- 20 9月, 2016 1 次提交
-
-
由 Roi Dayan 提交于
The FW command output length should be only the length of struct mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy call which is invoked later in the driver to write over wrong memory address and corrupt kernel memory which results in random crashes. This bug was found using the kernel address sanitizer (kasan). Fixes: a351a1b0 ('net/mlx5: Introduce bulk reading of flow counters') Signed-off-by: NRoi Dayan <roid@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 9月, 2016 2 次提交
-
-
由 David S. Miller 提交于
Merge tag 'mac80211-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Two more fixes: * reject aggregation sessions for TSID/TID 8-16 that we can never use anyway and which could confuse drivers * check return value of skb_linearize() ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe CAVALLARO 提交于
MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status register to generate power management events. So this patch is to properly set the RWKPKTEN [BIT(2)] inside the PMT register (needed in case of global unicast). Reported-by: NAditi SHARMA <aditi-hed.sharma@st.com> Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 9月, 2016 7 次提交
-
-
由 Ivan Vecera 提交于
Commit 6e7333d3 "net: add rx_nohandler stat counter" added the new entry rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna driver foolishly depends on the structure. It uses part of it for ethtool statistics and it's not bad but the driver assumes its size is constant as it defines string for each existing entry. The problem occurs when the structure is extended because you need to modify bna driver as well. If not any attempt to retrieve ethtool statistics results in crash in bnad_get_strings(). The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of strings in the array and also removes rtnl_link_stats64 entries that are not used in output and are always zero. Fixes: 6e7333d3 "net: add rx_nohandler stat counter" Signed-off-by: NIvan Vecera <ivecera@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Vecera 提交于
Commit ba5ca784 "bna: check for dma mapping errors" added besides other things a statistic that counts number of DMA buffer mapping failures per each Rx queue. This counter is not included in ethtool stats output. Fixes: ba5ca784 "bna: check for dma mapping errors" Signed-off-by: NIvan Vecera <ivecera@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcelo Ricardo Leitner 提交于
This function actually operates on u32 yet its paramteres were declared as u16, causing integer truncation upon calling. Note in patch context that ADDIP_SERIAL_SIGN_BIT is already 32 bits. Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 phil.turnbull@oracle.com 提交于
skb is not freed if newsk is NULL. Rework the error path so free_skb is unconditionally called on function exit. Fixes: c3ea9fa2 ("[IrDA] af_irda: IRDA_ASSERT cleanups") Signed-off-by: NPhil Turnbull <phil.turnbull@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
A malicious TCP receiver, sending SACK, can force the sender to split skbs in write queue and increase its memory usage. Then, when socket is closed and its write queue purged, we might overflow sk_forward_alloc (It becomes negative) sk_mem_reclaim() does nothing in this case, and more than 2GB are leaked from TCP perspective (tcp_memory_allocated is not changed) Then warnings trigger from inet_sock_destruct() and sk_stream_kill_queues() seeing a not zero sk_forward_alloc All TCP stack can be stuck because TCP is under memory pressure. A simple fix is to preemptively reclaim from sk_mem_uncharge(). This makes sure a socket wont have more than 2 MB forward allocated, after burst and idle period. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
If a TCP socket gets a large write queue, an overflow can happen in a test in __tcp_retransmit_skb() preventing all retransmits. The flow then stalls and resets after timeouts. Tested: sysctl -w net.core.wmem_max=1000000000 netperf -H dest -- -s 1000000000 Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Filipe Manco 提交于
In case of error during netback_probe() (e.g. an entry missing on the xenstore) netback_remove() is called on the new device, which will set the device backend state to XenbusStateClosed by calling set_backend_state(). However, the backend state wasn't initialized by netback_probe() at this point, which will cause and invalid transaction and set_backend_state() to BUG(). Initialize the backend state at the beginning of netback_probe() to XenbusStateInitialising, and create two new valid state transitions on set_backend_state(), from XenbusStateInitialising to XenbusStateClosed, and from XenbusStateInitialising to XenbusStateInitWait. Signed-off-by: NFilipe Manco <filipe.manco@neclab.eu> Acked-by: NWei Liu <wei.liu2@citrix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 9月, 2016 16 次提交
