scheduling-while-atomic bug in the ppc code, and a bug which
  allowed pci bridges to be assigned to guests."

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Book3S HV: Drop locks around call to kvmppc_pin_guest_page
  KVM: Fix PCI header check on device assignment

Pull InfiniBand/RDMA fixes from Roland Dreier:
 - Fixes to new ocrdma driver
 - Typo in test in CMA

* tag 'rdma-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cma: QP type check on received REQs should be AND not OR
  RDMA/ocrdma: Fix off by one in ocrdma_query_gid()
  RDMA/ocrdma: Fixed RQ error CQE polling
  RDMA/ocrdma: Correct queue SGE calculation
  RDMA/ocrdma: Correct reported max queue sizes
  RDMA/ocrdma: Fixed GID table for vlan and events

Pull ARM SoC fixes from Olof Johansson:
 "Nothing very controversial in here.  Most of the fixes are for OMAP
  this time around, with some orion/kirkwood and a tegra patch mixed in."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: Orion: Fix Virtual/Physical mixup with watchdog
  ARM: Kirkwood: clk_register_gate_fn: add fn assignment
  ARM: Orion5x - Restore parts of io.h, with rework
  ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
  ARM: OMAP2+: mux: fix sparse warning
  ARM: OMAP2+: CM: increase the module disable timeout
  ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
  ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
  ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
  ARM: OMAP: Fix Beagleboard DVI reset gpio
  arm/dts: OMAP2: Fix interrupt controller binding
  ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
  ARM: OMAP2+: Fix MUSB ifdefs for platform init code
  ARM: tegra: make tegra_cpu_reset_handler_enable() __init
  ARM: OMAP: PM: Lock clocks list while generating summary
  ARM: iconnect: Remove include of removed linux/spi/orion_spi.h

Pull drm fixes from Dave Airlie:
 "Nothing major in here, one radeon SI fix for tiling, and one uninit
  var fix, two minor header file fixes."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: drop comment about this header being autogenerated.
  drm/edid: don't return stack garbage from supports_rb
  vga_switcheroo: Add include guard
  drm/radeon: SI tiling fixes for display

The orion watchdog is expecting to be passed the physcial address of
the hardware, and will ioremap() it to give a virtual address it will
use as the base address for the hardware. However, when creating the
platform resource record, a virtual address was being used.

Add the necassary #define's so we can pass the physical address as
expected.

Tested on Kirkwood and Orion5x.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NOlof Johansson <olof@lixom.net>

In commit:
    98d9986c ARM: Kirkwood: Replace clock gating
the kirkwood clock gating has been reworked. A custom variant of
clock gating, that calls a custom function before gating the clock
off, has been introduced. However in clk_register_gate_fn() this
custom function "fn" is never assigned.

This patch adds the missing fn assignment.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@blackshift.org>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit 4d5fc58d (ARM: remove bunch of
now unused mach/io.h files) removed the orion5x io.h. Unfortunately,
this is still needed for the definition of IO_SPACE_LIMIT which
overrides the default 64K. All Orion based systems have 1Mbyte of IO
space per PCI[e] bus, and try to request_resource() this size. Orion5x
has two such PCI buses.

It is likely that the original, removed version, was broken. This
version might be less broken. However, it has not been tested on
hardware with a PCI card, let alone hardware with a PCI card with IO
capabilities.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'omap-fixes-a-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

From Paul Walmsley (as per Tony Lindgren's request):
 "Some uncontroversial OMAP clock, hwmod, and compiler warning fixes for 3.5-rc"

* tag 'omap-fixes-a-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
  ARM: OMAP2+: mux: fix sparse warning
  ARM: OMAP2+: CM: increase the module disable timeout
  ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
  ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
  ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
  ARM: OMAP: PM: Lock clocks list while generating summary

Merge tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
 reset. All of them are regression fixes, except for the missing omap2
 interrupt controller binding that somehow got missed earlier."

* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: Fix Beagleboard DVI reset gpio
  arm/dts: OMAP2: Fix interrupt controller binding
  ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
  ARM: OMAP2+: Fix MUSB ifdefs for platform init code

This driver contains version information that is outdated, has no real
value in terms of the Linux update process, and tends to confuse users.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

accessing first and last channel fails:
fakedata[0] is never accessed, out-of-bound access for last channel
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_iio_trigger(dev) instead of dev_get_drvdata(dev). Both will return the
trigger which belongs to the device, but the the first on is a bit more
lightweight.

