Replace the references to the iwl_priv structure with the iwl_trans
structure as the priv structure is never referenced other than to
access the trans structure.  Rename from iwlagn to iwl.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting

Cc: stable@vger.kernel.org #3.0+
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ht40 setting should not change after association unless channel switch

This fix a problem we are seeing which cause uCode assert because driver
sending invalid information and make uCode confuse

Here is the firmware assert message:
kernel: iwlagn 0000:03:00.0: Microcode SW error detected.  Restarting 0x82000000.
kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301
kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump:
kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6
kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT
kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2
kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1
kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2
kernel: iwlagn 0000:03:00.0: 0x01008035 | data1
kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2
kernel: iwlagn 0000:03:00.0: 0x000005A7 | line
kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time
kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low
kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1
kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3
kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version
kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version
kernel: iwlagn 0000:03:00.0: 0x00480303 | board version
kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd
kernel: iwlagn 0000:03:00.0: CSR values:
kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
kernel: iwlagn 0000:03:00.0:        CSR_HW_IF_CONFIG_REG: 0X00480303
kernel: iwlagn 0000:03:00.0:          CSR_INT_COALESCING: 0X0000ff40
kernel: iwlagn 0000:03:00.0:                     CSR_INT: 0X00000000
kernel: iwlagn 0000:03:00.0:                CSR_INT_MASK: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_FH_INT_STATUS: 0X00000000
kernel: iwlagn 0000:03:00.0:                 CSR_GPIO_IN: 0X00000030
kernel: iwlagn 0000:03:00.0:                   CSR_RESET: 0X00000000
kernel: iwlagn 0000:03:00.0:                CSR_GP_CNTRL: 0X080403c5
kernel: iwlagn 0000:03:00.0:                  CSR_HW_REV: 0X000000b0
kernel: iwlagn 0000:03:00.0:              CSR_EEPROM_REG: 0X07d60ffd
kernel: iwlagn 0000:03:00.0:               CSR_EEPROM_GP: 0X90000001
kernel: iwlagn 0000:03:00.0:              CSR_OTP_GP_REG: 0X00030001
kernel: iwlagn 0000:03:00.0:                 CSR_GIO_REG: 0X00080044
kernel: iwlagn 0000:03:00.0:            CSR_GP_UCODE_REG: 0X000093bb
kernel: iwlagn 0000:03:00.0:           CSR_GP_DRIVER_REG: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_UCODE_DRV_GP1: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_UCODE_DRV_GP2: 0X00000000
kernel: iwlagn 0000:03:00.0:                 CSR_LED_REG: 0X00000078
kernel: iwlagn 0000:03:00.0:        CSR_DRAM_INT_TBL_REG: 0X88214dd2
kernel: iwlagn 0000:03:00.0:        CSR_GIO_CHICKEN_BITS: 0X27800200
kernel: iwlagn 0000:03:00.0:             CSR_ANA_PLL_CFG: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_HW_REV_WA_REG: 0X0001001a
kernel: iwlagn 0000:03:00.0:        CSR_DBG_HPET_MEM_REG: 0Xffff0010
kernel: iwlagn 0000:03:00.0: FH register values:
kernel: iwlagn 0000:03:00.0:         FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00
kernel: iwlagn 0000:03:00.0:        FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0
kernel: iwlagn 0000:03:00.0:                  FH_RSCSR_CHNL0_WPTR: 0X00000060
kernel: iwlagn 0000:03:00.0:         FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
kernel: iwlagn 0000:03:00.0:          FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
kernel: iwlagn 0000:03:00.0:            FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
kernel: iwlagn 0000:03:00.0:    FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
kernel: iwlagn 0000:03:00.0:                FH_TSSR_TX_STATUS_REG: 0X07ff0001
kernel: iwlagn 0000:03:00.0:                 FH_TSSR_TX_ERROR_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries
kernel: ------------[ cut here ]------------
WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407()
kernel: Hardware name: 4290W4H
kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2
kernel: Call Trace:
kernel:  [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87
kernel:  [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407
kernel:  [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32
kernel:  [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87
kernel:  [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3
kernel:  [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a
kernel:  [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel:  [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel:  [<ffffffff8104ba97>] ? kthread+0x7a/0x82
kernel:  [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10
kernel:  [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11
kernel:  [<ffffffff813d21b0>] ? gs_change+0xb/0xb

Cc: <stable@kernel.org> 3.1+
Reported-by: NUdo Steinberg <udo@hypervisor.org>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.

Cc: stable@vger.kernel.org
Reported-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not sure it is the best way to do it, but many times we want to know what the
configuration options were enabled for the compiled driver.
Let's just log the options during load time; so there were be no confusion.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes handling the calibration data more generic
and no longer requires updating IWL_CALIB_MAX when a
new uCode comes with more calibration packets. Since
we just copy the data back, there's also no need for
understanding which calibration we received -- we can
just reflect it back to the runtime uCode.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are many mac80211 callback functions in the driver, as current
implementation, those functions are scatter everywhere which is very difficult
to find and maintain, move all the mac80211 callback functions into single
file. There should be no functional changes
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Relocate the ucode files and update relevant code.
More code refactoring.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The upper layers of the driver do not need to know where the ucode is
stored.  It already passes in an enum of which ucode to load.  Let the
lower layer routines select the ucode to load.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whether to use NoA or not is entire controlled
by the uCode right now, and it also adds the
attribute to beacons. We do need to add it to
probe responses in the driver though.

