The change enables offloading TCP checksum calculation to firmware.
There are still some issues with the checksum offload so better to
disable it by default until the issues are resolved.

To enable TCP checksum offload for tx and rx paths, use
the ethtool as follows:
ethtool -K <interface> tx on
ethtool -K <interface> rx on

To disable TCP checksum offload, for tx and rx paths, use
the ethtool as follows:
ethtool -K <interface> tx off
ethtool -K <interface> rx off

kvalo: indentation changes
Signed-off-by: NRishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is needed to fix current hostapd/wpa_supplicant AP operations for
frame registration. P2P GO mode already advertised these, but AP mode
was forgotten and could not be used after the hostapd/wpa_supplicant
frame registration changes.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

hostapd/wpa_supplicant AP mode uses this operation to flush the station
entries. Implement this in ath6kl to avoid unnecessary warnings from
NL80211_CMD_DEL_STATION failing.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cfg80211 could pass a NULL net_device to the driver via the
set_channel() callback, when it receives a request to set the
device's channel. Not handling this case properly results in this panic:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000cb0
IP: [<ffffffffa0374e49>] ath6kl_cfg80211_ready+0x9/0x70 [ath6kl_sdio]

Call Trace:
[<ffffffffa0374ed7>] ath6kl_set_channel+0x27/0x90 [ath6kl_sdio]
[<ffffffffa04dfd5f>] cfg80211_set_freq+0xff/0x1d0 [cfg80211]
[<ffffffffa04d3275>] ? nl80211_set_wiphy+0x85/0x660 [cfg80211]
[<ffffffffa04d3198>] __nl80211_set_channel.isra.39+0x118/0x140 [cfg80211]
[<ffffffffa04d34f3>] nl80211_set_wiphy+0x303/0x660 [cfg80211]
[<ffffffff813678d7>] ? rtnl_lock+0x17/0x20
[<ffffffffa04ca165>] ? nl80211_pre_doit+0xb5/0x150 [cfg80211]
[<ffffffff81382a45>] genl_rcv_msg+0x1d5/0x250
[<ffffffff81382870>] ? genl_rcv+0x40/0x40
[<ffffffff81381be9>] netlink_rcv_skb+0xa9/0xd0
[<ffffffff81382855>] genl_rcv+0x25/0x40
[<ffffffff811354f0>] ? might_fault+0x40/0x90
[<ffffffff81381519>] netlink_unicast+0x2d9/0x320
[<ffffffff813818e6>] netlink_sendmsg+0x2c6/0x320
[<ffffffff81343800>] ? sock_update_classid+0xb0/0x110
[<ffffffff8133f52e>] sock_sendmsg+0x10e/0x130
[<ffffffff81169933>] ? mem_cgroup_update_page_stat+0x193/0x250
[<ffffffff811354f0>] ? might_fault+0x40/0x90
[<ffffffff811354f0>] ? might_fault+0x40/0x90
[<ffffffff81135539>] ? might_fault+0x89/0x90
[<ffffffff811354f0>] ? might_fault+0x40/0x90
[<ffffffff8134d126>] ? verify_iovec+0x56/0xd0
[<ffffffff8133f9e6>] __sys_sendmsg+0x396/0x3b0
[<ffffffff8108e823>] ? up_read+0x23/0x40
[<ffffffff81040e68>] ? do_page_fault+0x208/0x4e0
[<ffffffff81193151>] ? vfsmount_lock_local_unlock+0x21/0x60
[<ffffffff811947d0>] ? mntput_no_expire+0x30/0xe0
[<ffffffff8119489f>] ? mntput+0x1f/0x30
[<ffffffff81342149>] sys_sendmsg+0x49/0x90
[<ffffffff81425482>] system_call_fastpath+0x16/0x1b
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As firmware starting from 3.2.0.12 has some API changes and doesn't work
with older versions of ath6kl we need to bump up the API version. This
way we don't break anything.

