Add dummy primary plane implementation. LCDC does not really have
planes, only simple framebuffer that is mandatory. This primary plane
implementation has the necessary checks for implementing simple
framebuffer trough DRM plane abstraction. For setting the actual
framebuffer the implementation relies on a CRTC side function.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Make tilcdc_crtc_page_flip() work if crtc is not yet on. The plane
commit sometimes comes before crtc is turned on. The new framebuffer
should be set to scanout also in that case, so that it is there when
crtc is turned on at the end of the commit phase.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Make tilcdc_crtc_page_flip() public for dummy plane implementation to use.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Fix tilcdc component master unloading. If a subcomponent module
(tda998x in this case) is unloaded before its master (tilcdc in this
case), it calls drm_put_dev() and it should not be called again by
the master when its module is unloaded. However component_master_del()
must still be called and the check if the drm_put_dev() has been
called must be in component_master_ops unbind() callback, not in
platform_driver remove() callback.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Avoid error print by of_graph_get_next_endpoint() if there is no ports
present.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Add drm_crtc_vblank_on() and *_off() calls to start() and stop()
functions, to make sure any vblank waits etc. gets properly cleaned
up.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Increase time out for waiting frame done interrupt. 50ms is long
enough for the usual display modes (50 Hz or higher refresh rate), but
it may be a bit tight for some unusual mode.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Move wait queue waiting of LCDC_FRAME_DONE IRQ from tilcdc_crtc_dpms()
into stop() function. This is just a cleanup and enables independent
use of stop() function.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Reorder the IRQ function so that the write to LCDC_END_OF_INT_IND_REG
is done last. The write to LCDC_END_OF_INT_IND_REG indicates to LCDC
that the interrupt service routine has completed (see section
13.3.6.1.6 in AM335x TRM). This is needed if LCDC's ipgvmodirq module
is configured for pulse interrupts.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Move LCDC_SYNC_LOST handling inside if (ver == 2) statement.
LCDC_SYNC_LOST interrupt status bit is only defined for version 2
silicon.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Restore old dpms state in pm_resume(). The dpms is turned off in
pm_suspend() and it should be restored to its original state in
pm_resume(). Without this patch the display is left blanked after a
suspend/resume cycle.

Fixes commit 614b3cfe ("drm/tilcdc: disable the lcd controller/dma
engine when suspend invoked")
Signed-off-by: NJyri Sarha <jsarha@ti.com>

drm_connector_register_all requires a few too many locks because our
connector_list locking is busted. Add another FIXME+hack to work
around this. This should address the below lockdep splat:

======================================================
[ INFO: possible circular locking dependency detected ]
4.7.0-rc5+ #524 Tainted: G           O
-------------------------------------------------------
kworker/u8:0/6 is trying to acquire lock:
 (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120

but task is already holding lock:
 ((fb_notifier_list).rwsem){++++.+}, at: [<ffffffff810ac195>] __blocking_notifier_call_chain+0x35/0x70

