This patch adds support for the Xilinx Ethernet Lite device.  The
soft logic core from Xilinx is typically used on Virtex and Spartan
designs attached to either a PowerPC or a Microblaze processor.
Signed-off-by: NSadanand M <sadanan@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The s6000 on-chip MAC supports 10/100/1000Mbit and is connected to an
external PHY via MII or RGMII interface.

[jw@emlix.com: don't use device->bus_id directly]
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NDaniel Glockner <dg@emlix.com>
Acked-by: N"David S. Miller" <davem@davemloft.net>
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NChris Zankel <chris@zankel.net>

The CNIC driver controls BNX2 hardware rings and resources used by
iSCSI.  Most hardware resources for iSCSI are separate from those
used for ethernet networking.

iSCSI uses a separate MAC address and IP address.  The CNIC driver
creates a UIO interface to handle the non-offloaded packets such as
ARP, etc in userspace.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This is a driver for the Micrel KS8842 ethernet switch.

The supplied code is for driving the KS8842 through the Timberdale FPGA
on the Russellville board, a development board for Intel Atom CPU
in the automotive area.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changeset ca17584b ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.

Tested with a Kinetics EtherPort card.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for TI DaVinci EMAC driver.

TI DaVinci Ethernet Media Access Controller module is based upon
TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on
some TI devices. It supports MII/RMII and has up to 8Kbytes of internal
descriptor memory. This driver has been working on several TI devices including
DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24aSigned-off-by: NAnant Gole <anantgole@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet
device.  The ll_temac ipcore is typically used on Xilinx Virtex and
Spartan designs attached to either a PowerPC 4xx or Microblaze
processor.

At the present moment, this driver only works with Virtex5 PowerPC
designs because it assumes DCR is used to access the DMA registers.
However, the low level access to DMA registers is abstracted and
it should be easy to adapt for the other implementations.

I'm posting this driver now as an RFC.  There are still some things that
need to be tightened up, but it does appear to be stable.

Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr.

Tested on Xilinx ML507 eval board with Base System Builder generated
FPGA design.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled.  A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.

To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS.  The virtual functions will appear after the
interface is loaded.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Kconfig and Makefile related changes for vxge driver.

- No changes in current submission.

- Changes from previous submission -
 - Incorporated the following review comments as per Bill Flink:
        - Add dependancy on INET along with PCI
        - Remove dependancy on INET_LRO and add GRO support.
 - Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a platform device driver that supports the OpenCores 10/100
Mbps Ethernet MAC.

The driver expects three resources: one IORESOURCE_MEM resource defines the
memory region for the core's memory-mapped registers while a second
IORESOURCE_MEM resource defines the network packet buffer space. The third
resource, of type IORESOURCE_IRQ, associates an interrupt with the driver.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE
FPGA. Heavily based on Dave sources, I've just adopted it to current
kernel version and done some code cleanup.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Supporting AR8131, and AR8132.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same.  There's no reason to duplicate that much code.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Integrate the i2400m driver into the kernel's build and Kconfig.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a driver for the LAN9240 PCI ethernet adapter.

Changes since initial submission:
 - debug msg_level has been changed to use standard definitions
 - convert to use net_device_ops
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Another device using 8390 library that needs converting.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Another device using 8390 library that needs converting.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Another device using 8390 library that needs converting.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Another related 8390 driver. Since this is for nubus, not sure if
anyone still has the hardware?
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix hp-plus driver link errors.
Builds as loadable module and kernel image driver.
All drivers that use 8390.o or 8390p.o that will build on
i386 with MCA/PCI/EISA/ISA were built successfully both
=m and =y.

drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xac06c): undefined reference to `eip_interrupt'
hp-plus.c:(.text+0xac0d7): undefined reference to `eip_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xac1bb): undefined reference to `eip_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0xa98a): undefined reference to `NS8390p_init'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0xa9fe): undefined reference to `__alloc_eip_netdev'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.

There is an existing smc911x driver in the tree; this is intended to
replace it.  Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.

This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.

This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NBahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: NDustin Mcintire <dustin@sensoria.com>
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add support for the on-board Sonic Ethernet device for the XT2000
evaluation board.
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Supporting JMC250, and JMC260.
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Acked-and-tested-by: NEthan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Driver for Atheros L2 10/100 network device. Includes necessary
changes for Kconfig, Makefile, and pci_ids.h.
Signed-off-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix hp-plus Makefile object file:

drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt'
hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0x7407): undefined reference to `__alloc_ei_netdev'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114

Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The only user of the board, the extremly dated and rare MIPS Atlas board,
has been removed, so this driver can go, too.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Only a few ISA controllers need the pausing version of the 8390 core
while PCMCIA, later ISA and PCI do not. More importantly the ISA delays
can break non ISA boxes so we must use a different build of 8390.c for
the two sets of controllers.

No changes since last time as all the points of concerns raised proved to
be invalid
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

New Link code:
Moving all the link related code (including the calculations, the
initialization of the MAC and PHY and the external PHY's code) into
a separated file. The changes from the code that used to be part of
bnx2x.c (now called bnx2x_main.c) are:
- Using separate structures for link inputs and link outputs to clearly 
  identify what was configured and what is the outcome
- Adding code to read external PHY FW version and print it as part of 
  ethtool -i
- Adding code to upgrade external PHY FW from ethtool -E with special 
  magic number - Changing the link down indication to ERR level
- Adding a lock on all PHY access to prevent an interrupt and 
  setting changes to overlap
- Adding support for emulation and FPGA (small chunk of code that really 
  helps in the lab) - Adding support for 1G on BCM8706 PHY
- Adding clear debug print incase of fan failure (the PHY type is now 
  "failure")
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is the rename of bnx2x.c to bnx2x_main.c.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The arch/ppc sub-tree has been removed in the powerpc git tree.  The old
ibm_emac driver is no longer used by anything as a result of this.  This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This driver is for a number of different Option devices.  Originally
written by Option and Andrew Bird, but cleaned up massivly for
acceptance into mainline by me and others.

Many thanks to the following for their help in cleaning up the driver by
providing feedback and patches to it:
	- Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
	- Oliver Neukum <oliver@neukum.org>
	- Alan Cox <alan@lxorguk.ukuu.org.uk>
	- Javier Marcet <javier@krausbeck.org>

Cc: Andrew Bird <ajb@spheresystems.co.uk>
Cc: Javier Marcet <javier@krausbeck.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add support for Renesas SuperH Ethernet controller.  This driver supports
SH7710 and SH7712.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This driver has been superseded by fs_enet and is no longer in use.
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>