restructure the code which adds support for configuring
PCIe VF via mgmt netdevice. which was added by
commit 7829451c ("cxgb4: Add control net_device for
configuring PCIe VF")

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows userspace to attach eBPF filter to tun. This will
allow to implement VM dataplane filtering in a more efficient way
compared to cBPF filter by allowing either qemu or libvirt to
attach eBPF filter to tun.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be reused by other eBPF program other than queue selection.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to convert from mlxsw_sp_port to net_device and back again.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Benefit from the prepared TC and in-driver ACL infrastructure and
introduce block sharing offload. For that, a new struct "block" is
introduced in spectrum_acl in order to hold a list of specific
block-port bindings.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead, pass netdev and ingress flag to ruleset unbind op.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to prepare for follow-up changes, make the bind/unbind helpers
very simple. That required move of ht insertion/removal and bind/unbind
calls into mlxsw_sp_acl_ruleset_create/destroy.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver exports different switchdev PARENT_IDs for
representors belonging to different SR-IOV PF-pools of an adapter.
This is not correct as the adapter can switch across all vports
of an adapter. This patch fixes this by exporting a common switchdev
PARENT_ID for all reps of an adapter. The PCIE DSN is used as the id.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports 64-byte and 128-byte cache line size for more optimal
DMA performance when matched to the CPU cache line size.  The default is 64.
If the system is using 128-byte cache line size, set it to 128.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context.  This will allow "ip link show"
to display all VF MAC addresses.

Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.

Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_check_rings() is called by ethtool, XDP setup, and ndo_setup_tc()
to see if there are enough resources to support the new configuration.
Expand the call to test all resources if the firmware supports the new
API.  With the more flexible resource allocation scheme, this call must
be made to check that all resources are available before committing to
allocate the resources.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.

The min is the absolute minimum for each VF to function.  The max is the
global resources minus the resources used by the PF.  Each VF is
guaranteed the min.  Up to max resources may be available for some VFs.

The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources.  The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_rfs_capable(), add call to reserve vnic resources to support
NTUPLE.  Return true if we can successfully reserve enough vnics.
Otherwise, reserve the minimum 1 VNIC for normal operations not
supporting NTUPLE and return false.

Also, suppress warning message about not enough resources for NTUPLE when
only 1 RX ring is in use.  NTUPLE filters by definition require multiple
RX rings.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new method will call firmware to reserve the desired tx, rx, cmpl
rings, ring groups, stats context, and vnic resources.  A second query
call will check the actual resources that firmware is able to reserve.
The driver will then trim and adjust based on the actual resources
provided by firmware.  The driver will then reserve the final resources
in use.

This method is a more flexible way of using hardware resources.  The
resources are not fixed and can by adjusted by firmware.  The driver
adapts to the available resources that the firmware can reserve for
the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In combined mode, the driver is currently not setting RX and TX ring
numbers the same when firmware can allocate more RX than TX or vice versa.
This will confuse the user as the ethtool convention assumes they are the
same in combined mode.  Fix it by adding bnxt_trim_dflt_sh_rings() to trim
RX and TX ring numbers to be the same as the completion ring number in
combined mode.

Note that if TCs are enabled and/or XDP is enabled, the number of TX rings
will not be the same as RX rings in combined mode.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new API HWRM_FUNC_RESOURCE_QCAPS provides min and max hardware
resources.  Use the new API when it is supported by firmware.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources.  This new structure is common for PFs and VFs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After SRIOV has been enabled and disabled, the MSIX vectors assigned to
the VFs have to be re-initialized.  Otherwise they cannot be re-used by
the PF.  For example, increasing the number of PF rings after disabling
SRIOV may fail if the PF uses MSIX vectors previously assigned to the VFs.

To fix this, we add logic in bnxt_restore_pf_fw_resources() to close the
NIC, clear and re-init MSIX, and re-open the NIC.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new __bnxt_close_nic() function to do all the work previously done
in bnxt_close_nic() except waiting for SRIOV configuration.  The new
function will be used in the next patch as part of SRIOV cleanup.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The version has new firmware APIs to allocate PF/VF resources more
flexibly.

New toolchains were used to generate this file, resulting in a one-time
large diffstat.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).

Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).

SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Suggested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5

The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).

Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
  public S805 datasheet the only supported parent clock is MPLL2 (this
  was not verified using the oscilloscope).
  The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
  by 1", etc.) for the input clock. we call this clock the "m250_div"
  clock because it's value is always supposed to be (close to) 250MHz
  (see below for an explanation).
  The description in the public S805/S905 datasheet is a bit cryptic,
  but it comes down to "input clock = 250MHz * value" (which could also
  be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
  output from the m250_div and divides it by 2. This is not unusual on
  Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
  divide-by-2 clock.
  This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
  clock (which is an output on the MAC/SoC and an input in the PHY). we
  call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
  TX clock output is close to 0
  The description for this bit in the public S805/S905 datasheet is
  "Generate 25MHz clock for PHY". Based on these tests it's believed
  that this is wrong, and should probably read "Generate the 125MHz
  RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
  output (automatically) depending on the line speed (RGMII specifies
  that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
  25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
  100Mbit/s were tested with an oscilloscope). Due to the requirement
  that this clock always has to be set to 125MHz and due to the fixed
  divide-by-2 parent clock this means that m250_div will always end up
  with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
  of Amlogic's older GPL kernel sources.

The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.

This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).

Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.

While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0dfb33a0 ("sch_red: report backlog information") copied
child's backlog into RED's backlog.  Back then RED did not maintain
its own backlog counts.  This has changed after commit 2ccccf5f
("net_sched: update hierarchical backlog too") and commit d7f4f332
("sch_red: update backlog as well").  Copying is no longer necessary.

Tested:

$ tc -s qdisc show dev veth0
qdisc red 1: root refcnt 2 limit 400000b min 30000b max 30000b ecn
 Sent 20942 bytes 221 pkt (dropped 0, overlimits 0 requeues 0)
 backlog 1260b 14p requeues 14
  marked 0 early 0 pdrop 0 other 0
qdisc tbf 2: parent 1: rate 1Kbit burst 15000b lat 3585.0s
 Sent 20942 bytes 221 pkt (dropped 0, overlimits 138 requeues 0)
 backlog 1260b 14p requeues 14

Recently RED offload was added.  We need to make sure drivers don't
depend on resetting the stats.  This means backlog should be treated
like any other statistic:

  total_stat = new_hw_stat - prev_hw_stat;

Adjust mlxsw.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NNogah Frankel <nogahf@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an eBPF instruction is unknown to the driver JIT compiler, we can
reject the program at verification time.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Use the verifier log to output error messages if map lookup
can't be offloaded.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Currently in the cases where cmp_type == CMP_TYPE_RX_L2_TPA_START_CMP or
CMP_TYPE_RX_L2_TPA_END_CMP the exit path updates cpr->rx_bytes with an
uninitialized length len.  Fix this by adding a new exit path that does
not update the cpr stats with the bogus length len and remove the unused
label next_rx_no_prod.

Detected by CoverityScan, CID#1463807 ("Uninitialized scalar variable")
Fixes: 6a8788f2 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry().  The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sts variable is holding link speed as well as state.  We should
be using ls to index into ls_to_ethtool.

Fixes: 265aeb51 ("nfp: add support for .get_link_ksettings()")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: NYuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb len should be fetched before gro_receive - otherwise we may get
wrong or even outdated skb data.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal functions for registers and HW access were not prefixed.
This introduce noise in global kernel symbols. Here we add explicit prefix
'hw_atl' to all the HW access layer functions.
Alignment and styling were fixed as well.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Original driver code had internal registers and masks declarations
in low case and without any prefix.
Here we make all these uppercase and add already used HW_ATL prefix
to recognize these.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

aq_nic_s was hidden in aq_nic_internal.h, that made it difficult to access
nic fields and structures from other modules.
This change moves aq_nic_s struct into aq_nic.h and thus makes it available
to other driver modules, mainly pci module and hw related module.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliminate useless passing of net_device_ops and ethtools_ops through
deep chain of calls.
Move all pci related code into aq_pci_func module.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware operations and capabilities tables are constants and
never changed. Declare these as constants.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use direct aq_hw_s *self reference where possible
Eliminate useless abstraction PHAL, duplicated structures definitions,
Simplify nic config structure creation and management.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>