Since this is the last location where we used dev_get_drvdata() for retrieving
the trigger there is no need anymore to assign the the trigger to the devices
drvdata, so we can remove that as well.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_iio_trigger(dev) instead of dev_get_drvdata(dev). Both will return the
trigger which belongs to the device, but the the first on is a bit more
lightweight. Also this will eventually free up the drvdata pointer of the device
for driver specific data.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The result of "foo = bar" is true, so in statements such as
  ...
  if((pDevice->bwextstep0 = TRUE)&&(param->u.wpa_key.key_index ==1))
  ...
an assignment  is most likely not what was intended - a comparison was. As in:
  ...
  if ((pDevice->bwextstep0 == TRUE) && (param->u.wpa_key.key_index == 1))
  ...

There are a 3 such mistakes in the iwctl_siwencodeext() function.
This patch fixes them all.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The header "rts51x.h" is included unconditionally at the start of the
file and then again once more under "#ifdef SUPPORT_FILE_OP".  Once is
enough, so remove the conditional include and just keep the
unconditional one.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed a coding style issue.
Signed-off-by: NErik Jones <erik@ejnode.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the pcmcia_disable_device() call where needed in the
pcmcia attach/detach and delete the dio700_release() function.

Move the logic of dio700_config() directly into the attach
function and properly return an error code when the config
fails.

Only set the pcmcia_cur_dev, used by the comedi_driver, if
the pcmcia attach is successful. Also, make sure to NULL it
in the detach.

Remove all the kernel messages in the pcmcia support code. They
are just added noise.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pcmcia suspend/resume callbacks don't do anything. Remove
them.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pcmcia device-specific data is not longer needed by this
driver. Remove it.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pcmcia support code in this driver appears to be cut-and-
paste from some other driver. It has code in it to stop the
device during suspend but nothing in the main comedi_driver
uses it.

Remove the 'stop' variable from the pcmcia private data and
all the logic that deals with it.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These messages should probably just be removed. For now just clean
then up.

Remove a couple redundant KERN_INFO messages in the pcmcia support
code and leave the dev_dbg() ones.

Change the dev_dgb() messages to use __func__ instead of the open
coded string.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comedi insn_config functions should return < 0 for errors or
the number of data elements used to perform the command, this value
is available as 'insn->n'. Return that instead of the open coded
number to better indicate what the return means.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'data[1] = ...' line is currently kept < 80 chars by breaking a pointer
access after the '->'. This makes the code a bit confusing to follow. Use
a local variable to shorten the line and make it clearer.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Functions don't need the ';' at the end.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need for the local variable 'iobase' in the attach
function. If it's '0' the attach fails otherwise the value is
just stored in dev->iobase.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the dev_printk() routines to output the kernel messages in the
attach routine.

The main 'attach' message had a level of KERN_ERR, I believe it should
have been KERN_INFO. Also, move that message to the end of the attach
so it only gets displayed if the attach is successful.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The irq code is not compiled in due to the '#ifdef incomplete'.
And, as stated, it's not even complete. Just remove it.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the contents of subdev_700_init into the attach function.
For aesthetic reasone, add some whitespace to the initialization
of the subdevice.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These defines are not referenced in the driver. Remove them.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver was originally copied from the 8255 driver. The 8255
uses a callback function to handle the io operations to the device.
In this driver, the callback adds unneeded complexity.

The CALLBACK_ARG for this driver is always 'dev->iobase' and the
CALLBACK_FUNC is always 'subdev_700_cb'.

The callback function is also overly complex for this driver.
It takes a 'dir' parameter to determine if the io is a write or
read, a 'port' parameter that is not used, a 'data' parameter
that is only used for writes, and an 'arg' which is the iobase
of the device.

Unwind all of it and just put the outb()/inb() call in the code
where needed.

This allows getting rid of the private data completely. Refactor
the code based on it's removal.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'have_irq' variable is not needed since this driver doesn't
use interrupts. Remove it.

The kfree(s->private) needs to remain to free the memory allocated
in subdev_700_init().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'thisboard' macro relies on a local variable having a specific
name and yields a pointer derived from that local variable.
Replace the macro with local variables and use the comedi_board()
helper to get the pointer.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetic reasons, move the boardinfo declaration down so it's
next to the comedi_driver. That's the only place in the driver
where it's referenced directly.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver is only used for pcmcia type devices. There is no need for
the 'bustype' check. Remove the variable from the boardinfo and refactor
the code based on it's removal.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>