The MDIO PM operations are really PHY device PM operations. So move
them into phy_device. This will be needed when we support devices on
the mdio bus which are not PHYs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mdio_bus exports three attributes:

- PHY ID is the unique 32-bits identifier for a MDIO device implementing
  standard MII registers MII_PHYSID1/2, which is not guaranteed to be the
  case for non-standard compliant devices (e.g: Ethernet switches)

- PHY interface describes the data-path of the PHY/MDIO device, which is
  not strictly a PHY thing, but is required and needed for PHY devices to
  function, a MDIO device could be a control device exclusively

- PHY has fixups describes what the PHY driver may have done, so
  completely PHY specific

These are all phy attributes, not generic mdio attributes. So move the
attributes into the phy device code.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than use devm_kzalloc(), use the mdio helper function.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the open coded search for the first phy with a call to the
existing helper function.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we have a phydev, make use of it and the phy_read() function.
This will help with later refactoring.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NBingkuo Liu <bingkuol@vmware.com>
Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The WeTelecom-WPD600N is an LTE module that, in addition to supporting most
"normal" bands, also supports LTE over 450MHz. Manual testing showed that
only interface number three replies to QMI messages.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"priv" is allocated with devm_kzalloc() so freeing it here with kfree()
will lead to a double free.

Fixes: 39339616 ('fsl/fman: Add FMan MAC driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pause_time is unsigned so it can't be less than zero.  The bug means
that we allow invalid pause-times.

Fixes: 57ba4c9b ('fsl/fman: Add FMan MAC support')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We checked "err" on the lines before so we know it's zero here.

These cause a static checker warning because checking known things can
indicate a bug.  Maybe there is a missing assignment or we are checking
the wrong variable.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit d79f16c0 fixed a user triggerable
scribble on free memory but added a new one which allows the user to
scribble even more and user controlled data into freed space.

As with 6pack we need to halt the queue before we free the buffers, because
the transmit logic is not protected by the semaphore.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is based on the work done by Przemek Rudy in bug 70761 at
bugzilla.kernel.org, but with some work done to disentagle and clarify
things a bit.

Similar to Przemek's work and other drivers, we're adding a padding of 16
here, but we're also disentangling mtu size calculations from max buffer
size calculations a bit, and adding ETH_HLEN to the value written into
ALX_MTU. Hopefully, with a bit more consistency and clarity, things behave
better here. Sadly, I can only test in my alx-driven E2200, which worked
just fine before this patch.

In comment #58 of bug 70761, Eugene A. Shatokhin reports that this patch
does help considerably for a ROSA Linux user of his with an AR8162 network
adapter when patched into a 4.1.x-based kernel, with several days of
normal operation where wired network previously wasn't usable without
setting MTU to 9000 as a work-around.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
CC: "Eugene A. Shatokhin" <eugene.shatokhin@rosalab.ru>
CC: Przemek Rudy <prudy1@o2.pl>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a vlan is been configured, remeber the untagged mode of the vlan.
When displaying the list of configured VLANs, show the untagged attribute.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a port is bridged, the bridge must be vlan aware bridge (.1Q)
or the bridging should be on top of VLAN interfaces (.1D bridge).
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize VLANs 0..4095 (Remove init for VID 4096).
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit acf673a3 fixed a user triggerable free
memory scribble but in doing so replaced it with a different one that allows
the user to control the data and scribble even more.

sixpack_close is called by the tty layer in tty context. The tty context is
protected by sp_get() and sp_put(). However network layer activity via
sp_xmit() is not protected this way. We must therefore stop the queue
otherwise the user gets to dump a buffer mostly of their choice into freed
kernel pages.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During initialization, when creating the send descriptor queues (SDQs),
we specify the CPU egress traffic class of each SDQ. The maximum number
of classes of this type is different in the two ASICs supported by this
PCI driver.

New firmware versions check this value is set correctly, which causes
errors on the Spectrum ASIC, as its max exposed egress traffic class is
lower than 7.

Solve this by setting this field to 3, which is an acceptable value for
both ASICs.

Note that we currently do not expose the QoS capabilities of the ASICs,
so setting this to an hardcoded value is OK for now.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc fails to see that the use of the 'last_offset' variable
in hns_nic_reuse_page() is used correctly and issues a bogus
warning:

drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_nic_reuse_page':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:541:6: warning: 'last_offset' may be used uninitialized in this function [-Wmaybe-uninitialized]

This simplifies the function to make it more obvious what is
going on to both readers and compilers, which makes the warning
go away.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a PHC support to the mlx5_en driver. Use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled.  This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.

The driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-4 card.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for enable/disable HW timestamping for incoming and/or
outgoing packets. To enable/disable HW timestamping appropriate
ioctl should be used. Currently HWTSTAMP_FILTER_ALL/NONE and
HWTSAMP_TX_ON/OFF only are supported. Make all relevant changes in
RX/TX flows to consider TS request and plant HW timestamps into
relevant structures.

Add internal clock for converting hardware timestamp to nanoseconds. In
addition, add a service task to catch internal clock overflow, to make
sure timestamping is accurate.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the SKB is cloned, or has an elevated users count, someone else
can be looking at it at the same time.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commands run in a vrf context are not failing as expected on a route lookup:
    root@kenny:~# ip ro ls table vrf-red
    unreachable default

    root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
    ping: Warning: source address might be selected on device other than vrf-red.
    PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.

    --- 10.100.1.254 ping statistics ---
    2 packets transmitted, 0 received, 100% packet loss, time 999ms

Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:

    root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
    connect: No route to host
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.

Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.

Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cphy_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ARM allmodconfig fails because of the addition of the FMAN driver:

drivers/built-in.o: In function `dtsec_restart_autoneg':
binder.c:(.text+0x173328): undefined reference to `mdiobus_read'
binder.c:(.text+0x173348): undefined reference to `mdiobus_write'
drivers/built-in.o: In function `dtsec_config':
binder.c:(.text+0x173d24): undefined reference to `of_phy_find_device'
drivers/built-in.o: In function `init_phy':
binder.c:(.text+0x1763b0): undefined reference to `of_phy_connect'
drivers/built-in.o: In function `stop':
binder.c:(.text+0x176014): undefined reference to `phy_stop'
drivers/built-in.o: In function `start':
binder.c:(.text+0x176078): undefined reference to `phy_start'

The reason is that the driver uses PHYLIB, but that is a loadable
module here, and fman itself is built-in.

This patch makes it possible to configure fman as a module as well
so we don't change the status of PHYLIB in an allmodconfig kernel,
and it adds a 'select PHYLIB' statement to ensure that phylib is
always built-in when fman is.

The driver uses "builtin_platform_driver(fman_driver);", which means
it cannot be unloaded, but it's still possible to have it as a loadable
module that gets loaded once and never removed.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 5adae51a ("fsl/fman: Add FMan MURAM support")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>