commit 10c994ca70e8e94bbc85a5bf13de5911ee8de4d2 "iwlwifi: fix remove key
error" fixed an error reported by mac80211 during interface down. The fix
involved changing an async command to synchronous. Unfortunately this was
inside a spinlock section in which we cannot sleep.

Modify the sending of the command back to async. This causes the mac80211
error "mac80211-phy0: failed to remove key (0, ff:ff:ff:ff:ff:ff) from
hardware (-16)." to return. This error is not serious since this occurs
during interface down and the keys will be cleared anyway when ucode is
unloaded. Having this error message is thus less serious than a potential
deadlock introduced when sleeping while holding a spinlock. We will have to
find another fix for that error.

This is a revert of the abovementioned commit.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the DTIM setting is read from beacons, mac80211 will
assume it is 1 if the TIM IE is not present or the value
is 0. This sounds fine, but the same function processes
probe responses as well, which don't have a TIM IE. This
leads to overwriting any values previously parsed out of
beacon frames.

Thus, instead of checking for the presence of the TIM IE
when setting the default, simply check whether the DTIM
period value is valid already. If the TIM IE is not there
then the value cannot be valid (it is initialised to 0)
and probe responses received after beacons will not lead
to overwriting an already valid value.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the usbid for TP-Link TL-WN821N v2.

Cc: stable@kernel.org
Reported-by: NFabian Lenz <lenz_fabian@yahoo.de>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Autosleep needs to be disabled for AR9287 chipsets also.
Since autosleep is not used for any of the currently supported
chipsets, disable it by default and can be enabled if needed
for any of the future chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Fix bugs in programming registers during PA CAL"
removed a REG_READ of 0x7834. This resulted in incorrect
computation of the subsequent value to be written in RF2G6.

This patch fixes the regression by re-adding the REG_READ.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* This patch fixes a bug in calculating the scaled
  power for three chain chipsets.

* Also, a delay is needed after setting DAC low-power mode in
  TOP1 RF register (Top Level Register Bits).
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Do an AHB reset before doing RTC reset"
fixed RTC reset issue for AR9280 2.0 chipsets and above.
The fix is valid for all AR9280 chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is needed to account for the number of chains in use,
not just the number of chains present.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9280 requires a full reset during channel change and HW reset.
Currently, a fast channel change is done. This patch fixes
this bug.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

NF value may be incorrect when we read it just after the chip
has gone through a full sleep mode. Reading incorrect NF values
affects RX throughput.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting bit 20 and 25 of 0x8344 can cause occasional rx data
corruption, clear them to fix this issue.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Waking up the chip after powering it down fails sometimes.
In this case the CPU is locked for 200ms. Reduce this
interval to 10ms to avoid excessive busy looping.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly

Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LP (and probably N) PHY has the same radio disabled bit as
the higher-revision A and G PHYs.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO works (more or less), so remove the BROKEN dependency and
let people test it.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following build error when CONFIG_B43_LEDS is not selected:

drivers/net/wireless/b43/main.c: In function 'b43_remove':
drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop'
drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work'
make[4]: *** [drivers/net/wireless/b43/main.o] Error 1
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't abuse wl->current_dev in the LED work for checking whether we're
going down. Add an explicit variable.
This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer
in various other places of the driver.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current verison of b43 uses "b43_phyop_switch_analog_generic" for A,
G and LP phys.

According to the spec, this is the wrong behaviour for the LP PHY
(see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )

While no problems on the x86 plattform where seen, this leads to a crash
on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the
specs. It fixes the crash
signed-off-by: NThomas Ilnseher <illth@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduces IRQ pressure by about one third on a saturated link
by disabling the PMQ mechanism. We currently don't use that mechanism.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for verbose runtime statistics.
It defaults to off and must be enabled in debugfs, if desired.
The first measurement may be incorrect, because statistics are not cleared
after they got enabled through debugfs.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

synchronize_irq is meaningless for SDIO. sdio_release_irq will
sync the IRQ thread for us.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to release the SDIO host before locking the driver mutex.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need to call the irqsafe callbacks.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for Soft-MAC SDIO devices to b43.
The driver still lacks some fixes for SDIO devices, so it's currently
marked as BROKEN.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes most of the b43 suspend/resume code (it's handled by mac80211)
and moves the registration of devices to the attachment phase. This is
required, because we must not register/unregister devices on suspend/resume.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a check saying
	/* we're good if we have both BSSID and channel */
	if (wdev->conn->params.bssid && wdev->conn->params.channel) {

but that isn't true -- we need the BSS struct. This leads
to errors such as

    Trying to associate with 00:1b:53:11:dc:40 (SSID='TEST' freq=2412 MHz)
    ioctl[SIOCSIWFREQ]: No such file or directory
    ioctl[SIOCSIWESSID]: No such file or directory
    Association request to the driver failed
    Associated with 00:1b:53:11:dc:40

in wpa_supplicant, as reported by Holger.

Instead, we really need to have the BSS struct, and if we
don't, then we need to initiate a scan for it. But we may
already have the BSS struct here, so hang on to it if we
do and scan if we don't.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The contention window is supposed to be a power of two minus one, i.e.
15, 31, 63, 127...  minstrel_rate_init() forgets to subtract 1, so the
sequence becomes 15, 32, 66, 134...

Bug reported by Dan Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix printk format warnings:

drivers/ssb/sdio.c:336: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
drivers/ssb/sdio.c:443: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a new usbid for Zcomax XG-705A to the device table.

Cc: stable@kernel.org
Reported-by: NJari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an SPROM revision is not recognized, the code falls back to a V1
SPROM; however, that revision is not forced in the appropriate structure.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.

Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.

Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: NRick Farrington <rickdic@hotmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disable SDIO coreswitch debugging.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>