Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updating the version
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.

If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again.  This would lead to occasional SMI access timeouts
when the system would be under heavy load.

The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

1. compile fix for irqreturn_t type change
2. restore ->poll_controller after CONFIG_PPC_CPM_NEW_BINDING transition
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This reverts 51ac3bef ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.

The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.

Based upon a build failure report from Manuel Lauss.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_kfree_skb should not be called with irqs disabled, use dev_kfree_skb_irq
instead. The warning caused looks like this:

======================================================
[ INFO: hard-safe -> hard-unsafe lock order detected ]
2.6.28-rc1 #273
------------------------------------------------------
swapper/0 [HC0[0]:SC1[2]:HE0:SE0] is trying to acquire:
 (clock-AF_INET){-..+}, at: [<4015c17c>] _sock_def_write_space+0x28/0xd8

and this task is already holding:
 (&lp->lock){++..}, at: [<4013f230>] _smc911x_hard_start_xmit+0x30/0x4b8
which would create a new lock dependency:
 (&lp->lock){++..} -> (clock-AF_INET){-..+}
Signed-off-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Saikiran Madugula, commit 7447ef63
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excess kernel-doc function parameters from networking header
& driver files:

Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move SKB trim before we lookup the socket so we don't have to
put it on failure.

Based upon an initial patch by Jarek Poplawski and suggestions
from Herbert Xu.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up.  Resetting
the link causes it to go down for several seconds.  This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode).  The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.

The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus.  This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.

The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.

Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device.  This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.

The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY.  This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers.  As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).

Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar.  But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.

We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers.  If one is found the ID of its platform device is saved in the
gianfar's platform data.

A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID.  The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Acoording commit aa24886e,
dma_free_coherent() need irqs enabled.

This patch fix following warning messages:

WARNING: at linux/arch/x86/kernel/pci-dma.c:376 dma_free_coherent+0xaa/0xb0()

Call Trace:
 [<ffffffff8023f80f>] warn_on_slowpath+0x5f/0x90
 [<ffffffff80496ffa>] ? __kfree_skb+0x3a/0xa0
 [<ffffffff802a4723>] ? discard_slab+0x23/0x40
 [<ffffffff8021274a>] dma_free_coherent+0xaa/0xb0
 [<ffffffff8043668f>] amd8111e_close+0x10f/0x1b0
 [<ffffffff8049f3ae>] dev_close+0x5e/0xb0
 [<ffffffff8049efa1>] dev_change_flags+0xa1/0x1e0
 [<ffffffff806b2171>] ic_close_devs+0x36/0x4e
 [<ffffffff806b29ee>] ip_auto_config+0x581/0x10f3
 [<ffffffff803a6e19>] ? kobject_add+0x69/0x90
 [<ffffffff803a698a>] ? kobject_get+0x1a/0x30
 [<ffffffff803a785b>] ? kobject_uevent+0xb/0x10
 [<ffffffff803a6c62>] ? kset_register+0x52/0x60
 [<ffffffff803a6f9b>] ? kset_create_and_add+0x6b/0xa0
 [<ffffffff804e2e74>] ? tcp_ca_find+0x24/0x50
 [<ffffffff806b246d>] ? ip_auto_config+0x0/0x10f3
 [<ffffffff8020903c>] _stext+0x3c/0x150
 [<ffffffff802772d3>] ? register_irq_proc+0xd3/0xf0
 [<ffffffff802f0000>] ? mb_cache_create+0x80/0x1f0
 [<ffffffff80688693>] kernel_init+0x141/0x1b8
 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8
 [<ffffffff8020d609>] child_rip+0xa/0x11
 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8
 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8
 [<ffffffff8020d5ff>] ? child_rip+0x0/0x11
Signed-off-by: NChunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 401c0aab introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.

This patch causes the VLAN tag to be stored in its proper location.
Tested-by: NRamon Casellas <ramon.casellas@cttc.es>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:

    bond_close()
        bond_alb_deinitialize()
            tlb_deinitialize()
		kfree(bond_info->tx_hashtbl)
                bond_info->tx_hashtbl = NULL

Unfortunately if there are still slaves in the bond, when removing the
module the following happens:

    bonding_exit()
        bond_free_all()
            bond_release_all()
                bond_alb_deinit_slave()
                    tlb_clear_slave()
                        tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
			u32 next_index = tx_hash_table[index].next

As you might guess we panic when trying to access a few entries into the
table that no longer exists.