-
-
由 David S. Miller 提交于
Ursula Braun says: ==================== 390: qeth patches here are several fixes for the s390 qeth driver, built for net. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Thomas Richter 提交于
commit 5f78e29c ("qeth: optimize IP handling in rx_mode callback") restructured the internal address handling. This work broke setting a virtual IP address. The command echo 10.1.1.1 > /sys/bus/ccwgroup/devices/<device>/vipa/add4 fails with file exist error even if the IP address has not been set before. It turned out that the search result for the IP address search is handled incorrectly in the VIPA case. This patch fixes the setting of an virtual IP address. Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
According to recent performance measurements, turning on net_device feature NETIF_F_SG only behaves well, but turning on feature NETIF_F_GSO shows bad results. Since the kernel activates NETIF_F_GSO automatically as soon as the driver configures feature NETIF_F_SG, qeth should not activate feature NETIF_F_SG per default, until the qeth problems with NETIF_F_GSO are solved. Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
To reduce the need of skb_linearize() calls, gso_max_segs of qeth net_devices had been limited according to the maximum number of qdio SBAL elements. But a gso segment cannot be larger than the mtu-size, while an SBAL element can contain up to 4096 bytes. The gso_max_segs limitation limits the maximum packet size given to the qeth driver. Performance measurements with tso-enabled qeth network interfaces and mtu-size 1500 showed, that the disadvantage of smaller packets is much more severe than the advantage of fewer skb_linearize() calls. This patch gets rid of the gso_max_segs limitations in the qeth driver. Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
af_iucv socket programs with HiperSockets as transport make use of the qdio completion queue. Running such an af_iucv socket program may result in a crash: [90341.677709] Oops: 0038 ilc:2 [#1] SMP [90341.677743] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.6.0-20160720.0.0e86ec7.5e62689.fc23.s390xperformance #1 [90341.677744] Hardware name: IBM 2964 N96 703 (LPAR) [90341.677746] task: 00000000edb79f00 ti: 00000000edb84000 task.ti: 00000000edb84000 [90341.677748] Krnl PSW : 0704d00180000000 000000000075bc50 (qeth_qdio_input_handler+0x258/0x4e0) [90341.677756] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3 Krnl GPRS: 000003d10391e900 0000000000000001 00000000e61e6000 0000000000000005 [90341.677759] 0000000000a9e6ec 5420040001a77400 0000000000000001 000000000000006f [90341.677761] 00000000e0d83f00 0000000000000003 0000000000000010 5420040001a77400 [90341.677784] 000000007ba8b000 0000000000943fd0 000000000075bc4e 00000000ed3b3c10 [90341.677793] Krnl Code: 000000000075bc42: e320cc180004 lg %r2,3096(%r12) 000000000075bc48: c0e5ffffc5cc brasl %r14,7547e0 #000000000075bc4e: 1816 lr %r1,%r6 >000000000075bc50: ba19b008 cs %r1,%r9,8(%r11) 000000000075bc54: ec180041017e cij %r1,1,8,75bcd6 000000000075bc5a: 5810b008 l %r1,8(%r11) 000000000075bc5e: ec16005c027e cij %r1,2,6,75bd16 000000000075bc64: 5090b008 st %r9,8(%r11) [90341.677807] Call Trace: [90341.677810] ([<000000000075bbc0>] qeth_qdio_input_handler+0x1c8/0x4e0) [90341.677812] ([<000000000070efbc>] qdio_kick_handler+0x124/0x2a8) [90341.677814] ([<0000000000713570>] __tiqdio_inbound_processing+0xf0/0xcd0) [90341.677818] ([<0000000000143312>] tasklet_action+0x92/0x120) [90341.677823] ([<00000000008b6e72>] __do_softirq+0x112/0x308) [90341.677824] ([<0000000000142bce>] irq_exit+0xd6/0xf8) [90341.677829] ([<000000000010b1d2>] do_IRQ+0x6a/0x88) [90341.677830] ([<00000000008b6322>] io_int_handler+0x112/0x220) [90341.677832] ([<0000000000102b2e>] enabled_wait+0x56/0xa8) [90341.677833] ([<0000000000000000>] (null)) [90341.677835] ([<0000000000102e32>] arch_cpu_idle+0x32/0x48) [90341.677838] ([<000000000018a126>] cpu_startup_entry+0x266/0x2b0) [90341.677841] ([<0000000000113b38>] smp_start_secondary+0x100/0x110) [90341.677843] ([<00000000008b68a6>] restart_int_handler+0x62/0x78) [90341.677845] ([<00000000008b6588>] psw_idle+0x3c/0x40) [90341.677846] Last Breaking-Event-Address: [90341.677848] [<00000000007547ec>] qeth_dbf_longtext+0xc/0xc0 [90341.677849] [90341.677850] Kernel panic - not syncing: Fatal exception in interrupt qeth_qdio_cq_handler() analyzes SBALs on this completion queue, but does not observe the limit of 16 SBAL elements per SBAL. This patch adds the additional check to process not more than 16 SBAL elements. Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
