WCN3990 uses larger ring size in comparison to existing
ring size value.
Add rx ring size hw param for supporting different rx ring
size across multiple target.
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WCN3990 target uses 64 bit frags_paddr in htt tx descriptor,
which holds the physical address of SKB fragments in tx data path.

In order to support 64 bit bit frags_paddr in htt tx descriptor, define
htt_data_tx_desc_64 descriptor and ath10k_htt_tx_64 method for handling
tx data path with new descriptor fields.
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WCN3990 target uses 64 bit frag descriptor and more
fields in TSO flag.
Add support for 64 bit HTT frag descriptor.
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WCN3900 target uses 64bit rx_ring_base_paddr and
fw_idx_shadow_reg_paddr fields in HTT rx ring cfg message.
These address points to the memory region where remote
ring empty buffers are allocated.
In order to add 64 bit htt rx ring cfg, define separate
64 bit htt rx ring cfg message and attach it in runtime
based on target_64bit hw param flag.
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WCN3990 target use 64bit msdu address in htt in-order
indication message. Add support for 64 bit msdu address in
HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND message.
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.2.4 firmware branch (used in QCA988X) does not support
HTT_10_4_T2H_MSG_TYPE_PEER_STATS and that's why ath10k does not provide
tranmission rate statistics to user space, instead it just shows
hardcoded 6 Mbit/s. But pktlog firmware facility provides per peer tx
statistics. The firmware sends one pktlog event for every four
PPDUs per peer, which include:

* successful number of packets and bytes transmitted
* number of packets and bytes dropped
* retried number of packets and bytes
* rate info per ppdu

Firmware supports WMI_SERVICE_PEER_STATS, pktlog is enabled through
ATH10K_FLAG_PEER_STATS, which is nowadays enabled by default in ath10k.

This patch does not impact throughput.

Tested on QCA9880 with firmware version 10.2.4.70.48. This should also
work with firmware branch 10.2.4-1.0-00029

Parse peer stats from pktlog packets and update the tx rate information
per STA. This way user space can query about transmit rate with iw:

$iw wlan0 station dump
Station 3c:a9:f4:72:bb:a4 (on wlan1)
        inactive time:  8210 ms
        rx bytes:       9166
        rx packets:     44
        tx bytes:       1105
        tx packets:     9
        tx retries:     0
        tx failed:      1
        rx drop misc:   3
        signal:         -75 [-75, -87, -88] dBm
        signal avg:     -75 [-75, -85, -88] dBm
        tx bitrate:     39.0 MBit/s MCS 10
        rx bitrate:     26.0 MBit/s MCS 3
        rx duration:    23250 us
        authorized:     yes
        authenticated:  yes
        associated:     yes
        preamble:       short
        WMM/WME:        yes
        MFP:            no
        TDLS peer:      no
        DTIM period:    2
        beacon interval:100
        short preamble: yes
        short slot time:yes
        connected time: 22 seconds
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

With current NAPI implementation, NAPI poll can deliver more frames
to net core than allotted budget. This may cause warning in napi_poll.
Remaining quota is not accounted, while processing amsdus in
rx_in_ord_ind and rx_ind queue. Adding num_msdus at last can not
prevent delivering more frames to net core. With this change,
all amdus from both in_ord_ind and rx_ind queues are processed and
enqueued into common skb list instead of delivering into mac80211.
Later msdus from common queue are dequeued and delivered depends on
quota availability. This change also simplifies the rx processing in
napi poll routine.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix output from checkpatch.pl like:

 Block comments use a trailing */ on a separate line
Signed-off-by: NMarcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes new checkpatch warnings:

drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes new checkpatch warnings:

drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'

a) memory footprint of ath10k without the change

lsmod | grep ath10k
ath10k_core           414498  1 ath10k_pci
ath10k_pci             38236  0

b) memory footprint of ath10k with the change

ath10k_core           414980  1 ath10k_pci
ath10k_pci             38236  0

Memory Failure Call trace:

hostapd: page allocation failure: order:6, mode:0xd0
 [<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS'
event, Firmware sends one HTT event for every four PPDUs.
HTT payload has success pkts/bytes, failed pkts/bytes, retry
pkts/bytes and rate info per ppdu.
Peer stats are enabled through 'WMI_SERVICE_PEER_STATS',
which are nowadays enabled by default.

