Make sure port DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:

- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
  the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
  data

This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.

This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.

Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For chipidea, the IP must know vbus before the controller
begins to run. So the .pullup should only be called when
the vbus is there.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CI_HDRC_REGS_SHARED stands for the controller registers is shared
with other USB drivers, if all USB drivers are at chipidea/, it doesn't
needed to be set.
CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This
flag doesn't need to be set if the vbus is always on for gadget
since dp has always pulled up after the gadget has initialized.

So, the current code seems to misuse this two flags.
- When the gadget initializes, the controller doesn't need to run if
it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to
shared register.
- When the gadget starts (load one gadget module), the controller
can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not
relate to shared register.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the gadget role starts, we need to make sure the vbus is lower
than OTGSC_BSV, or there will be an vbus interrupt since we use
B_SESSION_VALID as vbus interrupt to indicate connect and disconnect.
When the host role starts, it may not be useful to wait vbus to lower
than OTGSC_BSV, but it can indicate some hardware problems like the
vbus is still higher than OTGSC_BSV after we disconnect to host some
time later (5000 milliseconds currently), which is obvious not correct.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We add vbus interrupt handler at ci_otg_work, it uses OTGSC_BSV(at otgsc)
to know it is connect or disconnet event.
Meanwhile, we introduce two flags id_event and b_sess_valid_event to
indicate it is an id interrupt or a vbus interrupt.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move otg related things to otg file.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During the initialization, it needs to disable all interrupts
enable bit as well as clear all interrupts status bits to avoid
exceptional interrupt.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we need otgsc to know vbus's status at some chipidea
controllers even it is peripheral-only mode. Besides, some
SoCs (eg, AR9331 SoC) don't have otgsc register even
the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.

We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the
controller is dual role, but not supports OTG. If this flag is
not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC
are both 1 at CAP_DCCPARAMS, then this controller is otg capable.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

- The role's init will be called at probe procedure.
- The role's destroy will be called at fail patch
at probe and driver's removal.
- The role's start/stop will be called when specific
role has started.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This file is mainly used to access otgsc currently, it may
add otg related things in the future.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It is useless at below cases:
- If we implement both usb host and device at chipidea driver.
- If we don't need phy->otg.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For boards which have board level vbus control (eg, through gpio), we
need to vbus operation according to below rules:
- For host, we need open vbus before start hcd, and close it
after remove hcd.
- For otg, the vbus needs to be on/off when usb role switches.
When the host roles begins, it opens vbus; when the host role
finishes, it closes vbus.

We put vbus operation to host as host is the only vbus user,
When we are at host mode, the vbus is on, when we are not at
host mode, vbus should be off.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The vbus regulator is a common element for USB vbus operation,
So, move it from glue layer to core.
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After the rename to ci_hdrc we ended up with two MODULE_ALIAS entries, so
remove the old one.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 40dcd0e8 ("usb: chipidea: add PTW, PTS and STS handling") introduced
the following code to the ci_hdrc_probe() function:

+       if (!dev->of_node && dev->parent)
+               dev->of_node = dev->parent->of_node;

This inadvertently associates the ci_hdrc device with the ci_hdrc_imx
driver (which created the ci_hdrc device in the first place).

This results in ci_hdrc_imx_probe() being run for the ci_hdrc device
if ci_hdrc_probe() fails for some reason.
ci_hdrc_imx_probe() will happily create a new ci_hdrc platform_device
whose probing will likewise fail and trigger a new invocation of
ci_hdrc_imx_probe() ... ad nauseam.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Reviewed-and-tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a role fails to start, propagate the error code up the call stack
from probe.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This prevents the USB PHY refcount to be decremented below zero upon
unloading the ci-hdrc-imx module.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch provides a cleaner solution to the problem described in
commit 20a677fd ("usb: chipidea: improve kconfig").

The goal to be achieved is to force USB_CHIPIDEA=m if either
USB_EHCI_HCD=m or USB_GADGET=m.
If both are 'y' USB_CHIPIDEA may be selected to be 'm' or 'y'.

