Currently perf has its own list function within the ftrace infrastructure
that seems to be used only to allow for it to have per-cpu disabling as well
as a check to make sure that it's not called while RCU is not watching. It
uses something called the "control_ops" which is used to iterate over ops
under it with the control_list_func().

The problem is that this control_ops and control_list_func unnecessarily
complicates the code. By replacing FTRACE_OPS_FL_CONTROL with two new flags
(FTRACE_OPS_FL_RCU and FTRACE_OPS_FL_PER_CPU) we can remove all the code
that is special with the control ops and add the needed checks within the
generic ftrace_list_func().
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When showing all tramps registered to a ftrace record in the file
enabled_functions, it exits the loop with ops == NULL. But then it is
suppose to show the function on the ops->trampoline and
add_trampoline_func() is called with the given ops. But because ops is now
NULL (to exit the loop), it always shows the static trampoline instead of
the one that is really registered to the record.

The call to add_trampoline_func() that shows the trampoline for the given
ops needs to be called at every iteration.

Fixes: 39daa7b9 "ftrace: Show all tramps registered to a record on ftrace_bug()"
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

s/ARCH_SUPPORT_FTARCE_OPS/ARCH_SUPPORTS_FTRACE_OPS/

Link: http://lkml.kernel.org/r/1448879016-8659-1-git-send-email-huawei.libin@huawei.comSigned-off-by: NLi Bin <huawei.libin@huawei.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When an anomaly is detected in the function call modification code,
ftrace_bug() is called to disable function tracing as well as give any
information that may help debug the problem. Currently, only the first found
trampoline that is attached to the failed record is reported. Instead, show
all trampolines that are hooked to it.

Also, not only show the ops pointer but also report the function it calls.

While at it, add this info to the enabled_functions debug file too.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When an anomaly is found while modifying function code, ftrace_bug() is
called which disables the function tracing infrastructure and reports
information about what failed. If the code that is to be replaced does not
match what is expected, then actual code is shown. Currently there is no
arch generic way to show what was expected.

Add a new variable pointer calld ftrace_expected that the arch code can set
to point to what it expected so that ftrace_bug() can report the actual text
as well as the text that was expected to be there.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The ftrace function hook utility has several internal checks to make sure
that whatever it modifies is exactly what it expects to be modifying. This
is essential as modifying running code can be extremely dangerous to the
system.

When an anomaly is detected, ftrace_bug() is called which sends a splat to
the console and disables function tracing. There's some extra information
that is printed to help diagnose the issue.

One thing that is missing though is output of what ftrace was doing at the
time of the crash. Was it updating a call site or perhaps converting a call
site to a nop? A new global enum variable is created to state what ftrace
was doing at the time of the anomaly, and this is reported in ftrace_bug().
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Extend module command for function filter selection with globbing.
It uses the same globbing as function filter.

  sh# echo '*alloc*:mod:*' > set_ftrace_filter

Will trace any function with the letters 'alloc' in the name in any
module but not in kernel.

  sh# echo '!*alloc*:mod:ipv6' >> set_ftrace_filter

Will prevent from tracing functions with 'alloc' in the name from module
ipv6 (do not forget to append to set_ftrace_filter file).

  sh# echo '*alloc*:mod:!ipv6' > set_ftrace_filter

Will trace functions with 'alloc' in the name from kernel and any
module except ipv6.

  sh# echo '*alloc*:mod:!*' > set_ftrace_filter

Will trace any function with the letters 'alloc' in the name only from
kernel, but not from any module.

  sh# echo '*:mod:!*' > set_ftrace_filter
or
  sh# echo ':mod:!' > set_ftrace_filter

Will trace every function in the kernel, but will not trace functions
from any module.

  sh# echo '*:mod:*' > set_ftrace_filter
or
  sh# echo ':mod:' > set_ftrace_filter

As the opposite will trace all functions from all modules, but not from
kernel.

  sh# echo '*:mod:*snd*' > set_ftrace_filter

Will trace your sound drivers only (if any).

Link: http://lkml.kernel.org/r/1443545176-3215-4-git-send-email-0x7f454c46@gmail.comSigned-off-by: NDmitry Safonov <0x7f454c46@gmail.com>
[ Made format changes ]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

ftrace_match parameters are very related and I reduce the number of local
variables & parameters with it.
This is also preparation for module globbing as it would introduce more
realated variables & parameters.