Parse peer stats and update the tx rate information per STA.

tx rate, Peer stats are tested on QCA4019 with Firmware version
10.4-3.2.1-00028.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: NJoe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below

 - on interrupt
     - schedule napi and mask interrupts
 - on poll
   - process all pipes (no actual Tx/Rx)
   - process Rx within budget
   - if quota exceeds budget reschedule napi poll by returning budget
   - process Tx completions and update budget if necessary
   - process Tx fetch indications (pull-push)
   - push any other pending Tx (if possible)
   - before resched or napi completion replenish htt rx ring buffer
   - if work done < budget, complete napi poll and unmask interrupts

This change also get rid of two tasklets (intr_tq and txrx_compl_task).

Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.

DL: AP DUT Tx
UL: AP DUT Rx

IPQ4019 (avg. cpu usage %)

========
                TOT              +NAPI
              ===========      =============
TCP DL       644 Mbps (42%)    645 Mbps (36%)
TCP UL       673 Mbps (30%)    675 Mbps (26%)
UDP DL       682 Mbps (49%)    680 Mbps (49%)
UDP UL       720 Mbps (28%)    717 Mbps (11%)
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Only five bits are defined to pass tid information in HTT_RX_IND
message, so the mask which can be used to extract tid should be 0x1f
instead of the current 0x3f. Also, macros which can be used to extract
flush_valid and release_valid bits have to be left shifted one bit less
because these information follow the tid right after. This patch does
not really fix anything functionally because these macros are not used
currently.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/htt.h:1477: Prefer kernel type 'u64' over 'u_int64_t'
drivers/net/wireless/ath/ath10k/htt.h:1480: Prefer kernel type 'u64' over 'u_int64_t'
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since tx completion and rx indication processing are moved out
of txrx tasklet and rx ring lock contention also removed from txrx
for rx_ind messages, it would be efficient to combine both replenish
and txrx tasks. Refill threshold is adjusted for both AP135 and AP148
(low and high end systems). With this adjustment in AP135, TCP DL is
improved from 603 Mbps to 620 Mbps and UDP DL is improved from 758 Mbps
to 803 Mbps. Also no watchdog are observed on UDP BiDi.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Except qca61x4 family chips (qca6164, qca6174), copy engine 5 is used
for receiving target to host htt messages. In follow up patch, CE5
descriptors will be reused. In such case, same API can not be used as
htc layer callback where the response messages will be freed at the end.
Hence register new API for HTC layer that free up received message and
keep the message handler common for both HTC and HIF layers.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In follow up patch, htt rx descriptors will be reused instead of
dealloc and refill. To achieve that htt rx indication messages
should not be deferred and should be processed in pci tasklet itself.
Also from rx indication message, mpdu_count alone is used. So it is
maintained as atomic variable and all rx amsdu handlers are done
processed from txrx tasklet. This change get rid of rx_compl_q usage.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To optimize CPU usage htt rx descriptors will be reused instead of
refilling it for htt rx copy engine (CE5). To support that all htt rx
indications should be processed at same context. FIFO queue is used
to maintain tx completion status for each msdu. This helps to retain
the order of tx completion.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Frames that are transmitted via MGMT_TX are using reserved descriptor
slots in firmware. This limitation is for the htt_mgmt_tx path itself,
not for mgmt frames per se. In 16 MBSSID scenario, these reserved slots
will be easy exhausted due to frequent probe responses. So for 10.4
based solutions, probe responses are limited by a threshold (24).

management tx path is separate for all except tlv based solutions. Since
tlv solutions (qca6174 & qca9377) do not support 16 AP interfaces, it is
safe to move management descriptor limitation check under mgmt_tx
function. Though CPU improvement is negligible, unlikely conditions or
never hit conditions in hot path can be avoided on data transmission.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Whenever firmware is configuring operating channel during scan or
home channel, channel change event will be indicated to host. In some
cases (device probe/ last vdev down), target will be configured to
default channel whereas host is unaware of target's operating channel.
This leads to packet drop due to unknown channel and kernel log will be
filled up with "no channel configured; ignoring frame(s)!". Fix that
by handling HTT_T2H_MSG_TYPE_CHAN_CHANGE event.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The current/old tx path design was that host, at
its own leisure, pushed tx frames to the device.
For HTT there was ~1000-1400 msdu queue depth.

