Add "blue-and-red-wiring"-device tree property and update devicetree
binding document.

The red and blue components are reversed between 24 and 16 bit modes
on am335x LCDC output pins. To get 24 RGB format the red and blue
wires has to be crossed and this in turn causes 16 colors output to be
in BGR format. With straight wiring the 16 color is RGB and 24 bit is
BGR.

The new property describes whether the red and blue wires are crossed
or not. If the property is not present or its value is not recognized
the legacy mode is assumed. The legacy configuration supports RGB565,
RGB888 and XRGB8888 formats. However, depending on wiring, the red and
blue colors are swapped in either 16 or 24-bit color modes.

For more details see section 3.1.1 in AM335x Silicon Errata:
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Write DMA base and ceiling address with a single instruction, if
available. This should make it more unlikely that LCDC would fetch the
DMA addresses in the middle of an update. Having bad combination of
addresses in dma base and ceiling (e.g base > ceiling) can cause
unpredictaple behavior in LCDC.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

drm_helper_disable_unused_functions() should not be called by atomic
drivers.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This got accidentally dropped in the fixed commit and is required for
the driver to properly work on the rev1 IP, such as found on the LCDK.

Fixes: 2b2080d7 ("drm/tilcdc: Get rid of complex ping-pong mechanism")
Signed-off-by: NKarl Beldan <kbeldan@baylibre.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

The LCDC seems to expect its framebuffer ceiling address pointer to be
an inclusive bound.  The IP rev2 seems to cope with that but rev1 (as
found on the LCDK) don't.
Also note that this is what the framebuffer code does in da8xx-fb.c.

Since, as the TRM puts it, "The 2 LSBs are hardwired to 00b", the
dma_addr_t can be decremented without cast.
I tested it with a v2 (AM335x, rev  0x4F201000) and an LCDK (v1).
Signed-off-by: NKarl Beldan <kbeldan@baylibre.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

In function tilcdc_get_external_components the check for
the remote port parent is not correct. We need a '||' instead of
an '&&'.
Signed-off-by: NTeresa Remmet <t.remmet@phytec.de>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

This reverts commit d10571fc.

This isn't how we get to do this unfortunately.
Signed-off-by: NDave Airlie <airlied@redhat.com>

More -misc stuff
- moar drm_crtc.c split up&documentation
- some fixes for the simple kms helpers (Andrea)
- I included all the dri1 patches from David - we're not removing any code
  or drivers, and it seems to have worked as a wake-up call to motivate a
  few more people to upstream kms conversions for these. Feel free to
  revert if you disagree strongly.
- a few other single patches

* tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel: (24 commits)
  drm: drm_probe_helper: Fix output_poll_work scheduling
  drm: bridge/dw-hdmi: Fix colorspace and scan information registers values
  drm/doc: Polish docs for drm_property&drm_property_blob
  drm: Unify handling of blob and object properties
  drm: Extract drm_property.[hc]
  drm: move drm_mode_legacy_fb_format to drm_fourcc.c
  drm/doc: Polish docs for drm_mode_object
  drm: Remove drm_mode_object->atomic_count
  drm: Extract drm_mode_object.[hc]
  drm/doc: Polish kerneldoc for encoders
  drm: Extract drm_encoder.[hc]
  drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y
  drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit
  drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()
  drm/atomic-helper: Add atomic_disable CRTC helper callback
  drm: simple_kms_helper: add support for bridges
  drm: simple_kms_helper: make connector optional at init time
  drm/bridge: introduce bridge detaching mechanism
  drm/simple-helpers: Always add planes to the state update
  drm: reduce GETCLIENT to a minimum
  ...

drm_kms_helper_poll_enable_locked() should check if we have delayed event
pending and if we have, schedule the work to run without delay.

Currently the output_poll_work is only scheduled if any of the connectors
have DRM_CONNECTOR_POLL_CONNECT or DRM_CONNECTOR_POLL_DISCONNECT with
DRM_OUTPUT_POLL_PERIOD delay. It does not matter if we have delayed event
already registered to be handled. The detection will be delayd by
DRM_OUTPUT_POLL_PERIOD in any case.
Furthermore if none of the connectors are marked as POLL_CONNECT or
POLL_DISCONNECT because all connectors are either POLL_HPD or they are
always connected: the output_poll_work will not run at all even if we
have delayed event marked.

When none of the connectors require polling, their initial status change
from unknown to connected/disconnected is not going to be handled until
the first kms application starts or if we have fb console enabled.