The old patch had the drawback, that USB_CHIPIDEA could be chosen as
'y' though USB_EHCI_HCD or USB_GADGET (or both) were 'm' leading to a
situation where USB_CHIPIDEA_HOST or USB_CHIPIDEA_UDC vanished from
the config options producing a compilable but dysfunctional driver.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove an unused macro leftover from the old initialization code.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently hw_phymode_configure() is located inside hw_device_reset(), which is
only called by chipidea udc driver.

When operating in host mode, we also need to call hw_phymode_configure() in
order to properly configure the PHY mode, so move this function into probe.

After this change, USB Host1 port on mx53qsb board is functional.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

'res' is not used anywhere, so let's get rid of it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if pdata is a NULL pointer we could cause a
kernel oops when probing the driver. Make sure
to cope with systems which won't pass pdata
to the driver.
Tested-by: NPaul Zimmerman <paulz@synopsys.com>
Reported-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

rh_call_control() contains a buffer, tbuf, which it uses to hold
USB descriptors. These discriptors are eventually copied into the
transfer_buffer in the URB. The buffer in the URB is dynamically
defined and is always large enough to hold the amount of data it
requests.

tbuf is currently statically allocated on the stack with a size
of 15 bytes, regardless of the size specified in the URB.
This patch dynamically allocates tbuf, and ensures that tbuf is
at least as big as the buffer in the URB.

If an hcd attempts to write a descriptor containing more than
15 bytes ( such as the Standard BOS Descriptor for hubs, defined
in the USB3.0 Spec, section 10.13.1 ) the write would overflow
the buffer and corrupt the stack. This patch addresses this
behavior.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSean O. Stalley <sean.stalley@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9841f37a ("usb: ehci: Add support for SINGLE_STEP_SET_FEATURE
test of EHSET") added additional code to the EHCI hub driver but it is
anticipated to only have a limited audience (e.g. embedded silicon
vendors and integrators). Avoid subjecting all EHCI (and in the future
maybe xHCI/OHCI, etc.) HCD users to code bloat by conditionally
compiling the EHSET-specific additions with a new Kconfig option,
CONFIG_USB_HCD_TEST_MODE.
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver currently knows about 3 different PL2303 chip types:
The two legacy chip types type_0 and type_1 (PL2303H ?) and the HX
type.
The device distinction is currently completely based on the examination
of the USB descriptors.
During the last years, Prolific has introduced further PL2303 chips,
such as the HXD (HX rev. D), TA (which replaced the X/HX chips), SA,
RA, EA and TB variants.
Unfortunately, all these new chips are currently detected as HX chips,
because they are all using the same bMaxPacketSize0 = 0x40 value in the
USB device descriptor.

At this point it is not clear if these chips are really working with
the driver, there are just some positive indicators (like device
manufacturers claiming Linux support for these devices or commit
8d48fdf6 "correctly handle baudrates above 115200" which should only
be necessary for newer devices, ...)

For a complete support of all devices, we need to distinguish between
them, because they differ in several functional aspects, such  as the
maximum supported baud rate (HXD, TB, EA: 12Mbps, HX, TA: 6Mbps,
RA: 1Mbps, SA: 115.2kbps), handshaking line support, RS422/485 and
GPIO ports support (currently not supported by the driver).
And there might be further differences that we don't know yet.

This patch improves the chip type detection by evaluating the bcdDevice
value of the device descriptor. The values are taken from the
datasheets and are safe to use because manufacturers can't change them:

