MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Oprofile support for PA6T, kernel side.

Also rename the PA6T_SPRN.* defines to SPRN_PA6T.*.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Minor HID change. Firmware can't know that we want this set so we have
to set it in the kernel.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Device 0 function 0 on the root bus is really a two-function bus agent,
but only the first function is visible. Because of this, we need to
allow config accesses into the second range. Modify the check for valid
offsets accordingly.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

PowerPC 750CL has high BATs.  The patch below adds a CPU_FTRS_750CL that
includes that.  Without it, the original firmware mappings in the high BATs
aren't cleared which continue to override the linux translations.

It also adds CPU_FTR_COMMON to CPU_FTRS_750GX for completeness.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

These got added recently.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Sync with the Kconfig changes, and enable some options for celleb

Cc: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJens Osterkamp <jens@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Enable Periodic Recalibration (PTCAL) support for Cell XDR memory,
using the new ibm,cbe-start-ptcal and ibm,cbe-stop-ptcal RTAS calls.

Tested on QS20 and QS21 (by Thomas Huth). It seems that SLOF has
problems disabling, at least on QS20; this patch should only be
used once these problems have been addressed.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This patch adds support for a proper device-tree.
A porper device-tree on cell contains be nodes
for each CBE containg nodes for SPEs and all the
other special devices on it.
Ofcourse oldschool devicetree is still supported.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

The of_iomap function maps memory for a given
device_node and returns a pointer to that memory.
This is used at some places, so it makes sense to
a seperate function.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

At the moment the pmi device driver is probing for devices with
a given type and a given name. As there may be devices of
the same type but with a different name, probing should be
done also for device type only.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This patch adds a check for the private driver data to be initialized.
The bug showed up, as the caller found a pmi device by it's type.
Whereas the pmi driver probes for the type and the name.
Since the name was not as the driver expected, it did not initialize.
A more relaxed probing will be supplied with an extra patch, too.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

The new PMI driver was added in order to support
cpufreq on blades that require the frequency to
be controlled by the service processor, so use it
on those.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This patch adds some attributes the cpu and spu nodes:
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_begin
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_end
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_full_stop
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This patch introduces a little function for transforming
register values into temperature.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This change fixes the case where spu_base and spufs are initialised on a
system with no SPEs - unconditionally create the spu_lists so spu_alloc
doesn't explode, and check for spu_management ops before starting spufs.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

 arch/powerpc/platforms/cell/spu_base.c    |    7 ++++---
 arch/powerpc/platforms/cell/spufs/inode.c |    5 +++++
 2 files changed, 9 insertions(+), 3 deletions(-)

spu_base.c is always built into the kernel image, so there is no need
for a cleanup function.  And some of the things it does are in the
way for my following patches, so I'd rather get rid of it ASAP.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

 - remove the spu_acquire_runnable from spu_run_init.  I need to
   opencode it in spufs_run_spu in the next patch
 - remove various inline attributes, we don't really want to inline
   long functions with multiple callsites
 - cleanup return values and runcntl_write calls in spu_run_init
 - use normal kernel codingstyle in spu_reacquire_runnable
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

spu_coredump_calls.owner is NULL in case of a builtin spufs,
so the checks in here break.
Check for the availability of the spu_coredump_calls variable
instead.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Dynamically allocated read/write buffer in spufs_arch_write_note() will
not be freed. Convert it to get_free_page at the same time.

Cc: Akinobu Mita <mita@fixstars.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Change the loop in spu_wait to be a little more straightforward.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Add a 'mode=' option to spufs mount arguments. This allows more
control over access to the top-level spufs directory.

Tested on Cell.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

GCC may generates inline copy loop to handle memcpy() function
instead of kernel defined memcpy(). But this inlined version of memcpy()
causes an alignment interrupt when copying from local store.

This patch uses memcpy_fromio() and memcpy_toio to copy local store
to prevent memcpy() being inlined.
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

We now have proper locking around assignets of the mapping pointers,
and the spin_unlock implies enough of a barrier to get rid of the
explicit one.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

When SPU isolation mode enabled, isolated_loader would be
allocated by spufs_init_isolated_loader() on module_init().
But anyone do not free it.

This patch introduces spufs_exit_isolated_loader() which is
the opposite of spufs_init_isolated_loader() and called on
module_exit().

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

spufs module_init forgot to call a few cleanup functions
on error path. This patch also includes cosmetic changes in
spu_sched_init() (identation fix and return error code).

[modified by hch to apply ontop of the latest schedule changes]

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This patch checks return value of spu_acquire_runnable() in
spufs_mfc_write().
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

There is no reason for run_sema to be a struct semaphore.  Changing
it to a mutex and rename it accordingly.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

This change populates a siginfo struct for SPE application exceptions
(ie, invalid DMAs and illegal instructions).

Tested on an IBM Cell Blade.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
  page faults
- if an spu program attempts to access its own mmio
  areas through DMA, we get an immediate livelock when
  the nopage function tries to acquire the same mutex

This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.

We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

There is no reason to execute spu_init_channels under spu_mutex
after the spu has been taken off the freelist it's ours.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Addition to stop_wq needs to happen before adding to the runqeueue and
under the same lock so that we don't have a race window for a lost
wake up in the spu scheduler.
Signed-off-by: NLuke Browning <lukebrowning@us.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

For quite a while now spu state is protected by a simple mutex instead
of the old rw_semaphore, and this means we can simplify the locking
around spu_setup_isolated a lot.

Instead of doing an spu_release before entering spu_setup_isolated and
then calling the complicated spu_acquire_exclusive we can now simply
enter the function locked an in guaranteed runnable state, so that the
only bit of spu_acquire_exclusive that's left is the call to
spu_unmap_mappings.

Similarly there's no more need to unlock and reacquire the state_mutex
when spu_setup_isolated is done, but we can always return with the
lock held and only drop it in spu_run_init in the failure case.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

A single context should only be woken once, and we should not have
more wakeups for a given priority than the number of contexts on
that runqueue position.

Also add some asserts to trap future problems in this area more
easily.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

set_bit does not guarantee ordering on powerpc, so using it
for communication between threads requires explicit
mb() calls.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

To not lose a spu thread we need to make sure it always gets put back
on the runqueue.  In find_victim aswell as in the scheduler tick as done
in the previous patch.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

To not lose a spu thread we need to make sure it always gets put back
on the runqueue.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>

Make sure the pointers to various mappings are cleared once the last
user stopped using them.  This avoids accessing freed memory when
tearing down the gang directory aswell as optimizing away
pte invalidations if no one uses these.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>