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 ((fb_notifier_list).rwsem){++++.+}:
       [<ffffffff810df611>] lock_acquire+0xb1/0x200
       [<ffffffff819a55b4>] down_write+0x44/0x80
       [<ffffffff810abf91>] blocking_notifier_chain_register+0x21/0xb0
       [<ffffffff814c7448>] fb_register_client+0x18/0x20
       [<ffffffff814c6c86>] backlight_device_register+0x136/0x260
       [<ffffffffa0127eb2>] intel_backlight_device_register+0xa2/0x160 [i915]
       [<ffffffffa00f46be>] intel_connector_register+0xe/0x10 [i915]
       [<ffffffffa0112bfb>] intel_dp_connector_register+0x1b/0x80 [i915]
       [<ffffffff8159dfea>] drm_connector_register+0x4a/0x80
       [<ffffffff8159fe44>] drm_connector_register_all+0x64/0xf0
       [<ffffffff815a2a64>] drm_modeset_register_all+0x174/0x1c0
       [<ffffffff81599b72>] drm_dev_register+0xc2/0xd0
       [<ffffffffa00621d7>] i915_driver_load+0x1547/0x2200 [i915]
       [<ffffffffa006d80f>] i915_pci_probe+0x4f/0x70 [i915]
       [<ffffffff814a2135>] local_pci_probe+0x45/0xa0
       [<ffffffff814a349b>] pci_device_probe+0xdb/0x130
       [<ffffffff815c07e3>] driver_probe_device+0x223/0x440
       [<ffffffff815c0ad5>] __driver_attach+0xd5/0x100
       [<ffffffff815be386>] bus_for_each_dev+0x66/0xa0
       [<ffffffff815c002e>] driver_attach+0x1e/0x20
       [<ffffffff815bf9be>] bus_add_driver+0x1ee/0x280
       [<ffffffff815c1810>] driver_register+0x60/0xe0
       [<ffffffff814a1a10>] __pci_register_driver+0x60/0x70
       [<ffffffffa01a905b>] i915_init+0x5b/0x62 [i915]
       [<ffffffff8100042d>] do_one_initcall+0x3d/0x150
       [<ffffffff811a935b>] do_init_module+0x5f/0x1d9
       [<ffffffff81124416>] load_module+0x20e6/0x27e0
       [<ffffffff81124d63>] SYSC_finit_module+0xc3/0xf0
       [<ffffffff81124dae>] SyS_finit_module+0xe/0x10
       [<ffffffff819a83a9>] entry_SYSCALL_64_fastpath+0x1c/0xac

-> #0 (&dev->mode_config.mutex){+.+.+.}:
       [<ffffffff810df0ac>] __lock_acquire+0x10fc/0x1260
       [<ffffffff810df611>] lock_acquire+0xb1/0x200
       [<ffffffff819a3097>] mutex_lock_nested+0x67/0x3c0
       [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120
       [<ffffffff8158f79b>] drm_fb_helper_restore_fbdev_mode_unlocked+0x2b/0x80
       [<ffffffff8158f81d>] drm_fb_helper_set_par+0x2d/0x50
       [<ffffffffa0105f7a>] intel_fbdev_set_par+0x1a/0x60 [i915]
       [<ffffffff814c13c6>] fbcon_init+0x586/0x610
       [<ffffffff8154d16a>] visual_init+0xca/0x130
       [<ffffffff8154e611>] do_bind_con_driver+0x1c1/0x3a0
       [<ffffffff8154eaf6>] do_take_over_console+0x116/0x180
       [<ffffffff814bd3a7>] do_fbcon_takeover+0x57/0xb0
       [<ffffffff814c1e48>] fbcon_event_notify+0x658/0x750
       [<ffffffff810abcae>] notifier_call_chain+0x3e/0xb0
       [<ffffffff810ac1ad>] __blocking_notifier_call_chain+0x4d/0x70
       [<ffffffff810ac1e6>] blocking_notifier_call_chain+0x16/0x20
       [<ffffffff814c748b>] fb_notifier_call_chain+0x1b/0x20
       [<ffffffff814c86b1>] register_framebuffer+0x251/0x330
       [<ffffffff8158fa9f>] drm_fb_helper_initial_config+0x25f/0x3f0
       [<ffffffffa0106b48>] intel_fbdev_initial_config+0x18/0x30 [i915]
       [<ffffffff810adfd8>] async_run_entry_fn+0x48/0x150
       [<ffffffff810a3947>] process_one_work+0x1e7/0x750
       [<ffffffff810a3efb>] worker_thread+0x4b/0x4f0
       [<ffffffff810aad4f>] kthread+0xef/0x110
       [<ffffffff819a85ef>] ret_from_fork+0x1f/0x40

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock((fb_notifier_list).rwsem);
                               lock(&dev->mode_config.mutex);
                               lock((fb_notifier_list).rwsem);
  lock(&dev->mode_config.mutex);

