Before this work, TX timestamping is done by sending each SKB to the MC.
On the 8000 series (Medford1) we have high speed timestamping via the
 MAC, which means we can use normal TX queues for this without a
 significant drop in bandwidth.  On the X2000 series (Medford2) support
 for transmitting via the MC is removed, so the new way must be used.

This patch enables timestamping on a TX queue, if requested.
It also enhances TX event handling to process the extra completion events,
 and puts the time in the SKB.
Signed-off-by: NMartin Habets <mhabets@solarflare.com>
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NAPI budget is only for RX processing work, not other work such as
 TX or MCDI completion handling.
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.
Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@gmail.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.

This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.

This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.

However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.

Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.

This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.

Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.

Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().

This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a VF is under PF VLAN assignment:

ip link set <pf> vf <#> vlan <vid>

This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":

failed to kill vid 0081/<vid> for device <vf>

This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.

Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.

The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.

However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes the following sparse warning:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c:46:27: warning:
 symbol 'pedits' was not declared. Should it be static?

Fixes: 27ece1f3 ("cxgb4: add tc flower support for ETH-DMAC rewrite")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.

To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.

In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bit TPD3[31] is used as a timestamp bit if PTP is enabled, but
it's used as an address bit if PTP is disabled.  Since PTP isn't
supported by the driver, we can extend the DMA address to 46 bits.
Signed-off-by: NWang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Doing a bitwise AND between a bool and an int is generally not a good idea.
The bool will be promoted to an int with value 0 or 1,
the int is generally regarded as true with a non-zero value,
thus ANDing them has the potential to yield an undesired result.

This commit fixes the following smatch warnings:

drivers/net/ethernet/stmicro/stmmac/enh_desc.c:344 enh_desc_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:337 dwmac4_rd_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:380 dwmac4_rd_prepare_tso_tx_desc() warn: maybe use && instead of &
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.

Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"

Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: NDaniel Hua <daniel.hua@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon
hotplugging my kernel would immediately crash due to igb:

[  680.825801] kernel BUG at drivers/pci/msi.c:352!
[  680.828388] invalid opcode: 0000 [#1] SMP
[  680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb]
[  680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G           O     4.15.0-rc3Lyude-Test+ #6
[  680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017
[  680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn
[  680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0
[  680.833271] RSP: 0018:ffffc9000030fbf0 EFLAGS: 00010286
[  680.833761] RAX: ffff8803405f9c00 RBX: ffff88033e3d2e40 RCX: 000000000000002c
[  680.834278] RDX: 0000000000000000 RSI: 00000000000000ac RDI: ffff880340be2178
[  680.834832] RBP: 0000000000000000 R08: ffff880340be1ff0 R09: ffff8803405f9c00
[  680.835342] R10: 0000000000000000 R11: 0000000000000040 R12: ffff88033d63a298
[  680.835822] R13: ffff88033d63a000 R14: 0000000000000060 R15: ffff880341959000
[  680.836332] FS:  0000000000000000(0000) GS:ffff88034f440000(0000) knlGS:0000000000000000
[  680.836817] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  680.837360] CR2: 000055e64044afdf CR3: 0000000001c09002 CR4: 00000000003606e0
[  680.837954] Call Trace:
[  680.838853]  pci_disable_msix+0xce/0xf0
[  680.839616]  igb_reset_interrupt_capability+0x5d/0x60 [igb]
[  680.840278]  igb_remove+0x9d/0x110 [igb]
[  680.840764]  pci_device_remove+0x36/0xb0
[  680.841279]  device_release_driver_internal+0x157/0x220
[  680.841739]  pci_stop_bus_device+0x7d/0xa0
[  680.842255]  pci_stop_bus_device+0x2b/0xa0
[  680.842722]  pci_stop_bus_device+0x3d/0xa0
[  680.843189]  pci_stop_and_remove_bus_device+0xe/0x20
[  680.843627]  trim_stale_devices+0xf3/0x140
[  680.844086]  trim_stale_devices+0x94/0x140
[  680.844532]  trim_stale_devices+0xa6/0x140
[  680.845031]  ? get_slot_status+0x90/0xc0
[  680.845536]  acpiphp_check_bridge.part.5+0xfe/0x140
[  680.846021]  acpiphp_hotplug_notify+0x175/0x200
[  680.846581]  ? free_bridge+0x100/0x100
[  680.847113]  acpi_device_hotplug+0x8a/0x490
[  680.847535]  acpi_hotplug_work_fn+0x1a/0x30
[  680.848076]  process_one_work+0x182/0x3a0
[  680.848543]  worker_thread+0x2e/0x380
[  680.848963]  ? process_one_work+0x3a0/0x3a0
[  680.849373]  kthread+0x111/0x130
[  680.849776]  ? kthread_create_worker_on_cpu+0x50/0x50
[  680.850188]  ret_from_fork+0x1f/0x30
[  680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b
[  680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP: ffffc9000030fbf0

As it turns out, normally the freeing of IRQs that would fix this is called
inside of the scope of __igb_close(). However, since the device is
already gone by the point we try to unregister the netdevice from the
driver due to a hotplug we end up seeing that the netif isn't present
and thus, forget to free any of the device IRQs.

So: make sure that if we're in the process of dismantling the netdev, we
always allow __igb_close() to be called so that IRQs may be freed
normally. Additionally, only allow igb_close() to be called from
__igb_close() if it hasn't already been called for the given adapter.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Fixes: 9474933c ("igb: close/suspend race in netif_device_detach")
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable@vger.kernel.org
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.
Signed-off-by: NMatt Turner <matt.turner@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By design, the idleslope increments are restricted to 16.384kbps steps.
Add a comment to igb_main.c making that explicit and add one example
that illustrates the impact of that.
Signed-off-by: NJesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:

    "HTHRESH should be given a non zero value when ever PTHRESH is
     used."

In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: NMatt Turner <matt.turner@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done.  Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.

The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".

Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.

To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.

This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.

Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: NCorinna Vinschen <vinschen@redhat.com>
Tested-by: NAaron Brown <arron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.

Simply remove the error message and gracefully accept such events.

Fixes: c723c735 ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

memset variables to 0 to fix sparse warnings:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:409:42: sparse: Using
plain integer as NULL pointer

drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:43:47: sparse: Using
plain integer as NULL pointer

Fixes: ad75b7d3 ("cxgb4: implement ethtool dump data operations")
Fixes: 91c1953d ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:39:5: error:
redefinition of 'cudbg_compress_buff'
    int cudbg_compress_buff(struct cudbg_init *pdbg_init,
        ^~~~~~~~~~~~~~~~~~~
   In file included from
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:23:0:
   drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.h:45:19: note: previous
definition of 'cudbg_compress_buff' was here
    static inline int cudbg_compress_buff(struct cudbg_init *pdbg_init,
                      ^~~~~~~~~~~~~~~~~~~

Fixes: 91c1953d ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang.  This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.

Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.

If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.

This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.

The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts.  By triggering a SW
interrupt, interrupts are forced on.  If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.

This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: NMichal Kuchta <michal.kuchta@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>