Note that in general the output poll work should be enabled already
when this happens, but at driver load usually the first probe happens
before the output polling is enabled. This patch fixes this case.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
[danvet: Note when exactly this is an issue, since the probe code
schedules the poll work itself already.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160831110905.31289-1-peter.ujfalusi@ti.com

Colorspace and scan information values were being written in wrong
offsets. This patch corrects this and writes the values at the
offsets specified in the databook.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/96fd0f06b7ebc2ee5cb8239a99648f3107e24497.1471530573.git.joabreu@synopsys.com

- remove kerneldoc for drm-internal functions
- drm_property_replace_global_blob isn't actually atomic, and doesn't
  need to be. Update docs&comments to match
- document all the types and try to link things a bit better
- nits all over

v2: Appease checkpatch in the moved code (Archit)
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-9-daniel.vetter@ffwll.ch

They work exactly the same now, after the refcounting unification a bit
ago. The only reason they're distinct is backwards compat with existing
userspace.

Cc: Daniel Stone <daniels@collabora.com>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-8-daniel.vetter@ffwll.ch

This just contains the base property classes and all the code to
handle blobs. I think for any kind of standardized/shared properties
it's better to have separate files - this is fairly big already as-is.

v2: resurrect misplaced hunk (Daniel Stone)

Cc: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-7-daniel.vetter@ffwll.ch

It's part of the drm fourcc handling code, mapping the old depth/bpp
values to new fourcc codes.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-6-daniel.vetter@ffwll.ch

I figured an overview section here is overkill, and better
to just document the 2 structures themselves well enough.

v2: Review from Archit:
- Appease checkpatch in moved code.
- Spelling fixes in the kerneldoc.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-5-daniel.vetter@ffwll.ch

It's only used in drm_mode_object_get_properties, and we can compute
it there directly with a bit of code shuffling.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-4-daniel.vetter@ffwll.ch

Just for the struct drm_mode_object base class. The header file was
already partially extracted to help untangle the include loops.

v2:
- Also move the generic get/set property ioctls. At first this seemed
  like a bad idea since it requires making drm_mode_crtc_set_obj_prop
  non-static. But eventually that will get split away too (like
  the connector version already is) for both crtc and planes. Hence I
  reconsidered.

- drm_mode_object.[hc] instead of drm_modeset.[hc], which requires
  renaming the drm_modeset.h header I already started building up.
  This is more consistent (matches the name of the main structure),
  and I want to be able to use drm_modeset.[hc] for the basic modeset
  init/cleanup functionality like drm_mode_config_init.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-3-daniel.vetter@ffwll.ch

- Move missing bits into struct drm_encoder docs.
- Explain that encoders are 95% internal and only 5% uapi, and that in
  general the uapi part is broken.
- Remove verbose comments for functions not exposed to drivers.

v2: Review from Archit:
- Appease checkpatch in the moved code.
- Make it clearer that bridges are not exposed to userspace.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-2-daniel.vetter@ffwll.ch

Same treatment as before. Only hiccup is drm_crtc_mask, which
unfortunately can't be resolved until drm_crtc.h is less of a monster.
Untangle the header loop with a forward declaration for that static
inline.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-1-daniel.vetter@ffwll.ch

When CONFIG_DRM_KMS_FB_HELPER is disabled, we can have a configuration
in which some DRM drivers are built-in, but the framebuffer core is a
loadable module. This results in a link error, such as:

drivers/gpu/drm/radeon/radeon.o: In function `radeon_pci_probe':
radeon_kfd.c:(.text.radeon_pci_probe+0xbc): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/amd/amdgpu/amdgpu.o: In function `amdgpu_pci_probe':
amdgpu_mn.c:(.text.amdgpu_pci_probe+0xa8): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/mgag200/mgag200.o: In function `mga_vram_init':
mgag200_ttm.c:(.text.mga_vram_init+0xa8): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/mgag200/mgag200.o: In function `mga_pci_probe':
mgag200_ttm.c:(.text.mga_pci_probe+0x88): undefined reference to `remove_conflicting_framebuffers'
Makefile:969: recipe for target 'vmlinux' failed

This changes the compile-time check to IS_REACHABLE, which means we end up
not calling remove_conflicting_framebuffers() in the configuration, which
seems good enough, as we know that no framebuffer driver is loaded by the
time that the built-in DRM driver calls remove_conflicting_framebuffers.

We could alternatively avoid the link error by forcing CONFIG_FB to not
be a module in this case, but that wouldn't change anything at runtime,
and just make the already convoluted set of dependencies worse here.