Link: http://lkml.kernel.org/r/1443545176-3215-3-git-send-email-0x7f454c46@gmail.comSigned-off-by: NDmitry Safonov <0x7f454c46@gmail.com>
[ Made some formatting changes ]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

"Not" is too abstract variable name - changed to clear_filter.
Removed ftrace_match_module_records function: comparison with !* or *
not does the general code in filter_parse_regex() as it works without
mod command for
  sh# echo '!*' > /sys/kernel/debug/tracing/set_ftrace_filter

Link: http://lkml.kernel.org/r/1443545176-3215-2-git-send-email-0x7f454c46@gmail.comSigned-off-by: NDmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

By now there isn't any subcommand for mod.

Before:
	sh$ echo '*:mod:ipv6:a' > set_ftrace_filter
	sh$ echo '*:mod:ipv6' > set_ftrace_filter
had the same results, but now first will result in:
	sh$ echo '*:mod:ipv6:a' > set_ftrace_filter
	-bash: echo: write error: Invalid argument

Also, I clarified ftrace_mod_callback code a little.

Link: http://lkml.kernel.org/r/1443545176-3215-1-git-send-email-0x7f454c46@gmail.comSigned-off-by: NDmitry Safonov <0x7f454c46@gmail.com>
[ converted 'if (ret == 0)' to 'if (!ret)' ]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

__trace_sched_switch_state() is the last remaining PREEMPT_ACTIVE
user, move trace_sched_switch() from prepare_task_switch() to
__schedule() and propagate the @preempt argument.
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

To cover the common case of sorting an array of pointers, Daniel
Wagner recently modified the library sort() to use a specific swap
function for size==8, in addition to the size==4 case which was
already handled. Since sizeof(long) is either 4 or 8,
ftrace_swap_ips() is redundant and we can just let sort() pick an
appropriate and fast swap callback.

Link: http://lkml.kernel.org/r/1441834023-13130-1-git-send-email-linux@rasmusvillemoes.dkSigned-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The sleep-time and graph-time options are only for the function graph tracer
and are not used by anything else. As tracer options are now visible when
the tracer is not activated, its better to move the function graph specific
tracer options into the function graph tracer.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Commit 4104d326 ("ftrace: Remove global function list and call function
directly") simplified the ftrace code by removing the global_ops list with a
new design. But this cleanup also broke the filtering of PIDs that are added
to the set_ftrace_pid file.

Add back the proper hooks to have pid filtering working once again.

Cc: stable@vger.kernel.org # 3.16+
Reported-by: NMatt Fleming <matt@console-pimps.org>
Reported-by: NRichard Weinberger <richard.weinberger@gmail.com>
Tested-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

This patch extends tracing_thresh functionality to function profile tracer.
If tracing_thresh is set, print those entries only,
whose average is > tracing thresh.

Link: http://lkml.kernel.org/r/1434972488-8571-1-git-send-email-umesh.t@samsung.comSigned-off-by: NUmesh Tiwari <umesh.t@samsung.com>
[ Removed unnecessary 'moved' comment ]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Dynamically allocated trampolines call ftrace_ops_get_func to get the
function which they should call. For dynamic fops (FTRACE_OPS_FL_DYNAMIC
flag is set) ftrace_ops_list_func is always returned. This is reasonable
for static trampolines but goes against the main advantage of dynamic
ones, that is avoidance of going through the list of all registered
callbacks for functions that are only being traced by a single callback.

We can fix it by returning ops->func (or recursion safe version) from
ftrace_ops_get_func whenever it is possible for dynamic trampolines.

Note that dynamic trampolines are not allowed for dynamic fops if
CONFIG_PREEMPT=y.

Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1501291023000.25445@pobox.suse.cz
Link: http://lkml.kernel.org/r/1424357773-13536-1-git-send-email-mbenes@suse.czReported-by: NMiroslav Benes <mbenes@suse.cz>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.

That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().

Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.

The problem could be seen by the following commands:

 # echo 0 > /proc/sys/kernel/ftrace_enabled
 # echo function > /sys/kernel/debug/tracing/current_tracer
 # echo 1 > /proc/sys/kernel/ftrace_enabled
 # cat /sys/kernel/debug/tracing/trace

The trace will show that function tracing was not active.

