Handle up to 8 block layer requests per HW request. These requests
can be processed in parallel on the device leading to better
throughput (and less interrupts). The overhead for additional
requests is small since we don't blindly allocate new aidaws but
try to use what's left of the previous one.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

AOBs (the structure describing the HW request) need to be 4K
aligned but very little of that page is actually used. With
this patch we place aidaws at the end of the AOB page and only
allocate a separate page for aidaws when we have to (lists of
aidaws must not cross page boundaries).
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

We currently use one preallocated page per HW request to store
aidaws. With this patch we use mempool to allocate an aidaw page
whenever we need it.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Tests have shown that 5 seconds is sometimes not enough for an IRQ
to arrive (especially when the device is doing garbage collection).
Let's wait a little longer.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

In case somebody attempted to open the device during online
processing the partition detection ioctl may have failed.

Added a retry loop to avoid not detected partitions.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix race for sleep_on requests leading to list corruption.
The SLEEP_ON_END_TAG is set during CQR clean up. Remove it from
interrupt handler to avoid the CQR from being cleared when it is
still in the device_queue.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

During device activation all paths could be lost and since the device
is not active it has no indication of this fact - hence the CQR will
time-out. The following cancelation might fail with -EINVAL because
CIO took over control and started path verification. In this case mark
the CQR as being CLEARED since it could not be running any more.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Allow to specify the Compoment ID for Call Home via the kernel
configuration. This removes the need for distribution specific
patch against the sclp_async.c source file.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Using a VID value that is not high enough for the requested P state can
cause machine checks. Add a ceiling function to ensure calulated VIDs
with fractional values are set to the next highest integer VID value.

The algorythm for calculating the non-trubo VID from the BIOS writers
guide is:
 vid_ratio = (vid_max - vid_min) / (max_pstate - min_pstate)
 vid = ceiling(vid_min + (req_pstate - min_pstate) * vid_ratio)

Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

BYT has a different conversion from P state to frequency than the core
processors.  This causes the min/max and current frequency to be
misreported on some BYT SKUs. Tested on BYT N2820, Ivybridge and
Haswell processors.

Link: https://bugzilla.yoctoproject.org/show_bug.cgi?id=6663
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The user may have custom settings don't destroy them during suspend.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=80651Reported-by: NTobias Jakobi <liquid.acid@gmx.net>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Some BIOSes modify the state of MSR_IA32_MISC_ENABLE_TURBO_DISABLE
based on the current power source for the system battery AC vs
battery. Reflect the correct current state and ability to modify the
no_turbo sysfs file based on current state of
MSR_IA32_MISC_ENABLE_TURBO_DISABLE.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=83151
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently the core does not expose scaling_cur_freq for set_policy()
drivers this breaks some userspace monitoring tools.
Change the core to expose this file for all drivers and if the
set_policy() driver supports the get() callback use it to retrieve the
current frequency.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=73741
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Code which changes policy to powersave changes also max_policy_pct based on
max_freq. Code which change max_perf_pct has upper limit base on value
max_policy_pct. When policy is changing from powersave back to performance
then max_policy_pct is not changed. Which means that changing max_perf_pct is
not possible to high values if max_freq was too low in powersave policy.

Test case:

$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
800000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
100

$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 800000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 20 > /sys/devices/system/cpu/intel_pstate/max_perf_pct

$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
800000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
20

$ echo performance > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 3300000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 100 > /sys/devices/system/cpu/intel_pstate/max_perf_pct

$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
24

And now intel_pstate driver allows to set maximal value for max_perf_pct based
on max_policy_pct which is 24 for previous powersave max_freq 800000.

This patch will set default value for max_policy_pct when setting policy to
performance so it will allow to set also max value for max_perf_pct.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

If the irqchip handling the PCIe PME interrupt is not able
to enable interrupt wakeup we should properly reflect this
in the PME suspend status.

This fixes a kernel warning on resume, where it would try
to disable the irq wakeup that failed to be activated while
suspending, for example:

WARNING: CPU: 0 PID: 609 at kernel/irq/manage.c:536 irq_set_irq_wake+0xc0/0xf8()
Unbalanced IRQ 384 wake disable

Fixes: 76cde7e4 (PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle)
Reported-and-tested-by: NRichard Zhu <richard.zhu@freescale.com>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Fix a bug that invokes acpi_device_wakeup() with wrong parameters.

Fixes: f35cec25 (ACPI / PM: Always enable wakeup GPEs when enabling device wakeup)
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The MIPS_CPS_PM and MIPS_CPS_CPUIDLE implementation should depend
on the MIPS_CPS symbol to avoid the following build problem

arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
arch/mips/kernel/pm-cps.c:164:26: error: 'cpu_coherent_mask' undeclared
(first use in this function)
cpumask_clear_cpu(cpu, &cpu_coherent_mask);
                            ^
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7798/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

physdev_pci_device_add's optarr[] is a zero-sized array and therefore
reference to add.optarr[0] is accessing memory that does not belong to
the 'add' variable.
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Commit 3dcf6367 ("xen/balloon: cancel ballooning if adding new
memory failed") makes reserve_additional_memory() return BP_ECANCELED
when an error is encountered. This error, however, is ignored by the
caller (balloon_process()) since it is overwritten by subsequent call
to update_schedule(). This results in continuous attempts to add more
memory, all of which are likely to fail again.