Also store which version of API is used and print that during boot:

ath6kl: ar6003 hw 2.1.1 sdio fw 3.2.0.13 api 3
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ath6kl has just hardcoded paths to each firmware file. Change
this more dynamic by separating the the directory and file name from each
other. That way it's easier to dynamically create full paths to firmware and
code looks better. And now it's possible to remove a function needed by
devicetree code.

While at it add a structure inside struct ath6kl_hw to contain all
firmware names. I deliberately omitted board file support as
those will be handled later.

This is needed for firmware API 3.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware ARP module requires own IP addr in order to respond
to the outside world when the target is in WOW suspend state.

At present, firmware ARP module has capability to hold 2 IP addr.
So, WOW mode will be disabled if the total IP addr configured in
net_dev for our device is greater than firmware limit (MAX_IP_ADDRS)
which is 2 at this moment.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In this way, caller is free to pass only the value of IP addr
to configure.

In addition to this,
  * 'ips' variable data type in struct wmi_set_ip_cmd is changed
     from __le32 to __be32 in order to match network byte order.
  *  ipv4_is_multicast() is used to validate multicast ip addr.
  *  New argument if_idx is added to supply correct vif index
     to ath6kl_wmi_cmd_send().

This will be used in the next patch.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Empty IE buffer means that the new association is not supposed to
include extra IEs. Make sure any previously configured (Re)Association
Request frame IEs get cleared in such a case. This is based on a patch
from Shuibing.

Cc: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to avoid the scenario where the bss entry of the AP got
expired when reporting roaming event to current AP. As the bss
entry for the current bss is available in driver, pass this bss
to cfg80211. This fixes WARNING: at net/wireless/sme.c:586.

This patch depends on the following patch in cfg80211
"cfg80211: Fix race in bss timeout".
Reported-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

its not used anywhere in the current code
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

before concluding that the recieved beacon is for us, let us make sure
that the BSSID is non-zero. when I configured ad-hoc mode as creator and
left it for some time without joining I found we recieved few frames whose
BSSID is zero, which we concluded wrongly as 'my_beacons'
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This initial DFS module provides basic functionality to deal
with radar pulses reported by the Atheros DFS HW pulse detector.

The reported data is evaluated and basic plausibility checks
are performed to filter false pulses. Passing radar pulses are
forwarded to pattern detectors which are not yet implemented.

(Some modifications to actually use ATH9K_DFS_DEBUGFS based on comments
from Julian Calaby <julian.calaby@gmail.com>. -- JWL)
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to enable DFS upstream we want to be sure
DFS has been tested for each chipset. Push for public
documentation of the requirements we want in place and
allow for enabling each chipset through a single upstream
commit.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This can later be used by other drivers that implement
DFS support.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A debug level was added to the ath module for printing
MCI messages but no documentation was provided. Clarify that
MCI is the Message Coexistence Interface, a private protocol
used exclusively for WLAN-BT coexistence starting from
AR9462.

Cc: wtsao@qca.qualcomm.com
Cc: rmanohar@qca.qualcomm.com
Cc: mohammed@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The receiver will discard them anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of releasing and taking back the lock over and over again in the
tx path, hold the lock a bit longer, requiring much fewer lock/unlock pairs.
This makes locking much easier to review and should not have any noticeable
performance/latency impact.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tid->seq_next is initialized on A-MPDU start anyway, and the comment next
to this chunk of code seems to be bogus as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When processing A-MPDU tx status, only send a BAR for the failed packet
with the highest sequence number.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of limiting a subframe to 10 A-MPDU software transmission attempts,
count hardware retransmissions as well and raise the limit a bit. That way
there will be fewer software retransmission attempts when traffic suffers
from lots of hardware retransmissions.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables support for doing P2P management operations like device
discovery on top of a station interface. After group formation, the station
interface will become a P2P GO/client interface as the case may be.