Cc: stable@vger.kernel.org # 2.6.27+
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().

Consider the following situation.

 # echo 0 > /proc/sys/kernel/ftrace_enabled

After this ftrace_enabled = 0.

 # echo function_graph > /sys/kernel/debug/tracing/current_tracer

Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.

 # echo 1 > /proc/sys/kernel/ftrace_enabled

Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.

Further if we execute the following after this:
  # echo nop > /sys/kernel/debug/tracing/current_tracer

Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.

On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.

Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.

Link: http://lkml.kernel.org/r/e4fbe64cdac0dd0e86a3bf914b0f83c0b419f146.1425666454.git.panand@redhat.com

Cc: stable@vger.kernel.org # 2.6.31+
Signed-off-by: NPratyush Anand <panand@redhat.com>
[
  removed extra if (ftrace_start_up) and defined ftrace_graph_active as 0
  if CONFIG_FUNCTION_GRAPH_TRACER is not set.
]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.

ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).

When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.

For example, the following will cause ftrace to crash:

 # echo function_graph > /sys/kernel/debug/tracing/current_tracer
 # echo 0 > /proc/sys/kernel/ftrace_enabled
 # echo nop > /sys/kernel/debug/tracing/current_tracer
 # echo 1 > /proc/sys/kernel/ftrace_enabled
 # echo function_graph > /sys/kernel/debug/tracing/current_tracer

As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.

Cc: stable@vger.kernel.org # 3.17+
Reported-by: NPratyush Anand <panand@redhat.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

debugfs was fine for the tracing facility as a quick way to get
an interface. Now that tracing has matured, it should separate itself
from debugfs such that it can be mounted separately without needing
to mount all of debugfs with it. That is, users resist using tracing
because it requires mounting debugfs. Having tracing have its own file
system lets users get the features of tracing without needing to bring
in the rest of the kernel's debug infrastructure.

Another reason for tracefs is that debubfs does not support mkdir.
Currently, to create instances, one does a mkdir in the tracing/instance
directory. This is implemented via a hack that forces debugfs to do
something it is not intended on doing. By converting over to tracefs, this
hack can be removed and mkdir can be properly implemented. This patch does
not address this yet, but it lays the ground work for that to be done.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

tracing_init_dentry() will soon return NULL as a valid pointer for the
top level tracing directroy. NULL can not be used as an error value.
Instead, switch to ERR_PTR() and check the return status with
IS_ERR().
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Using just the filter for checking for trampolines or regs is not enough
when updating the code against the records that represent all functions.
Both the filter hash and the notrace hash need to be checked.

To trigger this bug (using trace-cmd and perf):

 # perf probe -a do_fork
 # trace-cmd start -B foo -e probe
 # trace-cmd record -p function_graph -n do_fork sleep 1

The trace-cmd record at the end clears the filter before it disables
function_graph tracing and then that causes the accounting of the
ftrace function records to become incorrect and causes ftrace to bug.

Link: http://lkml.kernel.org/r/20150114154329.358378039@goodmis.org

Cc: stable@vger.kernel.org
[ still need to switch old_hash_ops to old_ops_hash ]
Reviewed-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

As the set_ftrace_filter affects both the function tracer as well as the
function graph tracer, the ops that represent each have a shared
ftrace_ops_hash structure. This allows both to be updated when the filter
files are updated.

But if function graph is enabled and the global_ops (function tracing) ops
is not, then it is possible that the filter could be changed without the
update happening for the function graph ops. This will cause the changes
to not take place and may even cause a ftrace_bug to occur as it could mess
with the trampoline accounting.

The solution is to check if the ops uses the shared global_ops filter and
if the ops itself is not enabled, to check if there's another ops that is
enabled and also shares the global_ops filter. In that case, the
modification still needs to be executed.

Link: http://lkml.kernel.org/r/20150114154329.055980438@goodmis.org

Cc: stable@vger.kernel.org # 3.17+
Reviewed-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Introduce FTRACE_OPS_FL_IPMODIFY to avoid conflict among
ftrace users who may modify regs->ip to change the execution
path. If two or more users modify the regs->ip on the same
function entry, one of them will be broken. So they must add
IPMODIFY flag and make sure that ftrace_set_filter_ip() succeeds.

