pr_debug() calls in the 'hot' *_mask(), *_unmask(), *_ack() and
get_irq() makes adding #define DEBUG pretty much useless.  Remove
these calls because they completely swamp the output.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>

The MPC5200 PSC device is wired up to a dedicated interrupt line
which is never shared.  This patch removes the IRQF_SHARED flag
from the request_irq() call which eliminates the "IRQF_DISABLED
is not guaranteed on shared IRQs" warning message from the console
output.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>

Trim out obsolete/extraneous properties and tighten up some usage
conventions.  Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
  nodes
- Move common interrupt-parent property out of device nodes and
  into top level parent node.

This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness.  Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>

There is no reason for the PSC UART driver or the Ethernet driver
to require a device_type property.  The compatible value is sufficient
to uniquely identify the device.  Remove it from the driver.

The whole 'port-number' scheme for assigning numbers to PSC uarts was
always rather half baked and just adds complexity.  Remove it from the
driver.  After this patch is applied, PSC UART numbers are simply
assigned from the order they are found in the device tree (just like
all the other devices).  Userspace can query sysfs to determine what
ttyPSC number is assigned to each PSC instance.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI hotplug: Change link order of pciehp & acpiphp
  PCI hotplug: fakephp: Allocate PCI resources before adding the device
  PCI MSI: Fix undefined shift by 32
  PCI PM: Do not wait for buses in B2 or B3 during resume
  PCI PM: Power up devices before restoring their state
  PCI PM: Fix hibernation breakage on EeePC 701
  PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
  PCI PM: Fix suspend error paths and testing facility breakage

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: fix per cpu kmem_cache_cpu array memory leak
  kmalloc: return NULL instead of link failure

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
  powerpc: Fix oops on some machines due to incorrect pr_debug()
  powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
  powerpc/5200: update device tree binding documentation
  powerpc/5200: Bugfix for PCI mapping of memory and IMMR
  powerpc/5200: update defconfigs

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched_rt: don't use first_cpu on cpumask created with cpumask_and
  sched: fix buddie group latency
  sched: clear buddies more aggressively
  sched: symmetric sync vs avg_overlap
  sched: fix sync wakeups
  cpuset: fix possible deadlock in async_rebuild_sched_domains

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (45 commits)
  V4L/DVB (10411): s5h1409: Perform s5h1409 soft reset after tuning
  V4L/DVB (10403): saa7134-alsa: saa7130 doesn't support digital audio
  V4L/DVB (10229): ivtv: fix memory leak
  V4L/DVB (10385): gspca - main: Fix memory leak when USB disconnection while streaming.
  V4L/DVB (10325): em28xx: Fix for fail to submit URB with IRQs and Pre-emption Disabled
  V4L/DVB (10317): radio-mr800: fix radio->muted and radio->stereo
  V4L/DVB (10314): cx25840: ignore TUNER_SET_CONFIG in the command callback.
  V4L/DVB (10288): af9015: bug fix: stick does not work always when plugged
  V4L/DVB (10287): af9015: fix second FE
  V4L/DVB (10270): saa7146: fix unbalanced mutex_lock/unlock
  V4L/DVB (10265): budget.c driver: Kernel oops: "BUG: unable to handle kernel paging request at ffffffff
  V4L/DVB (10261): em28xx: fix kernel panic on audio shutdown
  V4L/DVB (10257): em28xx: Fix for KWorld 330U Board
  V4L/DVB (10256): em28xx: Fix for KWorld 330U AC97
  V4L/DVB (10254): em28xx: Fix audio URB transfer buffer race condition
  V4L/DVB (10250): cx25840: fix regression: fw not loaded on first use
  V4L/DVB (10248): v4l-dvb: fix a bunch of compile warnings.
  V4L/DVB (10243): em28xx: fix compile warning
  V4L/DVB (10240): Fix obvious swapped names in v4l2_subdev logic
  V4L/DVB (10233): [PATCH] Terratec Cinergy DT XS Diversity new USB ID (0ccd:0081)
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  pxamci: enable DMA for write ops after CMD/RESP
  pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
  ricoh_mmc: Use suspend_late/resume_early
  mmci: Add support for ST Micro derivate
  mmc: Add a MX2/MX3 specific SDHC driver

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  icside: fix PCB version 6 support (v2)
  tx4939ide: typo fix and minor cleanup
  ide: add CS5536 host driver (v3)
  ide: Force VIA IDE legacy interrupts for AmigaOne boards
  IDE: Unregister and disable devices if initialization fails.
  ide: fix ide_register_port() failure handling
  ide: struct device - replace bus_id with dev_name(), dev_set_name()
  ide-cd: fix DMA for non bio-backed requests

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
  uwb: lock rc->rsvs_lock with spin_lock_bh()
  wusb: timeout when waiting for ASL/PZL updates in whci-hcd
  uwb: remove unused #include <version.h>'s
  wusb: return -ENOTCONN when resetting a port with no connected device
  uwb: safely remove all reservations

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: add text file detailing queue/ sysfs files
  bio.h: If they MUST be inlined, then use __always_inline
  Fix misleading comment in bio.h
  block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT
  block: fix oops in blk_queue_io_stat()

The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.

However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.

Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Current refcounting for modules (done if CONFIG_MODULE_UNLOAD=y) is
using a lot of memory.

Each 'struct module' contains an [NR_CPUS] array of full cache lines.

This patch uses existing infrastructure (percpu_modalloc() &
percpu_modfree()) to allocate percpu space for the refcount storage.

