This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds support for setting up the board power from the
device tree on the U300. We use a board-specific node in the
device tree for the S365 board and bind a regulator for the
board power to this node.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the COH 901 331 RTC to the U300 device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the COH 901 327 watchdog to the U300 device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the two I2C busses to the device tree so these
probe properly.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This register the most basic peripherals and makes the
U300 boot to prompt from a device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds device tree support for the U300 timer, by making
the memory base offset and IRQ dynamically assigned, then
optionally looking them up from the device tree.

Since the timer needs to be registered before any platform
devices are created, we will go into the device tree and look
up the "/timer@c0014000" node and read our base address and
IRQ from there.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The U300 can support timer-based delays, so implement this.
Skips past jiffy calibration.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.

This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: NInderpal Singh <inderpal.singh@linaro.org>
Tested-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

arch/arm/mach-ux500/board-mop500.c: In function ‘mop500_prox_activate’:
arch/arm/mach-ux500/board-mop500.c:406:18: warning: ignoring return value of
        ‘regulator_enable’, declared with attribute warn_unused_result
        [-Wunused-result]
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Fix db8500_read_soc_id() to read all five soc_id number locations
instead of repeating the second one two times.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Trivial patch, adding the i2c Cypress trackpad used on Snow.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>

Since commit 657eee7d (media: coda: use genalloc API) the following build
error happens with imx_v4_v5_defconfig:

drivers/built-in.o: In function 'coda_remove':
clk-composite.c:(.text+0x112180): undefined reference to 'gen_pool_free'
drivers/built-in.o: In function 'coda_probe':
clk-composite.c:(.text+0x112310): undefined reference to 'of_get_named_gen_pool'
clk-composite.c:(.text+0x1123f4): undefined reference to 'gen_pool_alloc'
clk-composite.c:(.text+0x11240c): undefined reference to 'gen_pool_virt_to_phys'
clk-composite.c:(.text+0x112458): undefined reference to 'dev_get_gen_pool'

Select GENERIC_ALLOCATOR and get rid of the custom IRAM_ALLOC.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit bca7a5a0 (ARM: cpu hotplug: remove majority of cache flushing
from platforms) removes include of <asm/cacheflush.h> and hence
discovers a few indirect inclusion and declaration problems as below.

  CC      arch/arm/mach-imx/hotplug.o
In file included from arch/arm/mach-imx/hotplug.c:16:0:
arch/arm/mach-imx/common.h:100:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/common.h:100:29: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/arm/mach-imx/common.h:101:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_die’:
arch/arm/mach-imx/hotplug.c:53:2: error: implicit declaration of function ‘cpu_do_idle’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_kill’:
arch/arm/mach-imx/hotplug.c:58:26: error: ‘jiffies’ undeclared (first use in this function)
arch/arm/mach-imx/hotplug.c:58:26: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-imx/hotplug.c:58:2: error: implicit declaration of function ‘msecs_to_jiffies’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c:61:3: error: implicit declaration of function ‘time_after’ [-Werror=implicit-function-declaration]

Fix them by adding the needed inclusion and declaration.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi).  Move the phy declaration to the dts
files.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 6770b211 (ARM: OMAP2+: Export SoC information to userspace)
had some broken return value handling as noted by Russell King:

+       soc_dev = soc_device_register(soc_dev_attr);
+       if (IS_ERR_OR_NULL(soc_dev)) {
+               kfree(soc_dev_attr);
+               return;
+       }
+
+       parent = soc_device_to_device(soc_dev);
+       if (!IS_ERR_OR_NULL(parent))
+               device_create_file(parent, &omap_soc_attr);

This is nonsense.  For the first, IS_ERR() is sufficient.  For the second,
tell me what error checking is required in the return value of this
function:

struct device *soc_device_to_device(struct soc_device *soc_dev)
{
        return &soc_dev->dev;
}

when you've already determined that the passed soc_dev is a valid pointer.
If you read the comments against the prototype:

/**
 * soc_device_to_device - helper function to fetch struct device
 * @soc: Previously registered SoC device container
 */
struct device *soc_device_to_device(struct soc_device *soc);

if "soc" is valid, it means the "previously registered SoC device container"
must have succeeded and that can only happen if the struct device has been
registered.  Ergo, there will always be a valid struct device pointer for
any registered SoC device container.  Therefore, if soc_device_register()
succeeds, then the return value from soc_device_to_device() will always be
valid and no error checking of it is required.

Simples.  The rule as ever applies here: get to know the APIs your using
and don't fumble around in the dark hoping that you'll get this stuff
right.