Note that ftrace doesn't allow ftrace_ops which has IPMODIFY
flag to have notrace hash, and the ftrace_ops must have a
filter hash (so that the ftrace_ops can hook only specific
entries), because it strongly depends on the address and
must be allowed for only few selected functions.

Link: http://lkml.kernel.org/r/20141121102516.11844.27829.stgit@localhost.localdomain

Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
[ fixed up some of the comments ]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Fix up a few typos in comments and convert an int into a bool in
update_traceon_count().

Link: http://lkml.kernel.org/r/546DD445.5080108@hitachi.comSuggested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Stack traces that happen from function tracing check if the address
on the stack is a __kernel_text_address(). That is, is the address
kernel code. This calls core_kernel_text() which returns true
if the address is part of the builtin kernel code. It also calls
is_module_text_address() which returns true if the address belongs
to module code.

But what is missing is ftrace dynamically allocated trampolines.
These trampolines are allocated for individual ftrace_ops that
call the ftrace_ops callback functions directly. But if they do a
stack trace, the code checking the stack wont detect them as they
are neither core kernel code nor module address space.

Adding another field to ftrace_ops that also stores the size of
the trampoline assigned to it we can create a new function called
is_ftrace_trampoline() that returns true if the address is a
dynamically allocate ftrace trampoline. Note, it ignores trampolines
that are not dynamically allocated as they will return true with
the core_kernel_text() function.

Link: http://lkml.kernel.org/r/20141119034829.497125839@goodmis.org

Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Using seq_printf to print a simple string or a single character is a
lot more expensive than it needs to be, since seq_puts and seq_putc
exist.

These patches do

  seq_printf(m, s) -> seq_puts(m, s)
  seq_printf(m, "%s", s) -> seq_puts(m, s)
  seq_printf(m, "%c", c) -> seq_putc(m, c)

Subsequent patches will simplify further.

Link: http://lkml.kernel.org/r/1415479332-25944-2-git-send-email-linux@rasmusvillemoes.dkSigned-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

With the new logic, if only a single user of ftrace function hooks is
used, it will get its own trampoline assigned to it.

The problem is that the control_ops is an indirect ops that perf ops
uses. What that means is that when perf registers its ops with
register_ftrace_function(), it has the CONTROL flag set and gets added
to the control list instead of the global ftrace list. The control_ops
gets added to that instead and the mcount trampoline calls the control_ops
function. The control_ops function will iterate the control list and
call the ops functions that are attached to it.

But currently the trampoline is added to the perf ops and not the
control ops, and when ftrace tries to find a trampoline hook for it,
it fails to find one and gives the following splat:

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 10133 at kernel/trace/ftrace.c:2033 ftrace_get_addr_new+0x6f/0xc0()
 Modules linked in: [...]
 CPU: 0 PID: 10133 Comm: perf Tainted: P               3.18.0-rc1-test+ #388
 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012
  00000000000007f1 ffff8800c2643bc8 ffffffff814fca6e ffff88011ea0ed01
  0000000000000000 ffff8800c2643c08 ffffffff81041ffd 0000000000000000
  ffffffff810c388c ffffffff81a5a350 ffff880119b00000 ffffffff810001c8
 Call Trace:
  [<ffffffff814fca6e>] dump_stack+0x46/0x58
  [<ffffffff81041ffd>] warn_slowpath_common+0x81/0x9b
  [<ffffffff810c388c>] ? ftrace_get_addr_new+0x6f/0xc0
  [<ffffffff810001c8>] ? 0xffffffff810001c8
  [<ffffffff81042031>] warn_slowpath_null+0x1a/0x1c
  [<ffffffff810c388c>] ftrace_get_addr_new+0x6f/0xc0
  [<ffffffff8102e938>] ftrace_replace_code+0xd6/0x334
  [<ffffffff810c4116>] ftrace_modify_all_code+0x41/0xc5
  [<ffffffff8102eba6>] arch_ftrace_update_code+0x10/0x19
  [<ffffffff810c293c>] ftrace_run_update_code+0x21/0x42
  [<ffffffff810c298f>] ftrace_startup_enable+0x32/0x34
  [<ffffffff810c3049>] ftrace_startup+0x14e/0x15a
  [<ffffffff810c307c>] register_ftrace_function+0x27/0x40
  [<ffffffff810dc118>] perf_ftrace_event_register+0x3e/0xee
  [<ffffffff810dbfbe>] perf_trace_init+0x29d/0x2a9
  [<ffffffff810eb422>] perf_tp_event_init+0x27/0x3a
  [<ffffffff810f18bc>] perf_init_event+0x9e/0xed
  [<ffffffff810f1ba4>] perf_event_alloc+0x299/0x330
  [<ffffffff810f236b>] SYSC_perf_event_open+0x3ee/0x816
  [<ffffffff8115a066>] ? mntput+0x2d/0x2f
  [<ffffffff81142b00>] ? __fput+0xa7/0x1b2
  [<ffffffff81091300>] ? do_gettimeofday+0x22/0x3a
  [<ffffffff810f279c>] SyS_perf_event_open+0x9/0xb
  [<ffffffff81502a92>] system_call_fastpath+0x12/0x17
 ---[ end trace 81a53565150e4982 ]---
 Bad trampoline accounting at: ffffffff810001c8 (run_init_process+0x0/0x2d) (10000001)

