The current AT91 DT boards have a completely generic init_time definition.
Remove them from the machine declaration.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Conflicts:
	arch/arm/mach-at91/board-dt-sam9.c
	arch/arm/mach-at91/board-dt-sama5.c

The PIT timer driver until now had a single probe function, disregarding wether
it was probed through DT or in the old-style way. This code later on was
calling some DT function to retrieve the proper values for its base address,
interrupts and clocks.

While this was working, it was preventing the usage of CLOCKSOURCE_OF_DECLARE,
and the two different probe path were not as clearly separated as they could
be.

Rework the probe path to take this into account, and switch to
CLOCKSOURCE_OF_DECLARE.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove selection of OLD_IRQ_AT91 when selecting dt boards.
Select ATMEL_AIC_IRQ for sama5 SoCs (a kernel compiled for this SoC will
always use ATMEL_AIC_IRQ driver).
Select ATMEL_AIC_IRQ for at91rm9200 and at91sam9 SoCs only if OLD_IRQ_AT91
is not selected (which means we are compiling a pure DT kernel, without
any legacy board support).

Remove specific irq init code in all dt board files: this init procedure
is automatically handled in of_irq_init which is called by the arm irq core
code and is in charge of calling the appropriate aic init functions.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch prepare the transition to common clk for sam9 dt boards by
replacing the timer init callback.

Clocks registration cannot be done in early init callback (as formerly done
by the old clk implementation) because it requires dynamic allocation
which is not ready yet during early init.

In the other hand, at91 clocks must be registered before
at91sam926x_pit_init is called because PIT (Periodic Interval Timer) driver
request the master clk (mck).

A new function (at91sam9_dt_timer_init) is created to fullfil these needs.
This function registers all at91 clks using the dt definition before
calling the PIT init function.
The device tree clock registration is enabled only if common clk is
selected. Else the old clk registration is been done during
at91_dt_initialize call.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Since 883a106b (ARM: default
machine descriptor for multiplatform) we can remove the SoC-specific
callback init_machine() to use the default code.
This cleans up the code and reduces the number of lines.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

We will produce a board-dt file per SoC core type. That will ease code
readability and will prevent from including superfluous code for supporting
machines that will never be compiled together (particularly the ARM9 and C-A5
upcoming SoCs).
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: modify commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.

This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html

Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

as this is only used board old style board old mach code
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

as this is only used board old style board
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

This is also include the gpio controller as the IP share both.
Each soc will have to describe the SoC limitation and pin configuration via
DT.

This will allow to do not need to touch the C code when adding new SoC if the
IP version is supported.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

SOC_AT91SAM9 selects MULTI_IRQ_HANDLER in order to let machines specify their
own IRQ handler at run time.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This will allow to add any board to a compiled kernel by just passing the DTB.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This will allow to have static Device mapping and DT probe mapping for the
System Controller.

Temporary keep the call to ioremap_registers() until we have the binding
for the SDRAM/DDR Controller.

Temporary keep the main clock hardcoded to 12MHz until we have the binding
for the PMC.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Use a local copy of board informatin and fill with DT data.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable it on Calao board too as they are in DT too.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).

Set ecc mode in the boards to soft as currently in the driver.

Move platform data to a common header
include/linux/platform_data/atmel_nand.h
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)

Support for those new features are retrieved from the device tree
compatibility string.

Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Both AIC and GPIO controllers are now using the standard of_irq_init()
function to initialize IRQs in case of DT use.
The DT specific initialization functions are now separated from the
non-DT case and are now using "linear" irq domains.
The .map() irqdomain operation is responsible for positioning the IRQ
handlers. In AIC case, the Linux IRQ number is directly programmed in
the hardware to avoid an additional reverse mapping operation.
The AIC position its irq domain as the "default" irq domain.

For DT case, the priority is not yet filled in the SMR. It will be the
subject of another patch.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Adding of irqdomain in AIC code make the specification
of the irq domain in board file useless.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This default console mechanism is not used if the console is selected
by command line (console= parameter).
Dropping this will simplify the compilation of multiple SoC in the same
kernel image.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add at91sam9x5.c SoC file: Define clock resources
and some initialization code.
Signed-off-by: NDan Liang <dan.liang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

this will allow to use gpio_is_valid
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

now sam9_smc_configure will take as first parameter is the SMC id
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>

Create a new device tree source file for Atmel at91sam9g45 SoC family.
The Evaluation Kit at91sam9m10g45ek includes it.
This first basic support will be populated as drivers and boards will be
converted to device tree.
Contains serial, dma and interrupt controllers.

The generic board file still takes advantage of platform data for early serial
init. As we need a storage media and the NAND flash driver is not converted to
DT yet, we keep old initialization for it.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>