This feature requires modifications to a couple of existing WMI structures and
therefore new command ids and structures have been defined in order to be
compatible with older firmware versions and other chips. The exception here is
the wmi_connect_cmd. Adding a new field to the end of the structure will not
cause any issues with previous firmware versions since firmware only checks for
minimum length of the command. The other structures are of variable length,
hence it was not possible to add new fields to the end.

The new command ids have to be added to the end of enum wmi_cmd_id, so it has
updated to match the firmware.

The driver will support both the 'old' and the 'new' commands for a while by
checking the firmware capabilities.
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

AR6003 family use uart_tx=8 and refclk=26Mhz by default, and AR6004 family
uses different uart_tx pin and could also support various xtal source,
moves these per hw configuration.
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the regulatory got updated by country IE for the world
roaming cards, need to reconfigure the tx power immediately to
increase the power level.
Reviewed-by: NSam Leffler <sleffler@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we receive a country IE hint and we have a world roaming card
we can optimize output power further by ensuring that we use the
calibrated data for the country by using that country's own CTL data.
That is -- when world roaming and when we process a country IE we
no longer need to use the lowest output power of all CTLs instead
we use an optimized CTL output power for that specific country.

We accomplish this by copying the regulatory data prior on init
and restoring it when cfg80211 tells us it gets a core hint. Core
hints are only sent on init and when it wants to restore reguulatory
settings. We take advantage of this fact and apply the cached
regulatory data when we get a core hint. When we get a country IE
hint though we process the regulatory data as if programmed for
a specific country.
Tested-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This has no functional change. The helper can be used later
for other things like country IE changes and following the CTL
for different countries.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

in my previous patches of handling MCI interrupt I overlooked
the case of interrupt status/mask variable being zeroed out in
the below code, so ath_isr does not cache the MCI interrupt
in the intrstatus. finally MCI interrupt handling won't be
handled in ath9k_tasklet for the scheduled interrupts.
Fix this by moving the MCI interrupt code in the appropriate
position in ar9003_hw_get_isr

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

in ar9003_hw_get_isr we bail out if we don't have any primary
interrupts and synchronous interrupts, also make sure we don't
have any asynchronous interrupts
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath6kl firmware supports scheduled scan functionality with the wow ssid
filter. But the firmware does not send any events after scan results
so I had to add a timer which notifies about new scan results.

Sched scan needs firmware version 3.2.0.6 or later. If firmware doesn't
support sched scan the driver will not enable the feature.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For some strange reason I used ALIGN() to calculate index to the
buffer. That is totally bogus and wouldn't work when it tried to read
the second bit. Fix it by removing the ALIGN() altogether.

Also check that ie_len is not too short.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

According to the firmware engineers WOW_FILTER_SSID is actually the
second bit, not the first.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During suspend we need to stop all vifs, not just the first.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This way it's possible to keep all disconnect logic in one function and
easier to add new functionality, like stopping scheduled scan.

There are some changes to commands called during network interface close,
but there should not be any visible changes in functionality.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There's a workaround in ath6kl_cfg80211_stop() which emits disconnected
even when sme_state was disconnected. This is legacy from the old
staging driver and I can't repoduce the old problem anymore. I assume the
bug got fixed while the driver was cleaned up so let's get
rid of the hack.

This makes it possible to call ath6kl_cfg80211_stop from ath6kl_close()
which happens in a followup patch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It really should not return a void pointer. Also remove useless casts
from its users.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is needed to allow WAPI AP to configure the initial group key
to the target in the same way as is done with TKIP/CCMP. This
fixes broadcast data frame delivery with the initial group key.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The stations always chooses 1Mbps for all trasmitting frames,
whenever the AP is configured to lock the supported rates.
As the max phy rate is always set with the 4th from highest phy rate,
this assumption might be wrong if we have less than that. Fix that.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Reported-by: NAjay Gummalla <agummalla@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>