Update the control_ops trampoline instead of the perf ops one.

Reported-by: lkp@01.org
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

With the introduction of the dynamic trampolines, it is useful that if
things go wrong that ftrace_bug() produces more information about what
the current state is. This can help debug issues that may arise.

Ftrace has lots of checks to make sure that the state of the system it
touchs is exactly what it expects it to be. When it detects an abnormality
it calls ftrace_bug() and disables itself to prevent any further damage.
It is crucial that ftrace_bug() produces sufficient information that
can be used to debug the situation.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NBorislav Petkov <bp@suse.de>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When the static ftrace_ops (like function tracer) enables tracing, and it
is the only callback that is referencing a function, a trampoline is
dynamically allocated to the function that calls the callback directly
instead of calling a loop function that iterates over all the registered
ftrace ops (if more than one ops is registered).

But when it comes to dynamically allocated ftrace_ops, where they may be
freed, on a CONFIG_PREEMPT kernel there's no way to know when it is safe
to free the trampoline. If a task was preempted while executing on the
trampoline, there's currently no way to know when it will be off that
trampoline.

But this is not true when it comes to !CONFIG_PREEMPT. The current method
of calling schedule_on_each_cpu() will force tasks off the trampoline,
becaues they can not schedule while on it (kernel preemption is not
configured). That means it is safe to free a dynamically allocated
ftrace ops trampoline when CONFIG_PREEMPT is not configured.

Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NBorislav Petkov <bp@suse.de>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The file /sys/kernel/debug/tracing/eneabled_functions is used to debug
ftrace function hooks. Add to the output what function is being called
by the trampoline if the arch supports it.

Add support for this feature in x86_64.

Cc: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The current method of handling multiple function callbacks is to register
a list function callback that calls all the other callbacks based on
their hash tables and compare it to the function that the callback was
called on. But this is very inefficient.

For example, if you are tracing all functions in the kernel and then
add a kprobe to a function such that the kprobe uses ftrace, the
mcount trampoline will switch from calling the function trace callback
to calling the list callback that will iterate over all registered
ftrace_ops (in this case, the function tracer and the kprobes callback).
That means for every function being traced it checks the hash of the
ftrace_ops for function tracing and kprobes, even though the kprobes
is only set at a single function. The kprobes ftrace_ops is checked
for every function being traced!

Instead of calling the list function for functions that are only being
traced by a single callback, we can call a dynamically allocated
trampoline that calls the callback directly. The function graph tracer
already uses a direct call trampoline when it is being traced by itself
but it is not dynamically allocated. It's trampoline is static in the
kernel core. The infrastructure that called the function graph trampoline
can also be used to call a dynamically allocated one.

For now, only ftrace_ops that are not dynamically allocated can have
a trampoline. That is, users such as function tracer or stack tracer.
kprobes and perf allocate their ftrace_ops, and until there's a safe
way to free the trampoline, it can not be used. The dynamically allocated
ftrace_ops may, although, use the trampoline if the kernel is not
compiled with CONFIG_PREEMPT. But that will come later.
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When modifying code, ftrace has several checks to make sure things
are being done correctly. One of them is to make sure any code it
modifies is exactly what it expects it to be before it modifies it.
In order to do so with the new trampoline logic, it must be able
to find out what trampoline a function is hooked to in order to
see if the code that hooks to it is what's expected.

