Signed-off-by: NRob Clark <robdclark@gmail.com>

Both MDP4 and MDP5 share some code as far as YUV support is
concerned. This change adds this information and will be followed
by the actual MDP4 and MDP5 YUV support patches.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

If crtc <-> encoder linkage changes, we could end up with the CRTC
listening for the wrong error or vsync irqs.  Generally this problem
would correct itself relatively quickly, since we update the global
irqmask after dispatching irqs, but to be sure let the CRTC trigger
update_irq().
Signed-off-by: NRob Clark <robdclark@gmail.com>

We'll want basically the same thing for mdp5, so refactor it out so it
can be shared.
Signed-off-by: NRob Clark <robdclark@gmail.com>

This can be shared between mdp4 and mdp5.  Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Add initial support for a3xx 3d core.

So far, with hardware that I've seen to date, we can have:
 + zero, one, or two z180 2d cores
 + a3xx or a2xx 3d core, which share a common CP (the firmware
   for the CP seems to implement some different PM4 packet types
   but the basics of cmdstream submission are the same)

Which means that the eventual complete "class" hierarchy, once
support for all past and present hw is in place, becomes:
 + msm_gpu
   + adreno_gpu
     + a3xx_gpu
     + a2xx_gpu
   + z180_gpu

This commit splits out the parts that will eventually be common
between a2xx/a3xx into adreno_gpu, and the parts that are even
common to z180 into msm_gpu.

Note that there is no cmdstream validation required.  All memory access
from the GPU is via IOMMU/MMU.  So as long as you don't map silly things
to the GPU, there isn't much damage that the GPU can do.
Signed-off-by: NRob Clark <robdclark@gmail.com>

The snapdragon chips have multiple different display controllers,
depending on which chip variant/version.  (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.)  And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.

To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.

The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently.  But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge.  This
would remove the 'msm_connector' base class.  But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..

This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: NRob Clark <robdclark@gmail.com>

A simple DRM/KMS driver for the TI LCD Controller found in various
smaller TI parts (AM33xx, OMAPL138, etc).  This driver uses the
CMA helpers.  Currently only the TFP410 DVI encoder is supported
(tested with beaglebone + DVI cape).  There are also various LCD
displays, for which support can be added (as I get hw to test on),
and an external i2c HDMI encoder found on some boards.

The display controller supports a single CRTC.  And the encoder+
connector are split out into sub-devices.  Depending on which LCD
or external encoder is actually present, the appropriate output
module(s) will be loaded.

v1: original
v2: fix fb refcnting and few other cleanups
v3: get +/- vsync/hsync from timings rather than panel-info, add
    option DT max-bandwidth field so driver doesn't attempt to
    pick a display mode with too high memory bandwidth, and other
    small cleanups
v4: remove some unneeded stuff from panel-info struct, properly
    set high bits for hfp/hsw/hbp for rev 2, add DT bindings docs
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: NKoen Kooi <koen@dominion.thruhere.net>

Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.

Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.

Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.

This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.

Thanks to Tomi and Sricharan for some additional testing.
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NR, Sricharan <r.sricharan@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
 cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>