I could not find out what happens if the fbdev driver gets loaded as
a module after the DRM driver is already initialized, but that is a case
that can happen with or without this patch.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 0a3bfe29 ("drm/fb-helper: Fix the dummy remove_conflicting_framebuffers")
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829123428.3260105-1-arnd@arndb.de
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com

Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com

Currently, the helper drm_atomic_helper_disable_planes_on_crtc() calls
->atomic_disable for all planes _to be_ enabled on a particular CRTC.
This is obviously wrong for those planes which are not scanning out frames
when the helper is called.  Instead, it's sane to disable active planes
of old_crtc_state in the helper.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472196644-30563-3-git-send-email-gnuiyl@gmail.com

Some display controllers need plane(s) to be disabled together with
the relevant CRTC, e.g., the IPUv3 display controller for imx-drm.
This patch adds atomic_disable CRTC helper callback so that
old_crtc_state(as a parameter of the callback) could be used
to get the active plane(s) of the old CRTC state for disable operation.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472196644-30563-2-git-send-email-gnuiyl@gmail.com

Introduce drm_simple_display_pipe_attach_bridge() and
drm_simple_display_pipe_detach_bridge() in order to make it possible to use
drm encoders with the simple display pipes managed by simple_kms_helpers
Suggested-by: NDaniel Vetter <daniel@ffwll.ch>
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-3-git-send-email-andrea.merello@gmail.com

drm_simple_display_pipe_init() pretends to attach a connector
to the display pipe.

In case a drm bridge has to be used, then it's the bridge that
takes care of connectors.

This patch makes the connector parameter optional for
drm_simple_display_pipe_init(), so that a drm bridge could
handle connector by itself later.
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-2-git-send-email-andrea.merello@gmail.com

Up to now, once a bridge has been attached to a DRM device, it cannot
be undone.

In particular you couldn't rmmod/insmod a DRM driver that uses a bridge,
because the bridge would remain bound to the first (dead) driver instance.

This patch fixes this by introducing drm_encoder_detach() and a ->detach
callback in drm_bridge_funcs for the bridge to be notified about detaches.

It's DRM/KMS driver responsibility to call drm_encoder_detach().

While adding the bridge detach callback, with its kerneldoc, I also added
kerneldoc for attach callback.

Few other kerneldocs fixes around there are included.
Suggested-by: NDaniel Vetter <daniel@ffwll.ch>
Suggested-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-1-git-send-email-andrea.merello@gmail.com

Our update function is hooked to the single plane, which might not get
called for crtc-only updates. Which is surprising, so fix this by
always adding the plane.

While at it document how&when the event should be sent out better in
the kerneldoc.

Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: andrea.merello@gmail.com
Tested-and-Reported-by: andrea.merello@gmail.com
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NNoralf Trønnes <noralf@tronnes.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471933540-31131-1-git-send-email-daniel.vetter@ffwll.ch

The *only* known user of GETCLIENT is libva, which uses it to check
whether its own context is authenticated. It used to iterate all clients,
look for one that matches its own pid and then check its state.

The entire purpose for us to still have a GETCLIENT implementation is to
serve libva. So lets not pretend we do anything else: Make this function
return information on the caller's context only, fake the PID to the
caller's pid so they always match, and just fill in the "authenticated"
bit, nothing else.

This patch reduces the complexity of GETCLIENT to a bare minimum, avoids
any dependency on priv->uid or priv->pid (allows us to get rid of them),
and makes libva happy by always *exactly* returning the information it
wants.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160825143505.7447-1-dh.herrmann@gmail.com

The legacy DRI1 drivers expose highly broken interfaces to user-space. No
modern system should enable them, or you will effectively allow user-space
to circumvent most of your kernel security measures. The DRI1 kernel APIs
are simply broken.

User-space can always use vesafb/efifb/simplefb and friends to get working
graphics.

Lets hide the old drivers behind CONFIG_BROKEN. In case they turn out to
be still used (really?), we can easily revert this and figure out a way to
move them out of sight (e.g., moving all DRI1 drivers to
drivers/gpu/dri1/).
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160804080657.9664-2-dh.herrmann@gmail.com

Lets move forward and hide the remaining DRI1 drivers behind a config
option, so we have a central place to disable them all. Furthermore, we
can provide a clear warning to anyone enabling them.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160804080657.9664-1-dh.herrmann@gmail.com

First drm-next pull for radeon and amdgpu for 4.9.  Highlights:
- powerplay support for iceland asics
- improved GPU reset (both full asic and per block)
- UVD and VCE powergating for CZ and ST
- VCE clockgating for CZ and ST
- Support for pre-initialized (e.g., zeroed) vram buffers
- ttm cleanups
- virtual display support
- core and radeon/amdgpu support for page_flip_target
- lots of bug fixes and clean ups