 *** DEADLOCK ***

6 locks held by kworker/u8:0/6:
 #0:  ("events_unbound"){.+.+.+}, at: [<ffffffff810a38c9>] process_one_work+0x169/0x750
 #1:  ((&entry->work)){+.+.+.}, at: [<ffffffff810a38c9>] process_one_work+0x169/0x750
 #2:  (registration_lock){+.+.+.}, at: [<ffffffff814c8487>] register_framebuffer+0x27/0x330
 #3:  (console_lock){+.+.+.}, at: [<ffffffff814c86ce>] register_framebuffer+0x26e/0x330
 #4:  (&fb_info->lock){+.+.+.}, at: [<ffffffff814c78dd>] lock_fb_info+0x1d/0x40
 #5:  ((fb_notifier_list).rwsem){++++.+}, at: [<ffffffff810ac195>] __blocking_notifier_call_chain+0x35/0x70

stack backtrace:
CPU: 2 PID: 6 Comm: kworker/u8:0 Tainted: G           O    4.7.0-rc5+ #524
Hardware name: Intel Corp. Broxton P/NOTEBOOK, BIOS APLKRVPA.X64.0138.B33.1606250842 06/25/2016
Workqueue: events_unbound async_run_entry_fn
 0000000000000000 ffff8800758577f0 ffffffff814507a5 ffffffff828b9900
 ffffffff828b9900 ffff880075857830 ffffffff810dc6fa ffff880075857880
 ffff88007584d688 0000000000000005 0000000000000006 ffff88007584d6b0
Call Trace:
 [<ffffffff814507a5>] dump_stack+0x67/0x92
 [<ffffffff810dc6fa>] print_circular_bug+0x1aa/0x200
 [<ffffffff810df0ac>] __lock_acquire+0x10fc/0x1260
 [<ffffffff810df611>] lock_acquire+0xb1/0x200
 [<ffffffff815afde0>] ? drm_modeset_lock_all+0x40/0x120
 [<ffffffff815afde0>] ? drm_modeset_lock_all+0x40/0x120
 [<ffffffff819a3097>] mutex_lock_nested+0x67/0x3c0
 [<ffffffff815afde0>] ? drm_modeset_lock_all+0x40/0x120
 [<ffffffff810fa85f>] ? rcu_read_lock_sched_held+0x7f/0x90
 [<ffffffff81208218>] ? kmem_cache_alloc_trace+0x248/0x2b0
 [<ffffffff815afdc5>] ? drm_modeset_lock_all+0x25/0x120
 [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120
 [<ffffffff8158f79b>] drm_fb_helper_restore_fbdev_mode_unlocked+0x2b/0x80
 [<ffffffff8158f81d>] drm_fb_helper_set_par+0x2d/0x50
 [<ffffffffa0105f7a>] intel_fbdev_set_par+0x1a/0x60 [i915]
 [<ffffffff814c13c6>] fbcon_init+0x586/0x610
 [<ffffffff8154d16a>] visual_init+0xca/0x130
 [<ffffffff8154e611>] do_bind_con_driver+0x1c1/0x3a0
 [<ffffffff8154eaf6>] do_take_over_console+0x116/0x180
 [<ffffffff814bd3a7>] do_fbcon_takeover+0x57/0xb0
 [<ffffffff814c1e48>] fbcon_event_notify+0x658/0x750
 [<ffffffff810abcae>] notifier_call_chain+0x3e/0xb0
 [<ffffffff810ac1ad>] __blocking_notifier_call_chain+0x4d/0x70
 [<ffffffff810ac1e6>] blocking_notifier_call_chain+0x16/0x20
 [<ffffffff814c748b>] fb_notifier_call_chain+0x1b/0x20
 [<ffffffff814c86b1>] register_framebuffer+0x251/0x330
 [<ffffffff815b7e8d>] ? vga_switcheroo_client_fb_set+0x5d/0x70
 [<ffffffff8158fa9f>] drm_fb_helper_initial_config+0x25f/0x3f0
 [<ffffffffa0106b48>] intel_fbdev_initial_config+0x18/0x30 [i915]
 [<ffffffff810adfd8>] async_run_entry_fn+0x48/0x150
 [<ffffffff810a3947>] process_one_work+0x1e7/0x750
 [<ffffffff810a38c9>] ? process_one_work+0x169/0x750
 [<ffffffff810a3efb>] worker_thread+0x4b/0x4f0
 [<ffffffff810a3eb0>] ? process_one_work+0x750/0x750
 [<ffffffff810aad4f>] kthread+0xef/0x110
 [<ffffffff819a85ef>] ret_from_fork+0x1f/0x40
 [<ffffffff810aac60>] ? kthread_stop+0x2e0/0x2e0

v2: Rebase onto the right branch (hand-editing patches ftw) and add more
reporters.
Reported-by: NImre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-by: NJiri Kosina <jikos@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The conversion of the rcar-du driver from the I2C slave encoder to the
DRM bridge API left the HDMI encoder's bridge pointer NULL, preventing
the bridge from being handled automatically by the DRM core. Fix it.