After reaching that limit the driver would request
mac80211 to stop queues. There was little control
over what packets got in there as far as
DA/RA was considered so it was rather easy to
starve per-station traffic flows.

With MU-MIMO this became a significant problem
because the queue depth was insufficient to buffer
frames from multiple clients (which could have
different signal quality and capabilities) in an
efficient fashion.

Hence the new tx path in 10.4 was introduced: a
pull-push mode.

Firmware and host can share tx queue state via
DMA. The state is logically a 2 dimensional array
addressed via peer_id+tid pair. Each entry is a
counter (either number of bytes or packets. Host
keeps it updated and firmware uses it for
scheduling Tx pull requests to host.

This allows MU-MIMO to become a lot more effective
with 10+ clients.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware 10.4.3 onwards can support a pull-push Tx
model where it shares a Tx queue state with the
host.

The host updates the DMA region it pointed to
during HTT setup whenever number of software
queued from (on host) changes. Based on this
information firmware issues fetch requests to the
host telling the host how many frames from a list
of given stations/tids should be submitted to the
firmware.

The code won't be called because not all
appropriate HTT events are processed yet.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This merely adds some parsing, generation and
sanity checks with placeholders for real
code/functionality to be added later.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Tx pending counter logic assumed that the sk_buff
is already known and hence was performed in HTT
functions themselves.

However, for the sake of future wake_tx_queue()
usage the driver must be able to tell whether it
can submit more frames to firmware before it
dequeues frame from ieee80211_txq (and thus long
before HTT Tx functions are called) because once a
frame is dequeued it cannot be requeud back to
mac80211.

This prepares the driver for future changes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.

This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New names make a bit more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct because
it can be passed as function argument down the tx
path.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Of a word in struct htt_data_tx_desc htt version >= 3.4 firmware uses
LSB 16-bit for frequency configuration which is used for offchannel tx
and MSB 16-bit is for peerid. But other firmwares using version 2.X
(10.1, 10.2.2, 10.2.4 and 10.4) are using 32-bit for peerid in htt tx
desc. So far no issue is found with the existing code setting peerid and
freq for HTT version 2.X, this could be mainly because of 0 as frequecy
(home channel) is being always passed with those firmwares. There may be
issues when non-zero freq is passed with firmware using < 3.4 htt version.
To be safe use target_version_major and target_version_minor along with
htt-op-version before configuring peer id and freq in htt tx desc. This
patch extends ath10k_mac_tx_frm_has_freq() to check for htt_op_version_tlv
and uses the helper while setting peerid in htt_tx_desc.

Fixes: 8d6d3624 ("ath10k: fix offchan reliability")
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch adds pktlog support for 10.4 fw versions.
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some special copy engines delivers messages directly to HTT by
bypassing HTC layer. Hence exporting tx_completion and rx_handler
for delivering the data to HTT layer.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k driver is using dma_pool_alloc per packet and dma_pool_free
in coresponding at Tx completion.
Use of pre-allocated DMA buffer in Tx will improve saving CPU resource
by 5% while it consumes about 56KB memory more as trade off.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In a noisy environment, when multiple interfaces are created,
the management tx descriptors are fully occupied by the probe
responses from all the interfaces. This prevents a new station
from a successful association.

Fix this by limiting the probe responses when the specified
threshold limit is reached.
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.

 cryptmode:

   0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
      encapsulation to the firmware. This is the default mode.
   1: Use sofware crypto engine globally with raw mode TX/RX
      encapsulation to the firmware.

Known limitation:
   A-MSDU must be disabled for RAW Tx encap mode to perform well when
   heavy traffic is applied.