The qeth IP address mapping logic has been reworked recently. It causes now problems to specify qeth sysfs attribute "hsuid" in DOWN state, which is allowed. Postpone registering or deregistering of IP-addresses in this case. Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
qeth_l3_dev_hsuid_store() changes the ip hash table, which requires the ip_lock. Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hans Wippel 提交于
After device recovery, only a basic set of network device features is enabled on the device. If features like checksum offloading or TSO were enabled by the user before the recovery, this results in a mismatch between the network device features, that the kernel assumes to be enabled on the device, and the features actually enabled on the device. This patch tries to restore previously set features, that require changes on the device, after the recovery of a device. In case of an error, the network device's features are changed to contain only the features that are actually turned on. Signed-off-by: NHans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 73725d9d ("nfp: allocate ring SW structs dynamically") Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com> Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Mark Tomlinson 提交于
The function ip_rcv_finish() calls l3mdev_ip_rcv(). On any VRF except the global VRF, this replaces skb->dev with the VRF master interface. When calling ip_route_input_noref() from here, the checks for forwarding look at this master device instead of the initial ingress interface. This will allow packets to be routed which normally would be dropped. For example, an interface that is not assigned an IP address should drop packets, but because the checking is against the master device, the packet will be forwarded. The fix here is to still call l3mdev_ip_rcv(), but remember the initial net_device. This is passed to the other functions within ip_rcv_finish, so they still see the original interface. Signed-off-by: NMark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Acked-by: NDavid Ahern <dsa@cumulusnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Mikhaylov 提交于
for preventing race conditions within ioctl calls. Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Mikhaylov 提交于
add realization for mac address set and remove dummy callback. Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sean Wang 提交于
The device table is required to load modules based on modaliases. After adding MODULE_DEVICE_TABLE, below entries for example will be added to modules.alias: alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc Signed-off-by: NSean Wang <sean.wang@mediatek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.open-mesh.org/linux-merge由 David S. Miller 提交于
Simon Wunderlich says: ==================== Here are two batman-adv bugfix patches: - Fix reference counting for last_bonding_candidate, by Sven Eckelmann - Fix head room reservation for ELP packets, by Linus Luessing ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sebastian Ott 提交于
If an error occurs in mlx4_init_eq_table the index used in the err_out_unmap label is one too big which results in a panic in mlx4_free_eq. This patch fixes the index in the error path. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: NTariq Toukan <tariqt@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'mac80211-for-davem-2016-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== A few more fixes: * better mesh path fixing, from Thomas * fix TIM IE recalculation after sending frames to a sleeping station, from Felix * fix sequence number assignment while sending frames to a sleeping station, also from Felix * validate number of probe response CSA counter offsets, fixing a copy/paste bug (from myself) ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 9月, 2016 1 次提交
-
-
由 Johannes Berg 提交于
