The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed duplicated #include <rdma/ib_verbs.h> in net/9p/trans_rdma.c
		and  #include <linux/thread_info.h> in net/socket.c
Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.

So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.

	This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch gets about 1.25% back on tbench regression.

My change to NAPI for multiqueue support changed the time limit on
network receive processing.  Under sustained loads like tbench, this
can cause the receiver to reschedule prematurely. 
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

put_dec_trunc prints the digits in reverse order and is reversed
inside number(). Continue using put_dec_trunc, but reverse each quad
in ip4_addr_string.

[Noticed by Julius Volz]
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the 'supports_ipv6' scheduler flag since all schedulers now
support IPv6.
Signed-off-by: NJulius Volz <julius.volz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IPv6 support to LBLC and LBLCR schedulers. These were the last
schedulers without IPv6 support, but we might want to keep the
supports_ipv6 flag in the case of future schedulers without IPv6
support.
Signed-off-by: NJulius Volz <julius.volz@gmail.com>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version to 3.95.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the expansion register access routines a little more
formal.  They will be used by the following bcm50610 support patch.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds flow control support to Broadcom phys.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines support for the 5785 device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines the phylib support in the tg3 driver.  The patch does
the following things :

* Rename tg3_mdio_config() to tg3_mdio_config_5785().  The 5785 will be
  the only device that will use it so the name might as well reflect
  that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
  MAC <=> PHY interface.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows WOL to be enabled for Broadcom phys under phylib
control.  The only exception is the AC131, which has a completely
different register set.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 12dac075 ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver.  The patch was understandably conservative, so this patch
elaborates on that work.

The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL.  The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.

The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled.  The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, phylib reports appear with a eth%d prefix.  Move the line
after register_netdev() and place it alongside the other informative
messages.  Update nearby informative messages accordingly.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled.  Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag.  It only
used twice in non-fast paths.  This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the __tg3_set_mac_addr() function earlier in the file
listing, to avoid a function prototype, and calls the function to
restore the LAA after a driver unload chip reset.  With this code in
place, the administrator can wake the machine using the LAA.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.

When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames.  Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver.  The first hunk of this patch preserves this setting.

The second hunk of this patch wipes out the driver present signature of
the APE memory space.  By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the existing APE register mapping code with a call
to pci_ioremap_bar().  The code that maps the main device register space
did not undergo a similar change because the information derived from
the pci_resource_start() and pci_resource_len() is still used to
populate the (optional) mem_start and mem_end netdevice members.
Replace hardcoded constants where appropriate.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 5761S chip variants.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since gso_skb is re-used for qdisc_peek_dequeued(), and this skb is
counted in the qdisc->q.qlen, it has to be kfreed during qdisc_reset()
when qlen is zeroed.

With help from David S. Miller <davem@davemloft.net>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Stephen Hemminger.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IPv6 support to SH and DH schedulers. I hope this simple IPv6 address
hashing is good enough. The 128 bit are just XORed into 32 before hashing
them like an IPv4 address.
Signed-off-by: NJulius Volz <julius.volz@gmail.com>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This documentation patch hopes to clarify that the '+' was only needed
for Fedora 7 and Red Hat Enterprise Linux 5.0 and 5.1.  After that the
IP addreses could be added as a comma separated list just like the
module option.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The smc_drv_probe() is the platform_driver probe function and it is only
called during init.  Further, it calls smc_probe() which is marked as __init
already.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This eliminates the following often-generated warning from my 64 bit
Opteron SMP test stand:

	eth0: too many iterations (6) in nv_nic_irq

According to the web, the problem is that the forcedeth driver has a
too-low value for max_interrupt_work.  Grepping the kernel I see that
forcedeth has the second lowest value of all ethernet drivers (ie, 6).
Most are in the 20-40 range.  So this patch increases this a bit, from 6
to 15 (at 15 forcedeth becomes the driver with third-lowest
max_interrupt_work value).

My test stand, which used to print out the above warnings repetitively
whenever it was under heavy net load, no longer does so.
Signed-off-by: NJoe Korty <joe.korty@ccur.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>