Add some safe values for over heat and over voltage. The Trats2 uses
3.8 V battery and during testing it operated properly under 4.48 V.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch sets display clock correctly. If Display clock isn't set
correctly then you would find below messages and Display controller
doesn't work correctly.

 exynos-drm: No connectors reported connected with modes
 [drm] Cannot find any crtc or sizes - going 1024x768

Fixes: abc0b144 ("drm: Perform basic sanity checks on probed modes")
Cc: <stable@vger.kernel.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Extend the S3C RTC node with rtc_src clock so it could be operational.
The rtc_src clock is provided by MAX77686 (Trats2) or S2MPS11 (Arndale
Octa).
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Presented patch aims to move data necessary for correct CPU cooling device
configuration from exynos_tmu_data.c to device tree.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch add dt node for PPMU_{DMC0|DMC1|LEFTBUS|RIGHTBUS} for
exynos4412-trats2 board. Each PPMU dt node includes one event of
'PPMU Count3'.

Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch add WM1811 audio codec, I2S interface and the sound
machine nodes to enable audio on exynos4412-trats2 board.
Signed-off-by: NInha Song <ideal.song@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

In order to get exact 24MHz clock frequency value for the camera
sensor and avoid rounding errors the parent clock must be CLK_XUSBXTI,
not CLK_MOUT_MPLL_USER_T.  Currently the sensor's master clock
frequency is too high and the sensor doesn't work properly.

This fixes commit 0357a443
("ARM: dts: Specify default clocks for Exynos4 camera devices").
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Add to Trats2 DTS new node for configuring the max77693 charger driver.
Only the maxim,constant-microvolt differs from default value but set all
of the optional properties anyway.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Remove fixed regulators (duplicating what max77686 provides) and
add GPIO enable control to max77686 regulators.

This gives the system full control over those regulators. Previously
the state of such regulators was a mixture of what max77686 driver set
over I2C and what regulator-fixed set through GPIO.

Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows
disabling it when it is not used. Previously this regulator was always
enabled because its enable state is a OR of:
 - ENB9 GPIO (turned always on by regulator-fixed),
 - BUCK9EN field in BUCK9CTRL register (off by max77686 through I2C).
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Add suspend to RAM configuration for max77686 regulators. Some LDOs
and bucks are disabled. This reduces energy consumption during S2R,
approximately from 17 mA to 9 mA.

Additionally remove old and not supported bindings:
 - regulator-mem-off
 - regulator-mem-idle
 - regulator-mem-on
The max77686 driver does not parse them and they are not documented
anywere.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Add node for fuel gauge present in Maxim 77693 PMIC. This allows control
over battery charging state on Trats2 board.

The fuel gauge is compatible with max17042 battery driver (Maxim
17042/17047/17050).  Although datasheet rev 2.2 for MAX77693 describes
fuel gauge as Maxim 17042-like, the chip on Trats2 board identifies
itself as Maxim 17047-like.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds stdout-path property to chosen nodes of Exynos4 boards
to enable use of earlycon feature without the need to hardcode port
number in kernel itself.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All currently supported boards use hsotg/dwc2 controller in device
('peripheral') mode, so add property which sets correct operation mode.
This patch fixes support in recent changes in dwc2 driver, which added
support for dual-role devices.
Suggested-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds max77693-haptic node to support for haptic motor driver.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add PWM(Pulse Width Modulation) node and
handle to use pwm property.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Specify the default mux and divider clocks in device tree
to ensure the FIMC devices on Trats, Trats2, Universal_c210
and Odroid X2/U3 boards are clocked from recommended clock
source and with maximum supported frequency.
For Trats2 also the MIPI-CSIS and the camera sensor clocks
are configured, the 'clock-frequency' property is deprecated
in favour of 'assigned-clock-rates' property.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch enables support for TMU at Exynos4412 based Trats2 board.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add SDHCI node for supporting the micro SD card. On Trats2 board the
SDHCI does not use sd2_cd pins (gpk2-2) for card detect but gpx3-4
instead.

