Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 12 7月, 2014 1 次提交
    • J
      ipv6: addrconf: implement address generation modes · bc91b0f0
      由 Jiri Pirko 提交于 
      This patch introduces a possibility for userspace to set various (so far
two) modes of generating addresses. This is useful for example for
NetworkManager because it can set the mode to NONE and take care of link
local addresses itself. That allow it to have the interface up,
monitoring carrier but still don't have any addresses on it.

One more use-case by Dan Williams:
<quote>
WWAN devices often have their LL address provided by the firmware of the
device, which sometimes refuses to respond to incorrect LL addresses
when doing DHCPv6 or IPv6 ND.  The kernel cannot generate the correct LL
address for two reasons:

1) WWAN pseudo-ethernet interfaces often construct a fake MAC address,
or read a meaningless MAC address from the firmware.  Thus the EUI64 and
the IPv6LL address the kernel assigns will be wrong.  The real LL
address is often retrieved from the firmware with AT or proprietary
commands.

2) WWAN PPP interfaces receive their LL address from IPV6CP, not from
kernel assignments.  Only after IPV6CP has completed do we know the LL
address of the PPP interface and its peer.  But the kernel has already
assigned an incorrect LL address to the interface.

So being able to suppress the kernel LL address generation and assign
the one retrieved from the firmware is less complicated and more robust.
</quote>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bc91b0f0
  3. 05 6月, 2014 1 次提交
  5. 24 5月, 2014 1 次提交
    • S
      net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool. · ed616689
      由 Sucheta Chakraborty 提交于 
      o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ed616689
  7. 01 4月, 2014 1 次提交
  9. 24 1月, 2014 2 次提交
  11. 23 1月, 2014 2 次提交
  13. 18 1月, 2014 1 次提交
  15. 04 1月, 2014 3 次提交
  17. 20 12月, 2013 5 次提交
  19. 18 12月, 2013 5 次提交
  21. 14 12月, 2013 8 次提交
  23. 01 12月, 2013 1 次提交
  25. 04 11月, 2013 1 次提交
    • A
      net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0) · f421436a
      由 Arvid Brodin 提交于 
      High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.

HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.

This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).
Signed-off-by: NArvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f421436a
  27. 20 10月, 2013 2 次提交
  29. 01 9月, 2013 1 次提交
  31. 31 7月, 2013 1 次提交
  33. 14 6月, 2013 1 次提交
  35. 11 6月, 2013 2 次提交
  37. 29 4月, 2013 1 次提交