I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine.  It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch reworks the resource free logic performed at the time
a bonding device is released.  This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.

"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

During the rework of the mii monitor for:

  commit f0c76d61
  Author: Jay Vosburgh <fubar@us.ibm.com>
  Date:   Wed Jul 2 18:21:58 2008 -0700

    bonding: refactor mii monitor

I left out the increment of the link failure counter.  This
patch corrects that omission.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We were setting RX_FILTER_BEACON even after entering STA mode,
which leads to a lot of unnecessary wakeups.  This should fix the
bug "Ath5k driver has too many interrupts per second at idle" at
http://bugzilla.kernel.org/show_bug.cgi?id=11749.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Take care to handle register 0xa228 exactly as in the HAL released by
Atheros. This change is required to make ath5k work again on my system
since commit 2203d6be (ath5k: Misc hw_reset updates), thus fixing a
regression in 2.6.27 and therefore hopefully eligible for inclusion into
a stable release.

v2: Only overwrite initial register values on later revisions of AR5212
    chips.
v3: Use standard macros to manipulate the register.
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make menuconfig RT2X00 a tristate instead of boolean,
otherwise we do not correctly inherit the mac80211 value
on which RT2X00 depends, and makes it possible to
compile rt2x00 into the kernel while mac80211 is a
module.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change "mamagement" to "management"
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If somebody sends an invalid beacon/probe response, that can trash the
whole BSS descriptor. The descriptor is, luckily, large enough so that
it cannot scribble past the end of it; it's well above 400 bytes long.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.24-2.6.27, bug present in some form since driver was added (2.6.22)]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes Berg detected this two sparse warnings:

drivers/net/wireless/libertas/cmd.c:609:16: warning: cast to restricted __le16
drivers/net/wireless/libertas/cmd.c:611:16: warning: cast to restricted __le16

... but cmd.minlevel is "s8", so we can access it directly and hope
for the sign-extension-code in the compiler to convert that to the
"s16" type.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes suspend to RAM after by moving
notify_mac out of iwlwifi mutex

http://bugzilla.kernel.org/show_bug.cgi?id=11845Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NCarlos R. Mafra <crmafra2@gmail.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The amd8111e rx poll routine currently mishandles the case when we
process exactly the number of packets specified in the budget.

This patch is basically as suggested by David Miller.
Signed-off-by: NChris Friesen <cfriesen@nortel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Saturday 25 October 2008 10:24:10 Johannes Berg wrote:
> just FYI in case you haven't seen them. the p54 one looks like a genuine
> problem.
>
> drivers/net/wireless/p54/p54common.c: In function ‘p54_parse_eeprom’:
> drivers/net/wireless/p54/p54common.c:325: warning: ‘synth’ may be used uninitialized in this function

There you go. Yes, it is a genuine problem, if the device's eeprom is screwed really up.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After a s2ram / resume cycle, resetting the key cache does not work
unless it is deferred until after the hardware has been reinitialised by
a call to ath5k_hw_reset(). This fixes a regression introduced by
"ath5k: fix suspend-related oops on rmmod".
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a double-free error in p54pci
( http://bugzilla.kernel.org/show_bug.cgi?id=11782 )

Trying to free already-free IRQ 10
Pid: 108, comm: pccardd Not tainted 2.6.27-05577-g0cfd8103-dirty #1
Call Trace:
 [<c01265dc>] free_irq+0xad/0xb9
 [<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
 [<c01ba8e6>] p54p_stop+0x4a/0x1fa
 [<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
 [<c02348c5>] p54p_probe+0x23e/0x302

Tested-by: Sean Young
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement set_mac_address for runtime mac address change.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch corrects a message bug in the via-velocity driver which
bothered me for some time.

The messages printed during device init look like the following:

[    8.486422] eth%d: set value of parameter Wake On Lan options to 0
                  ^^!
[    8.487340] eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter

Note the unresolved format string.

dev->name is unavailable before register_netdev, so use
dev_driver_string(&pdev->dev), which is also consistent with other
drivers.

"char *devname" parameters had to be converted to "const char *devname" to
be consistent with dev_driver_string return value.
Signed-off-by: NSven Hartge <sven@svenhartge.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix !CONFIG_INET warnings.

Spotted, and original patch authored by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Removed duplicated #include <linux/cpumask.h> in
drivers/net/mlx4/en_main.c.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>