Power is supplied from LDO21 regulator which in off state is controlled
by external GPIO pin.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The MAX77693 is a companion power management IC for smart phones and
tablets.

The MAX77693 contains input over-voltage protection (OVP),
a fully-integrated 2.5A switching charger for Lithium Ion battery with
integrated battery disconnect, OTG/accessory 5V output power,
a high-current white LED driver for camera flash, two safeout LDOs,
a haptic motor driver, Model Gauge m3 battery fuel gauge and MicroUSB
Interface Controller (MUIC). I2C serial interface is used for
communicating.

Add MAX77693 node to the Trats2 board. This allows using:
 - charger regulator,
 - 2 safeout LDO regulators (for USB OTG),
 - extcon.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds sleep mode pin configuration using pin control hog
mechanism to configure states of GPIO pins in sleep mode. This is
required to reduce leakage current in sleep mode and prevent glitching
of components on the board.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In MAX77686 PMIC two regulators dedicated for eMMC memory can be
controlled both by I2C interface and a GPIO pin, with the resulting
regulator state being a logical OR of both. Since the GPIO control is
used both by the kernel and the lowest level bootloader at reset, the
regulator should be disabled by I2C control to allow it to be turned off
by GPIO control.

This patch removes regulator-always-on properties from both regulators
and, while at it, also unsupported regulator-mem-off.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTushar Behera <trblinux@gmail.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch replaces the "cs-gpio" from "controller-data" node
as was specified in the old binding and uses the standard
"cs-gpios" property expected by the SPI core as is defined now
in the spi-s3c64xx driver DT binding.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch enables exynos_usbphy and hsotg device nodes.

Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NChanho Park <chanho61.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch fixed gpio key device node.
First, fix incorrect gpio property.
And then, add ok-key node where locate bottom center.
I have tested on exynos4412-trats2 board.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Exynos4412-trats2 board have light/proximity sensor.
This patch add cm36651 light/ proximity sensor node for exynos4412.
cm36651 is required properties as below.
- Use i2c-gpio for cm36651 sensor.
- Use fixed regulator for the IR LED.
  It is a part of the cm36651 for proximity detection.
- cm36651 is i2c device driver so need to use i2c-gpio driver.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch fixed incorrect compatible for ak8975 magnetic sensor.
ak8975 magnetic sensor use compatible "ak8975" or "asahi-kasei,ak8975"
In this patch, use "asahi-kasei,ak8975" according to dt bindings document.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch enables the rear facing camera (s5c73m3) on TRATS2 board
by adding the I2C0 bus controller, s5c73m3 sensor, MIPI CSI-2 receiver
and the sensor's voltage regulator supply nodes.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Remove unused /camera/clock-controller node and add required clock
properties to the camera node. This is required for a clock provider
that will be referenced by image sensor devices.
Also add required clock related changes to s5k6a3 device node and
afvdd regulator supply.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The i2c_ak8975 controller uses label i2c8.
This alias is already used for I2C controller 8 defined
in file arch/arm/boot/dts/exynos4.dtsi.

This patch renames a label for i2c_ak8975 to i2c9.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats2.
It adds also trats2 specific properties for DSI
and regulator required by panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Add generic compatible strings to the respective board DT files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch use ADC to get the temperature of SoC/battery by using NTC thermistor
driver in hwmon. NTC thermistor driver covnvert ADC's raw data to temperature
by using following variables:
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds a label and #clock-cells property to device node of
max77686 PMIC to allow using it as a clock provider.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch removes device tree node of SDHCI0 controller and replaces
it with MSHC to enable support MMC 4.4 and improve performance of eMMC
memory.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add dts entries required for the SPI bus used for
firware upload by the S5C73M3 camera.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch enables the front camera using the internal
camera ISP (FIMC-IS).
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds AK8975 magnetometer node and corresponding
i2c-gpio bus node for TRATS2 board.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>