Testing: (by Michal Kazior <michal.kazior@tieto.com>)

     a) Performance Testing

      cryptmode=1
       ap=qca988x sta=killer1525
        killer1525  ->  qca988x     194.496 mbps [tcp1 ip4]
        killer1525  ->  qca988x     238.309 mbps [tcp5 ip4]
        killer1525  ->  qca988x     266.958 mbps [udp1 ip4]
        killer1525  ->  qca988x     477.468 mbps [udp5 ip4]
        qca988x     ->  killer1525  301.378 mbps [tcp1 ip4]
        qca988x     ->  killer1525  297.949 mbps [tcp5 ip4]
        qca988x     ->  killer1525  331.351 mbps [udp1 ip4]
        qca988x     ->  killer1525  371.528 mbps [udp5 ip4]
       ap=killer1525 sta=qca988x
        qca988x     ->  killer1525  331.447 mbps [tcp1 ip4]
        qca988x     ->  killer1525  328.783 mbps [tcp5 ip4]
        qca988x     ->  killer1525  375.309 mbps [udp1 ip4]
        qca988x     ->  killer1525  403.379 mbps [udp5 ip4]
        killer1525  ->  qca988x     203.689 mbps [tcp1 ip4]
        killer1525  ->  qca988x     222.339 mbps [tcp5 ip4]
        killer1525  ->  qca988x     264.199 mbps [udp1 ip4]
        killer1525  ->  qca988x     479.371 mbps [udp5 ip4]

      Note:
       - only open network tested for RAW vs nwifi performance comparison
       - killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
       - used iperf
       - OTA, devices a few cm apart from each other, no shielding
       - tcpX/udpX, X - means number of threads used

      Overview:
       - relative Tx performance drop is seen but is within reasonable and
         expected threshold (A-MSDU must be disabled with RAW Tx)

     b) Connectivity Testing

      cryptmode=1
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan  OK

      Note:
       - each test takes all possible endpoint pairs and pings
       - each pair-ping flushes arp table
       - ip6 is used

     c) Testbed Topology:

      1ap1sta:
        [ap] ---- [sta]

        endpoints: ap, sta

      1ap1sta2br:
        [veth0] [ap] ---- [sta] [veth2]
           |     |          |     |
        [veth1]  |          \   [veth3]
            \   /            \  /
            [br0]            [br1]

        endpoints: veth0, veth2, br0, br1
        note: STA works in 4addr mode, AP has wds_sta=1

      1ap1sta2br1vlan:
        [veth0] [ap] ---- [sta] [veth2]
           |     |          |     |
        [veth1]  |          \   [veth3]
            \   /            \  /
          [br0]              [br1]
            |                  |
          [vlan0_id2]        [vlan1_id2]

        endpoints: vlan0_id2, vlan1_id2
        note: STA works in 4addr mode, AP has wds_sta=1

Credits:

    Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
    amsdu issue, contributed a workaround (already squashed into this
    patch), and contributed the throughput and connectivity tests results.
Signed-off-by: NDavid Liu <cfliu.tw@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Tested-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT_H2T_MSG_TYPE_MGMT_TX msg in 10.4 firmware carries additional
4 byte in htt_mgmt_tx_desc where it tells to firmware that at what
rate mgmt frame has to go out in the air. It's an optional parameter,
setting this field to zero will force firmware to choose auto rate
and send the frame out.

Those 4 byte info is missed out in the current code and 10.4 firmware
ended up reading some junk in those 4 byte and sometime malfunctioning.

Fix it by adding 4 byte in struct htt_mgmt_tx_desc. Non 10.4 firmware
will not process those four byte. So, adding 4 byte at the end of
struct htt_mgmt_tx_desc will not create any impact on other chipset.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The patch adds support to offload TCP/UDP checksum
calculations for QCA99x0.
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since QCA99X0 uses fragmentation descriptor differently from
other ones on tx path, we need to handle it separately.

QCA99X0 is using 48 bits for address and 16 bits for length
out of 2 dword and each values have to be programmed by frag
desc base addr + msdu id, so that hardware can retrieve
corresponding frag data.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>