SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.

Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Convert to use of_match_node method to fix up eSDHC clock for
ls1046a/ls1012a/p1010. Also add eSDHC clock fixup for ls1021a
according to its datasheet. The maxmum speed for ls1021a eSDHC
high speed mode is 46.5MHz.
Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: Nyinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
Signed-off-by: Nyinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SD clock should be disabled for clock value 0. It's not
right to just return. This may cause failure of signal
voltage switching.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eSDHC is not a standard SD host controller. SDHCI_CAPABILITIES_1
register address is 0x44 while it's 0x114 (ESDHC_CAPABILITIES_1)
for eSDHC.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ls1046a datasheet specified that the max SD clock frequency
for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet
specified it's 125MHz for ls1012a. So this patch is to add the
limitation.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The loop to poll ESDHC_CLOCK_STABLE bit with mdelay would waste time
because the time to stabilize is much less than 1 ms. This patch is
to use udelay instead to avoid time wasting.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It's observed that eSDHC needed delay between tuning cycles for
HS200 successful tuning. This patch is to set 1ms delay for that.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eSDHC uses tuning block for tuning procedure. So the tuning
block control register must be configured properly before tuning.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eSDHC supports signal voltage switch from 3.3v to 1.8v by
eSDHC_PROCTL[VOLT_SEL] bit. This bit changes the value of output
signal SDHC_VS, and there must be a control circuit out of eSDHC
to change the signal voltage according to SDHC_VS output signal.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eSDHC could select peripheral clock or platform clock as clock source by
the PCS bit of eSDHC Control Register, and this bit couldn't be reset by
software reset for all. In default, the platform clock is used. But we have
to use peripheral clock since it has a higher frequency to support eMMC
HS200 mode and SD UHS-I mode. This patch is to add peripheral clock support
and use it instead of platform clock if it's declared in eSDHC dts node.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition.  Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLudovic Desroches <ludovic.desroches@microchip.com>

The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NScott Wood <oss@buserror.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since commit 87a18a6a ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
  mmc0: Card stuck in programming state! __mmc_switch
  mmc0: error -110 whilst initialising MMC card

Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.
Signed-off-by: NMichael Walle <michael@walle.cc>
Fixes: 87a18a6a ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use of_property_read_bool to check for the existence of a property.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
-       if (of_get_property(e1,e2,NULL))
+       if (of_property_read_bool(e1,e2))
        S1 else S2
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let's use the SIMPLE_DEV_PM_OPS macro when declaring/assigning the system
PM callbacks, as the code gets simplified.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit 0e748234 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-esdhc driver to this allocation.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
	u32 vvn;

	vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
	vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
	if (vvn == VENDOR_V_22)
		host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;

	if (vvn > VENDOR_V_22)
		host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}

This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For eSDHC(version < 2.3), the pre divider only could divide base clock
by 2 at least. Add workaround for this to avoid unexpected issue.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Acked-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fixes: bd455029 ("mmc: sdhci-of-esdhc: Pre divider starts at 1")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable interrupt mode to detect card instead of polling mode
for P1020/P4080/P5020/P5040/T1040 by removing the quirk
SDHCI_QUIRK_BROKEN_CARD_DETECTION. This could improve data
transferring performance and avoid the call trace caused by
polling card status sometime.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For PowerPC esdhc pre divider starts at 1, fixing the increases
the actual clock from 40KHz to 50 KHz.
Signed-off-by: NJoakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In these drivers, the driver specific .remove function just a simple
wrapper of function sdhci_pltfm_unregister(). So remove these wrappers
and just set .remove to sdhci_pltfm_unregister().
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit 0718e59a ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).

Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit below introduced compile errors, let's fix them.
mmc: sdhci-of-esdhc: remove platform_suspend/platform_resume callbacks

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

We don't need these hooks in order to insert code in these paths, we
can just provide our own handlers and call the main sdhci handlers as
appropriate.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method.  This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves.  This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios().  So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

This enables access the actual_clock via sys.
root@imx6qsabreauto:~# cat /sys/kernel/debug/mmc0/ios
clock:          198000000 Hz
actual clock:   198000000 Hz
vdd:            17 (2.9 ~ 3.0 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      2 (4 bits)
timing spec:    6 (sd uhs SDR104)
signal voltage: 0 (1.80 V)
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>