The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats2.
It adds also trats2 specific properties for DSI
and regulator required by panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats.
It adds also trats specific properties for DSI.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This is a common part of DSI node for all Exynos4 boards.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch replaces panel bindings for panel initialized by boot loader
with bindings to proper ld9040 panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds fimd node with display timings for exynos4210-universal device.
It also makes LCD regulators always on. This allow to re-use panel initialized
by boot loader.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Without that change booting leads to crash with more warnings like below:
[    0.284454] omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
[    0.284484] omap_hwmod: uart4: cannot _init_clocks
[    0.284484] ------------[ cut here ]------------
[    0.284545] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2543 _init+0x300/0x3e4()
[    0.284545] omap_hwmod: uart4: couldn't init clocks
[    0.284576] Modules linked in:
[    0.284606] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-next-20140124-00020-gd2aefec-dirty #26
[    0.284637] [<c00151c0>] (unwind_backtrace) from [<c0011e20>] (show_stack+0x10/0x14)
[    0.284667] [<c0011e20>] (show_stack) from [<c0568544>] (dump_stack+0x7c/0x94)
[    0.284729] [<c0568544>] (dump_stack) from [<c003ff94>] (warn_slowpath_common+0x6c/0x90)
[    0.284729] [<c003ff94>] (warn_slowpath_common) from [<c003ffe8>] (warn_slowpath_fmt+0x30/0x40)
[    0.284759] [<c003ffe8>] (warn_slowpath_fmt) from [<c07d1be8>] (_init+0x300/0x3e4)
[    0.284790] [<c07d1be8>] (_init) from [<c07d217c>] (__omap_hwmod_setup_all+0x40/0x8c)
[    0.284820] [<c07d217c>] (__omap_hwmod_setup_all) from [<c0008918>] (do_one_initcall+0xe8/0x14c)
[    0.284851] [<c0008918>] (do_one_initcall) from [<c07c5c18>] (kernel_init_freeable+0x104/0x1c8)
[    0.284881] [<c07c5c18>] (kernel_init_freeable) from [<c0563524>] (kernel_init+0x8/0x118)
[    0.284912] [<c0563524>] (kernel_init) from [<c000e368>] (ret_from_fork+0x14/0x2c)
[    0.285064] ---[ end trace 63de210ad43b627d ]---

Reference:
https://lkml.org/lkml/2013/10/8/553Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch is based on commit:

016c12d2 ("ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree")

and fixes a boot hang due the IGEP board being wrongly initialized
as an OMAP3430 platform instead of an OMAP3630.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This commit updates bcm11351.dtsi with the new compatible string for
the same driver.
Signed-off-by: NSherman Yin <syin@broadcom.com>
Reviewed-by: NMatt Porter <mporter@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChristian Daudt <bcm@fixthebug.org>

The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.

Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.

Fixes: 553c0a20 ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The corresponding driver didn't make it into v3.14, so we need to remove
the node.  Dove systems fail to boot with the node present and no
driver.

This node will be re-added when the driver makes it to mainline.
Reported-by: NJean-Francois Moine <moinejf@free.fr>
Tested-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This reverts commit 01ab1167, it is
incorrect, a future patch will fix this up properly.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Unfortunatly the device tree for older OMAP35xx Overo cannot be used
with newer OMAP36xx and vice-versa. To address this issue, move most of
the Tobi DTS to a common include file, and create model-specific Tobi
DTS.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gumstix is the correct vendor for all Overo related products.
Reported-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Tobi expansion board can be used with both OMAP35xx-based Overo,
and OMAP36xx-based Overo. Currently the boot is broken with newer
OMAP36xx-based Overo (Storm and alike). Fix include file and
compatible string to be able to boot newer models.

This will break older models. This will be addressed later.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing compatible property to avoid problems in the future.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

N9/N950 does not boot anymore with 3.14-rc1, because SoC compatible
property is missing. Fix that.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Does not have an aux supply, and must be non-removable.

Otherwise it is removed during suspend and filesystem gets confused.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It should be ACTIVE_HIGH.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not
working on EVM-SK board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

BMP085 EOC (End Of Conversion) irq line is connected to
gpio113 on gta04. Set irq properties to have driver using irq
instead polling for EOC.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 70b41abc
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.

Fix this up by marking the node disabled again.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The address for control regs in clkvcp3 node is not correct and should
be 0x023500a8 instead of 0x0235000a8.

This lead to few unexpected behaviors while clocks were turned
of in absence of clk_ignore_unused

Mike Turquette <mturquette@linaro.org>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The spdif pinmux configuration must be connected to the spdif device to
take effect, not the spdif-transmitter.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Switch the device tree to the new compatibles introduced in the SID drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Switch the device tree touchscreen compatibles to have a common pattern accross
all Allwinner SoCs. Since the touchscreen driver has not been merged yet, it
has no side effect.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.

Fix this for the remaining DT nodes that slipped through.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org

Add DT file for new SAMA5D3 Xplained board.
This board is based on Atmel's SAMA5D36 Cortex-A5 SoC.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable USB host on at91sam9n12ek board.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The hclk clock of the ohci node is referencing udphs_clk instead of
uhphs_clk.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Switch the device tree to the new compatibles introduced in the ethernet and
mdio drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was correctly set on mv78460 but not on mv78260, resulting in my
OpenBlocks AX3-4 retrieving only 3 of its 4 MAC addresses from the
boot loader.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.

Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.

Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>