3.00: X/HX, TA
4.00: HXD, EA, RA, SA
5.00: TB

The rest of the device descriptors is completely identical, so no
further distinction is possible this way.
Anyway, Prolifics "checkChipVersion.exe"-tool is definitely able to
distinguish for example between the X/HX and the TA chips, so there
must be a possibility to improve the distinction further...
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The chip type distinction is getting more and more relevant and
complicating, so always print the chip type.
Printing a name string is also much better than just printing an
internal index number.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need for two else-if constructs for the type_1 chip
detection in pl2303_startup(), so merge them.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Stephen Rothwell reported that this driver does not compile on PowerPC
due to this missing include. One could argue why this driver is enabled
on PowerPC in the first place but it sure isn't wrong to include headers
for used function instead of to rely that they sneak in.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the musb-gadget code now calls the dma engine properly it is
possible to enable it for the TX path in device mode.
AM335x Advisory 1.0.13 says that we may lose the toggle bit on multiple
RX transfers. There is a workaround in host mode but none in device mode
and therefore RX transfers are disabled.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch makes use of the two function is_cppi_enabled() and
tusb_dma_omap() instead of the ifdef for the proper DMA implementation
setup code. It basically shifts the code right by one indention level
and adds a few line breaks once the chars are crossed.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

I've found some new datasheets which describe some additionally
supported standard baud rates and I've verified them with my HX
(rev. 3A) device. But adding support for individual (chip type
specific) baud rates would add a good amount of extra code (especially
when support for further chips will be added to the driver one day),
which makes no sense as long as we are not using the direct baud rate
encoding method for newer chips.
So for now, just drop a comment about these additionally supported baud
rates.

The second comment is about the baud rate differences between the two
encoding methods. In theory, we could optimize the code a bit by
comparing the resulting baud rates of both methods and selecting the
one which is closer to the requested baud rate. But that seems to be a
bit overkill, because the differences are very small and the device
likely uses the same baud rate generator for both methods so that the
resulting baud rate would be the same.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips

Now that the divisor based baud rate encoding method has been fixed and
extended, it can also be used for baud rates < 115200 baud with HX
chips.
This makes it possible to adjust the baud rate almost continuously
instead of just beeing able to select between 16 fixed standard values.

Tested with a PL2303HX 04463A (week 46, 2004, rev 3A).
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reinhard Max has done some tests with a PL2303HX (rev A) and a logic
analyzer and it seems, that although the PL2303HX is specified for baud
rates from 75 to 6M baud, the full divisor range can be used with the
divisor based baud rate encoding method. This corresponds to baud rates
from 46 to 24M baud.
Baud rates down to 46 baud (max. divisor) have been confirmed to work
even under heavy/permanent load, so remove the lower limit.
Baud rates up to 24M baud should really be tested carefully in "real
life" scenarios before removing the upper limit completely.
Anyway, the Windows driver allows maximum baud rates of 110% of the
specified limit, so for now, increase the upper limit to this value.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NReinhard Max <max@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 0c967e7e "USB: serial: pl2303 works at 500kbps" added 500000
baud to the list of supported standard baud rates.
But the reason why the driver works with this baud rate is, that since
commit 8d48fdf6 "USB: PL2303: correctly handle baudrates above 115200"
a second (divisor based) baud rate encoding method is used for values
above 115200 baud, which is not limited to a fixed set of standard baud
rates.

Remove the 500000 baud value from the list of standard baud rates
again, because this list is only used with the direct baud rate
encoding method and 500000 baud is not supported with this method.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method

In opposition to the direct baud rate encoding method, the divisor
based method is not limited to a fixed set of standard baud rates.
Hence, there is no need to round to the next nearest standard value.
Reported-by: NMastro Gippo <gipmad@gmail.com>
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NReinhard Max <max@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on the formula in the code description, Reinhard Max and me have
investigated the devices behavior / functional principle of the divisor
based baud rate encoding method.

It turned out, that (although beeing a good starting point) the current
code has some flaws. It doesn't work correctly for a wide range of baud
rates and the divisor resolution can be improved. It also doesn't
report the actually set baud rate.

This patch fixes and improves the code for the divisor based baud rate
encoding method a lot. It can now be used for the whole range of baud
rates from 46 baud to 24M baud with a very good divisor resolution and
userspace can read back the resulting baud rate.

It also documents the formula used for encoding and the hardware
behavior (including special cases).

The basic algorithm, rounding and several code comments/explanations
are provided by Reinhard Max.
I've added some minor fixes, the handling of the special cases and
further code/algorithm descriptions.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NReinhard Max <max@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>