We should stop trying to schedule next iteration of ballooning when
the current one has failed.
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NDaniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

qemu as used by xend/xm toolstack uses a different subvendor id.
Bind the drm driver also to this emulated card.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

In the case of at91sam9g45_restart(), the driver is writing
AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be
AT91_DDRSDRC_LPR.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Limit primary to qemu vgamem size, to avoid reaching
qemu guest bug "requested primary larger than framebuffer"
on resizing screen too large to fit.

Remove unneeded and misleading variables.

Related to:
https://bugzilla.redhat.com/show_bug.cgi?id=1127552Signed-off-by: NMarc-André Lureau <marcandre.lureau@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Most devices are configured for 32-bit DMA addresses.
Setting the mask to 32-bit here removes the need for the
drivers to do it separately.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We hard code the metrics relevant for cpuidle states in the kernel today.
Instead pick them up from the device tree so that they remain relevant
and updated for the system that the kernel is running on.
Signed-off-by: NPreeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The cpufreq-dt driver tries to get a regulator for each CPU. This
regulator is optional, but when not present, a scary message "failed
to get cpuX regulator" is displayed. To solve this, we reduce the
severity of the message from dev_warn() to dev_dbg() and we reword the
message to not be as scary.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This commit extends the cpufreq-dt driver to take a platform_data
structure. This structure is for now used to tell the cpufreq-dt
driver the layout of the clocks on the platform, i.e whether all CPUs
share the same clock or whether each CPU has a separate clock.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This commit extends the cpufreq_driver structure with an additional
'void *driver_data' field that can be filled by the ->probe() function
of a cpufreq driver to pass additional custom information to the
driver itself.

A new function called cpufreq_get_driver_data() is added to allow a
cpufreq driver to retrieve those driver data, since they are typically
needed from a cpufreq_policy->init() callback, which does not have
access to the cpufreq_driver structure. This function call is similar
to the existing cpufreq_get_current_driver() function call.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch cleans up the following coding style issues that are detected by
scripts/checkpatch.pl:
 ERROR: code indent should use tabs where possible
 ERROR: "foo * bar" should be "foo *bar"
 WARNING: Missing a blank line after declarations
 WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
 WARNING: void function return statements are not generally useful
 WARNING: else is not generally useful after a break or return
 WARNING: break is not useful after a goto or return
 WARNING: braces {} are not necessary for single statement blocks
 WARNING: line over 80 characters
 WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
No functional changes.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch refines event/query debugging messages to use a unified format
as commands. Developers can clearly find different processes by checking
different log seperators. No functional changes.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Developers really don't need to translate EC commands in mind. This patch
adds detailed debugging information for the EC commands.
The address can be found in the follow-up sequential EC_DATA(W) accesses,
thus this patch also removes some of the redundant address information.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently some logs are applied to new transactions, but QR_EC transactions
are not included. This patch merges the code path to make the logs also
applying to the QR_EC transactions.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch adds CPU ID to the context entries' debugging output. no
functional changes.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Adds support for both iASL and the disassembler to create a hardware
and connection summary mapfile (via the -lm option.)

Linux isn't affected by this patch because iASL is not in the Linux
upstream.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch is partial linuxized result of the following ACPICA commit:
  ACPICA commit: a73b66c6aa1846d055bb6390d9c9b9902f7d804d
  Subject: Add "has handler" flag to event/gpe status interfaces.
  This change adds a new flag, ACPI_EVENT_FLAGS_HAS_HANDLER to the
  acpi_get_event_status and acpi_get_gpe_status external interfaces. It
  is set if the event/gpe currently has a handler associated with it.
This patch contains the code to rename ACPI_EVENT_FLAG_HANDLE to
ACPI_EVENT_FLAG_HAS_HANDLER, and the corresponding updates of its usages.

Link: https://github.com/acpica/acpica/commit/a73b66c6Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch is a partial linuxized result of the following ACPICA commit:
  ACPICA commit: a73b66c6aa1846d055bb6390d9c9b9902f7d804d
  Subject: Add "has handler" flag to event/gpe status interfaces.
  This change adds a new flag, ACPI_EVENT_FLAGS_HAS_HANDLER to the
  acpi_get_event_status and acpi_get_gpe_status external interfaces. It
  is set if the event/gpe currently has a handler associated with it.
This commit back ports ACPI_EVENT_FLAG_HANDLE from Linux upstream to
ACPICA, the flag along with its support code currently can only be found
in the Linux upstream and is used by the ACPI sysfs GPE interfaces and
the ACPI bus scanning support.

Link: https://github.com/acpica/acpica/commit/a73b66c6Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The originally_enabled check is not paired between
acpi_install_gpe_handler() and acpi_remove_gpe_handler().

In ACPICA upstream, there is code to protect original enabled state for
ACPI_GPE_DISPATCH_NOTIFY and this commit fixes an issue for this feature.

Link: https://github.com/acpica/acpica/commit/967f314cSigned-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There is a sanity check in ACPICA upstream, complaining mis-matched
interrupt type for originally enabled GPEs that are going to be dispatched
by OSPM handlers. This is only a warning message noting developers such
conflict between BIOS and OSPM. This patch ports this warning message from
ACPICA upstream to reduce source code difference between Linux and ACPICA
upstream.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch reduces indent divergences first in order to reduce human
intervention work for the follow-up linuxized event patches.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The acpidump currently always uses ACPI 2.0 format to dump RSDP, this patch
adds ACPI 1.0 RSDP support.

Link: https://bugs.acpica.org/show_bug.cgi?id=1097
Link: https://bugs.acpica.org/show_bug.cgi?id=1103Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: NRudolf Marek <r.marek@assembler.cz>
Reported-and-tested-by: NRafal <fatwildcat@gmail.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>