Since mac80211 doesn't currently support TSIDs 8-15 which can only be used after QoS TSPEC negotiation (and not even after WMM negotiation), reject attempts to set up aggregation sessions for them, which might confuse drivers. In mac80211 we do correctly handle that, but the TSIDs should never get used anyway, and drivers might not be able to handle it. Cc: stable@vger.kernel.org Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 14 9月, 2016 3 次提交
-
-
由 Johannes Berg 提交于
The A-MSDU TX code (within TXQs) didn't always check the return value of skb_linearize() properly, resulting in potentially passing a frag- list SKB down to the driver even when it said it can't handle it. Fix that. Fixes: 6e0456b5 ("mac80211: add A-MSDU tx support") Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Due to an apparent copy/paste bug, the number of counters for the beacon configuration were checked twice, instead of checking the number of probe response counters. Fix this to check the number of probe response counters before parsing those. Cc: stable@vger.kernel.org Fixes: 9a774c78 ("cfg80211: Support multiple CSA counters") Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Christophe Jaillet 提交于
If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)' will do nothing. It is likely that 'if (!IS_ERR(pdata->clk))' was expected here. In fact, the test can even be removed because 'clk_disable_unprepare' already handles such cases. Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 9月, 2016 5 次提交
-
-
由 Xin Long 提交于
Since commit 4f008781 ("sctp: apply rhashtable api to send/recv path"), sctp uses transport rhashtable with .obj_cmpfn sctp_hash_cmp, in which it compares the members of the transport with the rhashtable args to check if it's the right transport. But sctp uses the transport without holding it in sctp_hash_cmp, it can cause a use-after-free panic. As after it gets transport from hashtable, another CPU may close the sk and free the asoc. In sctp_association_free, it frees all the transports, meanwhile, the assoc's refcnt may be reduced to 0, assoc can be destroyed by sctp_association_destroy. So after that, transport->assoc is actually an unavailable memory address in sctp_hash_cmp. Although sctp_hash_cmp is under rcu_read_lock, it still can not avoid this, as assoc is not freed by RCU. This patch is to hold the transport before checking it's members with sctp_transport_hold, in which it checks the refcnt first, holds it if it's not 0. Fixes: 4f008781 ("sctp: apply rhashtable api to send/recv path") Signed-off-by: NXin Long <lucien.xin@gmail.com> Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Baoquan He 提交于
When system enters into kdump kernel because of kernel panic, it won't shutdown devices. On-flight DMA will continue transferring data until device driver initializes. All devices are supposed to reset during driver initialization. And this property is used to fix the kdump failure in system with intel iommu. Other systems with hardware iommu should be similar. Please check commit 091d42e4 ("iommu/vt-d: Copy translation tables from old kernel") and those commits around. But bnx2 driver doesn't reset device during driver initialization. The device resetting is deferred to net device up stage. This will cause hardware iommu handling failure on bnx2 device. And its resetting relies on firmware. So in this patch move the firmware requesting code to earlier bnx2_init_one(), then next call bnx2_reset_chip to reset device. Signed-off-by: NBaoquan He <bhe@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf由 David S. Miller 提交于
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for your net tree, they are: 1) Endianess fix for the new nf_tables netlink trace infrastructure, NFTA_TRACE_POLICY endianess was not correct, patch from Liping Zhang. 2) Fix broken re-route after userspace queueing in nf_tables route chain. This patch is large but it is simple since it is just getting this code in sync with iptable_mangle. Also from Liping. 3) NAT mangling via ctnetlink lies to userspace when nf_nat_setup_info() fails to setup the NAT conntrack extension. This problem has been there since the beginning, but it can now show up after rhashtable conversion. 4) Fix possible NULL pointer dereference due to failures in allocating the synproxy and seqadj conntrack extensions, from Gao feng. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gao Feng 提交于
When memory is exhausted, nfct_seqadj_ext_add may fail to add the synproxy and seqadj extensions. The function nf_ct_seqadj_init doesn't check if get valid seqadj pointer by the nfct_seqadj. Now drop the packet directly when fail to add seqadj extension to avoid dereference NULL pointer in nf_ct_seqadj_init from init_conntrack(). Signed-off-by: NGao Feng <fgao@ikuai8.com> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Pablo Neira Ayuso 提交于