* 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux: (171 commits)
  drm/amdgpu: use memcpy_toio for VCE firmware upload
  drm/amdgpu: use memcpy_to/fromio for UVD fw upload
  drm/amd/powerplay: delete useless code in iceland_hwmgr.c.
  drm/radeon: switch UVD code to use UVD_NO_OP for padding
  drm/amdgpu: switch UVD code to use UVD_NO_OP for padding
  drm/radeon: add support for UVD_NO_OP register
  drm/amdgpu: add support for UVD_NO_OP register
  drm/amdgpu: fix VCE ib alignment value
  drm/amdgpu: fix IB alignment for UVD
  drm/amd/amdgpu: Print ring name in amdgpu_ib_schedule()
  drm/radeon: remove dead code, si_mc_load_microcode (v2)
  drm/radeon/cik: remove dead code (v2)
  drm/amd/powerplay: avoid NULL dereference, cz_hwmgr.c
  drm/amd/powerplay: avoid NULL pointer dereference
  drm/amdgpu/gmc8: remove dead code (v2)
  drm/amdgpu/gmc7: remove dead code (v2)
  drm/amdgpu: Fix indentation in dce_v8_0_audio_write_sad_regs()
  drm/amdgpu: Use correct mask in dce_v8_0_afmt_setmode() and fix comment typos.
  drm/amdgpu: cleanup amdgpu_vm_bo_update params
  drm/amdgpu: stop adding dummy entry in amdgpu_ttm_placement_init
  ...

drm-intel-next-2016-08-22:
- bugfixes and cleanups for rcu-protected requests (Chris)
- atomic modeset fixes for gpu reset on pre-g4x (Maarten&Ville)
- guc submission improvements (Dave Gordon)
- panel power sequence cleanup (Imre)
- better use of stolen and unmappable ggtt (Chris), plus prep work to make that
  happen
- rework of framebuffer offsets, prep for multi-plane framebuffers (Ville)
- fully partial ggtt vmaps, including fenced ones (Chris)
- move lots more of the gem tracking from the object to the vma (Chris)
- tune the command parser (Chris)
- allow fbc without fences on recent platforms (Chris)
- fbc frontbuffer tracking fixes (Chris)
- fast prefaulting using io-mappping.h pgprot caching (Chris)

* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (141 commits)
  io-mapping: Fixup for different names of writecombine
  io-mapping.h: s/PAGE_KERNEL_IO/PAGE_KERNEL/
  drm/i915: Update DRIVER_DATE to 20160822
  drm/i915: Use remap_io_mapping() to prefault all PTE in a single pass
  drm/i915: Embed the io-mapping struct inside drm_i915_private
  io-mapping: Always create a struct to hold metadata about the io-mapping
  drm/i915/fbc: Allow on unfenced surfaces, for recent gen
  drm/i915/fbc: Don't set an illegal fence if unfenced
  drm/i915: Flush delayed fence releases after reset
  drm/i915: Reattach comment, complete type specification
  drm/i915/cmdparser: Accelerate copies from WC memory
  drm/i915/cmdparser: Use binary search for faster register lookup
  drm/i915/cmdparser: Check for SKIP descriptors first
  drm/i915/cmdparser: Compare against the previous command descriptor
  drm/i915/cmdparser: Improve hash function
  drm/i915/cmdparser: Only cache the dst vmap
  drm/i915/cmdparser: Use cached vmappings
  drm/i915/cmdparser: Add the TIMESTAMP register for the other engines
  drm/i915/cmdparser: Make initialisation failure non-fatal
  drm/i915: Stop discarding GTT cache-domain on unbind vma
  ...

This pull request contains the following rockchip drm changes:

  - Introduce support for rk3399 vop/crtc
  - Add PSR framework to the rockchip driver
  - Implement PSR in the rockchip analogix edp driver
  - Fix panel on/off in analogix to avoid damaging panels
  - Some miscellaneous fixes to clean up logs and code readability

* 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood:
  drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print
  drm/rockchip: Enable vblank without event
  drm/rockchip: Improve analogix-dp psr handling
  drm/rockchip: A couple small fixes to psr
  drm/rockchip: Use a spinlock to protect psr state
  drm/rockchip: Don't use a delayed worker for psr state changes
  drm/rockchip: Convert psr_list_mutex to spinlock and use it
  drm/rockchip: analogix_dp: implement PSR function
  drm/bridge: analogix_dp: add the PSR function support
  drm/rockchip: add an common abstracted PSR driver
  drm/rockchip: vop: export line flag function
  drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared
  dt-bindings: add compatible strings for big/little rockchip vops
  dt-bindings: sort Rockchip vop compatible by chip's number
  drm/rockchip: vop: add rk3399 vop support
  drm/rockchip: vop: introduce VOP_REG_MASK
  drm/rockchip: sort registers define by chip's number

Try to be clean here, even when it's a noop on x86.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Also use the firmware size from the header instead of calculating it.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Replace packet2's with packet0 writes to UVD_NO_OP.  The
value written to UVD_NO_OP does not matter.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Replace packet2's with packet0 writes to UVD_NO_OP.  The
value written to UVD_NO_OP does not matter.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Writes to this register are the preferred way to do NOPs.

Bump the driver version as well.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Writes to this register are the preferred way to do NOPs.

Bump the driver version as well.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>