The logic to find the trampoline from a record (accounting descriptor
for a function that is hooked) needs to only look at the "old_hash"
of an ops that is being modified. The old_hash is the list of function
an ops is hooked to before its update. Since a record would only be
pointing to an ops that is being modified if it was already hooked
before.

Currently, it can pick a modified ops based on its new functions it
will be hooked to, and this picks the wrong trampoline and causes
the check to fail, disabling ftrace.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

ftrace: squash into ordering of ops for modification

The code that checks for trampolines when modifying function hooks
tests against a modified ops "old_hash". But the ops old_hash pointer
is not being updated before the changes are made, making it possible
to not find the right hash to the callback and possibly causing
ftrace to break in accounting and disable itself.

Have the ops set its old_hash before the modifying takes place.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When the last ftrace_ops is unregistered, all the function records should
have a zeroed flags value. Make sure that is the case when the last ftrace_ops
is unregistered.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Allowing function callbacks to declare their own trampolines requires
that each ftrace_ops that has a trampoline must have some sort of
accounting that keeps track of which ops has a trampoline attached
to a record.

The easy way to solve this was to add a "tramp_hash" that created a
hash entry for every function that a ops uses with a trampoline.
But since we can have literally tens of thousands of functions being
traced, that means we need tens of thousands of descriptors to map
the ops to the function in the hash. This is quite expensive and
can cause enabling and disabling the function graph tracer to take
some time to start and stop. It can take up to several seconds to
disable or enable all functions in the function graph tracer for this
reason.

The better approach albeit more complex, is to keep track of how ops
are being enabled and disabled, and use that along with the counting
of the number of ops attached to records, to determive what ops has
a trampoline attached to a record at enabling and disabling of
tracing.

To do this, the tramp_hash has been replaced with an old_filter_hash
and old_notrace_hash, which get the copy of the ops filter_hash and
notrace_hash respectively. The old hashes is kept until the ops has
been modified or removed and the old hashes are used with the logic
of the accounting to determine the ops that have the trampoline of
a record. The reason this has less of a footprint is due to the trick
that an "empty" hash in the filter_hash means "all functions" and
an empty hash in the notrace hash means "no functions" in the hash.

This is much more efficienct, doesn't have the delay, and takes up
much less memory, as we do not need to map all the functions but
just figure out which functions are mapped at the time it is
enabled or disabled.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Add three new flags for ftrace_ops:

  FTRACE_OPS_FL_ADDING
  FTRACE_OPS_FL_REMOVING
  FTRACE_OPS_FL_MODIFYING

These will be set for the ftrace_ops when they are first added
to the function tracing, being removed from function tracing
or just having their functions changed from function tracing,
respectively.

This will be needed to remove the tramp_hash, which can grow quite
big. The tramp_hash is used to note what functions a ftrace_ops
is using a trampoline for. Denoting which ftrace_ops is being
modified, will allow us to use the ftrace_ops hashes themselves,
which are much smaller as they have a global flag to denote if
a ftrace_ops is tracing all functions, as well as a notrace hash
if the ftrace_ops is tracing all but a few. The tramp_hash just
creates a hash item for every function, which can go into the 10s
of thousands if all functions are using the ftrace_ops trampoline.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When dumping the enabled_functions, use the first op that is
found with a trampoline to the record, as there should only be
one, as only one ops can be registered to a function that has
a trampoline.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

ftrace_hash_move() currently frees the old hash that is passed to it
after replacing the pointer with the new hash. Instead of having the
function do that chore, have the caller perform the free.

This lets the ftrace_hash_move() be used a bit more freely, which
is needed for changing the way the trampoline logic is done.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The clean up that adds the helper function ftrace_ops_get_func()
caused the default function to not change when DYNAMIC_FTRACE was not
set and no ftrace_ops were registered. Although static tracing is
not very useful (not having DYNAMIC_FTRACE set), it is still supported
and we don't want to break it.

Clean up the if statement even more to specifically have the default
function call ftrace_stub when no ftrace_ops are registered. This
fixes the small bug for static tracing as well as makes the code a
bit more understandable.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>