nf_nat_setup_info() returns NF_* verdicts, so convert them to error codes that is what ctnelink expects. This has passed overlook without having any impact since this nf_nat_setup_info() has always returned NF_ACCEPT so far. Since 870190a9 ("netfilter: nat: convert nat bysrc hash to rhashtable"), this is problem. Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
- 12 9月, 2016 5 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: "Mostly small sets of driver fixes scattered all over the place. 1) Mediatek driver fixes from Sean Wang. Forward port not written correctly during TX map, missed handling of EPROBE_DEFER, and mistaken use of put_page() instead of skb_free_frag(). 2) Fix socket double-free in KCM code, from WANG Cong. 3) QED driver fixes from Sudarsana Reddy Kalluru, including a fix for using the dcbx buffers before initializing them. 4) Mellanox Switch driver fixes from Jiri Pirko, including a fix for double fib removals and an error handling fix in mlxsw_sp_module_init(). 5) Fix kernel panic when enabling LLDP in i40e driver, from Dave Ertman. 6) Fix padding of TSO packets in thunderx driver, from Sunil Goutham. 7) TCP's rcv_wup not initialized properly when using fastopen, from Neal Cardwell. 8) Don't use uninitialized flow keys in flow dissector, from Gao Feng. 9) Use after free in l2tp module unload, from Sabrina Dubroca. 10) Fix interrupt registry ordering issues in smsc911x driver, from Jeremy Linton. 11) Fix crashes in bonding having to do with enslaving and rx_handler, from Mahesh Bandewar. 12) AF_UNIX deadlock fixes from Linus. 13) In mlx5 driver, don't read skb->xmit_mode after it might have been freed from the TX reclaim path. From Tariq Toukan. 14) Fix a bug from 2015 in TCP Yeah where the congestion window does not increase, from Artem Germanov. 15) Don't pad frames on receive in NFP driver, from Jakub Kicinski. 16) Fix chunk fragmenting in SCTP wrt. GSO, from Marcelo Ricardo Leitner. 17) Fix deletion of VRF routes, from Mark Tomlinson. 18) Fix device refcount leak when DAD fails in ipv6, from Wei Yongjun" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits) net/mlx4_en: Fix panic on xmit while port is down net/mlx4_en: Fixes for DCBX net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state() net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all() net: ethernet: renesas: sh_eth: add POST registers for rz drivers: net: phy: mdio-xgene: Add hardware dependency dwc_eth_qos: do not register semi-initialized device sctp: identify chunks that need to be fragmented at IP level mlxsw: spectrum: Set port type before setting its address mlxsw: spectrum_router: Fix error path in mlxsw_sp_router_init nfp: don't pad frames on receive nfp: drop support for old firmware ABIs nfp: remove linux/version.h includes tcp: cwnd does not increase in TCP YeAH net/mlx5e: Fix parsing of vlan packets when updating lro header net/mlx5e: Fix global PFC counters replication net/mlx5e: Prevent casting overflow net/mlx5e: Move an_disable_cap bit to a new position net/mlx5e: Fix xmit_more counter race issue tcp: fastopen: avoid negative sk_forward_alloc ...
-
由 Pedersen, Thomas 提交于
A fixed mpath was not quite being treated as such: 1) if a PERR frame was received, a fixed mpath was deactivated. 2) queued path discovery for fixed mpath was potentially being considered, changing mpath state. 3) other mpath flags were potentially being inherited when fixing the mpath. Just assign PATH_FIXED and SN_VALID. This solves several issues when fixing a mesh path in one direction. The reverse direction mpath should probably also be fixed, or root announcements at least be enabled. Signed-off-by: NThomas Pedersen <twp@qca.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Felix Fietkau 提交于
When using intermediate queues, sequence number allocation is deferred until dequeue. This doesn't work for PS response frames, which bypass those queues. Signed-off-by: NFelix Fietkau <nbd@nbd.name> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Felix Fietkau 提交于
Handle the case where the mac80211 intermediate queues are empty and the driver has buffered frames Fixes: ba8c3d6f ("mac80211: add an intermediate software queue implementation") Signed-off-by: NFelix Fietkau <nbd@nbd.name> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Linus Torvalds 提交于
-