Fix it as noted by Russell.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add GPMC data node to AM33XX device tree file.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit d16fb25d (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit 3027e267 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Boards supported upstream all use TWL6040 as audio codec, enable the common
ASoC machine driver by default for them.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for chip id detection of AM335x PG2.1 Silicon.

Currently omap3xxx_check_revision() detects PG1.0 and PG2.0 only,
this patch extends it by adding PG2.1 Si support.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds GPIO pins found on AM/DM37x.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the missing iounmap() before return from omap1_system_dma_init()
in the error handling case.
Also removed platform_device_del() on add resources error case which
cause dup device delete.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.

The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole.   Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.

The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.

Fix the issue by moving the touchscreen before the panel in the SPI
device list.

The patch fixes the following failure:

[    1.260955] acx565akm spi1.2: invalid display ID
[    1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[    1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.

Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).

This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.

Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I badly screwed up the merge in commit 6fa52ed3 ("Merge tag
'drivers-for-linus' of git://git.kernel.org/pub/.../arm-soc") by
incorrectly taking the arch/arm/mach-omap2/* data fully from the merge
target because the 'drivers-for-linus' branch seemed to be a proper
superset of the duplicate ARM commits.

That was bogus: commit ff931c82 ("ARM: OMAP: clocks: Delay clk inits
atleast until slab is initialized") only existed in head, and the
changes to arch/arm/mach-omap2/timer.c from that commit got list.

Re-doing the merge more carefully, I do think this part was the only
thing I screwed up.  Knock wood.
Reported-by: NTony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-msm/last_radio_log.c: In function 'msm_init_last_radio_log':
arch/arm/mach-msm/last_radio_log.c:69:7: error: dereferencing pointer to incomplete type

arch/cris/kernel/profile.c: In function 'init_cris_profile':
arch/cris/kernel/profile.c:79:8: error: dereferencing pointer to incomplete type

Use proc_set_size(), cfr. commit 271a15ea
("proc: Supply PDE attribute setting accessor functions")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

After the device names are created using PLATFORM_DEVID_AUTO, the old
device names given in usb_bind_phy are no longer valid causing the musb
controller not to get the phy reference. Updated the usb_bind_phy with
the new device names to get MUSB functional in omap4 panda.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like the timer.c fixes in commit ff931c82 (ARM: OMAP: clocks:
Delay clk inits atleast until slab is initialized) got lost in a
merge with da4a686a (ARM: smp_twd: convert to use CLKSRC_OF init).

Without the omap_clk_init() calls none of OMAP family of devices
boot.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments to describe merge error]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Commit 8a6201b9 (ARM: OMAP2+: Fix unmet direct dependencies for zoom
for 8250 serial) fixed unmet direct dependencies for 8250, but failed
to do the same for omap serial. This can cause the following warning:

warning: (ARCH_OMAP2PLUS_TYPICAL) selects SERIAL_OMAP which has
unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS &&
ARCH_OMAP2PLUS).

We should not select drivers, they should be selected by the
user. Fix the issue by removing the select and adding them to
omap2plus_defconfig instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

We are probably selecting more drivers than we should in ux500,
but cleaning up that logic for good can be left for another
time. Most of these could be converted into silent options in
the future, since they are always enabled on ux500 and never
needed elsewhere.

As a fixup for 3.10, let's at least select the dependencies for
the other drivers we already select, to make it consistent.

warning: (UX500_SOC_COMMON) selects AB8500_CORE which has unmet direct dependencies (HAS_IOMEM && GENERIC_HARDIRQS && ABX500_CORE && MFD_DB8500_PRCMU)
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Like all other platforms, we can only select SMP_ON_UP if SMP
is also enabled.

warning: (SOC_IMX31 && SOC_IMX35 && ARCH_MARCO) selects
 SMP_ON_UP which has unmet direct dependencies (SMP && !XIP_KERNEL)

Cc: Barry Song <baohua.song@csr.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

If the cache controller implementation is disabled at build time,
we must not call any functions related to it.

arch/arm/mach-spear/built-in.o: In function `spear13xx_l2x0_init':
arch/arm/mach-spear/spear13xx.c:47: undefined reference to `l2x0_init'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NViresh Kumar <viresh.linux@gmail.com>

The ARM CPU suspend function has its own configuration symbol,
which we need to use for conditionalizing any code calling into
it as well.

arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
/git/arm-soc/arch/arm/mach-imx/headsmp.S:57: undefined
 reference to `cpu_resume'

Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>