Keep track of the NoA notification from the
uCode and add the data to probe responses when
such are transmitted. Use RCU to manage the
lifetime.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The iwl_alloc_all routine is only called once.  Delete the argument
and print an error in the calling routine if needed.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The WoWLAN API changed due to netdetect and
we now have a more generic "D3 configuration"
command that enables the sysassert & rfkill
wakeup triggers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move iwl_enable_rfkill_int to iwl-core.h, and remove the empty
iwl-helpers.h
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After driver split, no need to separate station management functions
in two files, merge it
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the same calling style for all the mac80211 callback functions
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add IWL_DEBUG_MAC80211 debug for all mac80211 callback function
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Once enable rts/cts for aggregation queue, do not disable until the
last aggregation queue closed.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A pointer to the bus structure is still in iwl_priv.  Finish
cleanup and remove it.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Updating the beacon every time right after one was
transmitted is pointless, most of the time we might
not even have to update it. We will update it every
time it changes, which includes from set_tim(), a
callback iwlwifi didn't implement so far.

This also reduces latency for clients, previously
we would update the beacon right after the previous
one was transmitted, and then a TIM change would
only take effect after that again -- updating the
beacon right after the TIM changes makes the TIM
change go out to the air faster.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My previous patch for init calib cfg disable a set of calibration for both
init and runtime which cause performance issue, Fix it
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename the iwlagn module as iwlwifi in preparation for future
changes.  Add an alias to iwlagn for backward compatibility.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we're associated and want to do P2P at the same
time, the scan for remain-on-channel is currently
limited to 80ms because of the way the device will
behave in that case. Instead of doing that, split
up the dwell times into little pieces. It will not
actually be a single big dwell time then, but will
be close enough. This improves robustness of P2P
in such scenarios.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the driver split there's no more need for
shared/non-shared private station data so remove
struct iwl_station_priv_common entirely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the removal of the sysfs files, it is no
longer necessary to have upper layers control
the drvdata, so let the PCI driver have it for
itself completely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debug_level and temperature files should be in
debugfs, the txpower file is completely unneeded
since TX power can be set with iw/iwconfig.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The transport callbacks might as well be undefined
when CONFIG_PM_SLEEP is not set, so ifdef all of
it out and make everything available for PM_SLEEP
only.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a wrapper in the upper layer to call the mac80211's function.
This allows not to have the transport layer call mac80211 directly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a non-empty Tx queueis freed, the buffer it contains must be
freed too. Since the Tx cmd are now allocated from a pool, the Tx
cmd must be freed too.

This patch avoids to destroy a non-empty pool of Tx cmd.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reverts commit 9b768832 which
was introduced in 2.6.38-rc1.  It works around a problem where the iwlagn
driver stimulates a bug crashing (requiring power cycle to recover) some
APs under heavy traffic.

CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
SIgned-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reaches encapsulation for this file. In order to reach this:
 * move priv->valid_context to iwl_shared
 * move the last_rejected initialization to the upper layer
 * define a wrapper iwl_nic_config in the upper layer that calls to
   cfg->lib->ops->nic_config
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Another round of clean up on the transport layer.
Define a wrapper around wiphy_rfkill_set_hw_state to prevent the
transport layer from accessing priv->hw.
Also move wait_command_queue to the transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to implement support for GO powersave on
the P2P client side, the ucode needs to know what
GO we're trying to authenticate/associate with,
it needs to have a station entry and the BSSID in
the RXON set.

Implement the new mac80211 callbacks to give this
data to the device.

Since this is also useful for the device when a
normal connection is established, also program it
with the information in that case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

priv->mac80211_registered and priv->hw needed to move to shared.
stop_queue API was added in order to allow the upper layer to stop
the SW queues for regulatory purposes.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This one is really transport related.

==== moves Stanislaw's code to BSD area ====
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This one is really transport related.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove a few dereferences of priv from the transport layer while
at it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This mapping is transport related.
This allows us to remove the notion of tx queue from the tx path in
the upper layer.
iwl_wake_any_queue moved to transport layer since it needs to access
these mappings.
The TX API is nicer now:

int (*tx)(struct iwl_trans *trans, struct sk_buff *skb,
		struct iwl_device_cmd *dev_cmd, u8 ctx, u8 sta_id);
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a near future, the upper layer won't be aware of the tx queues.
This allows to remove one place where the upper layer needed to
provide the tx queue index to the transport layer.
This also saves around 1.5MB.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the mapping tx_queue -> fifo is really transport related. The upper
layer should be involved in such things.

Note that upon agg_disable, the queue is always mapped to fifo 0, but
this doesn't matter since when the queue will be setup again for a
new BA session, it will be configured to the good fifo anyway.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we remove the module, we free all the tx and rx resources.
Before doing that, we'd better stop the tx / rx activity. Calling
iwl_trans_stop_device in iwl_remove helps also to remove a few API
functions:
 * rx_free:		happens in iwl_trans_free
 * tx_free:		happens in iwl_trans_free
 * disable_sync_irq:	happens in iwl_trans_stop_device
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>