Instead of wasting NR_CPUS*128 bytes (on i386), we now use
nr_cpu_ids*sizeof(local_t) bytes.

On a typical distro, where NR_CPUS=8, shiping 2000 modules, we reduce
size of module files by about 2 Mbytes. (1Kb per module)

Instead of having all refcounters in the same memory node - with TLB misses
because of vmalloc() - this new implementation permits to have better
NUMA properties, since each  CPU will use storage on its preferred node,
thanks to percpu storage.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.

If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.

related to PXA270 Erratum #91
Tested-by: NVernon Sauder <VernonInHand@gmail.com>
Signed-off-by: NCliff Brake <cbrake@bec-systems.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NCliff Brake <cbrake@bec-systems.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.

Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: NPhilip Langdale <philipl@overt.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: NLinus Walleij <linus.walleij@ericsson.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

We need to pass struct ide_port_info also to ide_host_register().

v2:
Fix v5/v6 mismatch noticed by Russell.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.

Changes done while at it:

* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
  (chipset uses shared PIO/MWDMA timings).

* Fix cable detection to report 80-wires cable if BIOS set it for any
  device on a port (IDE core will do drive-side cable detection later).

* Don't disable UDMA while programming PIO timings.

* Simplify PCI/MSR support.

Pros of having IDE host driver in addition to libata's one:

* IDE is much lighter than SCSI+libata, the host driver itself is also
  a bit smaller:

   text    data     bss     dec     hex filename
   1261     496       4    1761     6e1 drivers/ata/pata_cs5536.o
   1242     128       4    1374     55e drivers/ide/cs5536.o

* This allows use of IDE features which are unavailable under libata.

v2:
* Fixes per review from Sergei:
  - simplify dependency check in Kconfig
  - use IDE_DRV_MASK also for ->drive_data
  - disable UDMA when programming MWDMA
  - program new DTC timings only when necessary
  - fix printk() level in cs5536_init_one()

* Fix patch description according to comments from Alan and Sergei.

v3:
* Smarter masking of UDMA bits per Sergei's suggestion.

Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: NGerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out port freeing from ide_host_free() to ide_free_port().

* Add ide_disable_port() and use it on ide_register_port() failure.

Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: linux-ide@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=12320.
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into for-upstream

Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

bvec_kmap_irq() and bvec_kunmap_irq() comments say they MUST be inlined,
so mark them as __always_inline.
Signed-off-by: NAlberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The comment says "remember to add offset!", but the function already adds
it.
Signed-off-by: NAlberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Some initial probe requests don't have disk->queue mapped yet, so we
can't rely on a non-NULL queue in blk_queue_io_stat(). Wrap it in
blk_do_io_stat().
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Since the complete re-write in 2.6.10, some PowerMacs (At least PowerMac 5500
and PowerMac G3 Beige rev A) with ATI Mach64 chip have suffered from unstable
columns in their framebuffer image. This seems to depend on a value (4) read
from PLL_EXT_CNTL register, which leads to incorrect DSP config parameters to
be written to the chip. This patch uses a value calculated by aty_init_pll_ct
instead, as a starting point.

There are questions as to whether this should be extended to other platforms
or maybe made dependent on specific chip types, but in the meantime, this has
been tested on various powermacs and works for them so let's commit it.
Signed-off-by: NRisto Suominen <Risto.Suominen@gmail.com>
Tested-by: NMichael Pettersson <mike@it.uu.se>
Cc: <stable@kernel.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.

This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This essentially reverts commit 8edb08ca.

It downgraded our mmap semaphore to a read-lock while mlocking pages, in
order to allow other threads (and external accesses like "ps" et al) to
walk the vma lists and take page faults etc.  Which is a nice idea, but
the implementation does not work.

Because we cannot upgrade the lock back to a write lock without
releasing the mmap semaphore, the code had to release the lock entirely
and then re-take it as a writelock.  However, that meant that the caller
possibly lost the vma chain that it was following, since now another
thread could come in and mmap/munmap the range.

The code tried to work around that by just looking up the vma again and
erroring out if that happened, but quite frankly, that was just a buggy
hack that doesn't actually protect against anything (the other thread
could just have replaced the vma with another one instead of totally
unmapping it).

The only way to downgrade to a read map _reliably_ is to do it at the
end, which is likely the right thing to do: do all the 'vma' operations
with the write-lock held, then downgrade to a read after completing them
all, and then do the "populate the newly mlocked regions" while holding
just the read lock.  And then just drop the read-lock and return to user
space.

The (perhaps somewhat simpler) alternative is to just make all the
callers of mlock_vma_pages_range() know that the mmap lock got dropped,
and just re-grab the mmap semaphore if it needs to mlock more than one
vma region.

So we can do this "downgrade mmap sem while populating mlocked regions"
thing right, but the way it was done here was absolutely not correct.
Thus the revert, in the expectation that we will do it all correctly
some day.

Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Just like with the s5h1411, the s5h1409 needs a soft-reset in order for it
to know that the tuner has been told to change frequencies.  This change
changes the behavior from "random tuning times between 500ms to complete
tuning lock failures" to "tuning lock consistently within 700ms".

Thanks to Robert Krakora <rob.krakora@messagenetsystems.com> for doing
initial testing of the patch on the KWorld 330U.

Thanks to Andy Walls <awalls@radix.net> for doing testing of the patch on
the HVR-1600.

Thanks to Michael Krufky <mkrufky@linuxtv.org> for doing additional testing.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>