Fixes: 1d926114 ("drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder")
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer.  Thus the pointer can point to const data.
However the attributes do not have to be a bitfield.  Instead unsigned
long will do fine:

1. This is just simpler.  Both in terms of reading the code and setting
   attributes.  Instead of initializing local attributes on the stack
   and passing pointer to it to dma_set_attr(), just set the bits.

2. It brings safeness and checking for const correctness because the
   attributes are passed by value.

Semantic patches for this change (at least most of them):

    virtual patch
    virtual context

    @r@
    identifier f, attrs;

    @@
    f(...,
    - struct dma_attrs *attrs
    + unsigned long attrs
    , ...)
    {
    ...
    }

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

and

    // Options: --all-includes
    virtual patch
    virtual context

    @r@
    identifier f, attrs;
    type t;

    @@
    t f(..., struct dma_attrs *attrs);

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.comSigned-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Acked-by: NRobin Murphy <robin.murphy@arm.com>
Acked-by: NHans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This clearly had never gotten tested, probably because you need a fairly
minimal configuration in order to disable DEBUG_FS (several other
options select it).

The dummy inline functions that were used for the no-DEBUG_FS case were
missing the argument names in the declarations.

Fixes: 1dac891c ("drm/i915: Register debugfs interface last")
Reported-and-tested-by: NJörg Otte <jrg.otte@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bspec says:
"Restriction : SRD must not be enabled when the PSR Setup time from DPCD
00071h is greater than the time for vertical blank minus one line."

Let's check for that and disallow PSR if we exceed the limit.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Add a small helper to parse the PSR setup time from the DPCD PSR
capabilities and return the value in microseconds.

v2: Don't waste so many bytes on the psr_setup_time_us[] table

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This should fix some unaligned access warnings. This is also likely to
fix non-descript issues on nv30/nv34 as a result of incorrect channel
setup.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96836Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Since "PCI: Add runtime PM support for PCIe ports", the parent PCIe port
can be runtime-suspended which disables power resources via ACPI. This
is incompatible with DSM, resulting in a GPU device which is still in D3
and locks up the kernel on resume (on a Clevo P651RA, GTX965M).

Mirror the behavior of Windows 8 and newer[1] (as observed via an AMLi
debugger trace) and stop using the DSM functions for D3cold when power
resources are available on the parent PCIe port.

pci_d3cold_disable() is not used because on some machines, the old DSM
method is broken. On a Lenovo T440p (GT 730M) memory and disk corruption
would occur, but that is fixed with this patch[2].

 [1]: https://msdn.microsoft.com/windows/hardware/drivers/bringup/firmware-requirements-for-d3cold
 [2]: https://github.com/Bumblebee-Project/bbswitch/issues/78#issuecomment-223549072

 v2: simply check directly for _PR3. Added affected machines.
 v3: fixed block comment coding style.
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NPeter Wu <peter@lekensteyn.nl>
Acked-by: Dave Airlie <airlied@redhat.com
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Do not unconditionally invoke function 0x1B without checking for its
availability, it leads to an infinite loop on some firmware.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=104791
Fixes: 5addcf0a ("nouveau: add runtime PM support (v0.9)")
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NPeter Wu <peter@lekensteyn.nl>
Acked-by: Dave Airlie <airlied@redhat.com
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Return the set of supported functions to the caller. No functional
changes.
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NPeter Wu <peter@lekensteyn.nl>
Acked-by: Dave Airlie <airlied@redhat.com
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Ensure that the returned set of supported DSM functions (MUX, Optimus)
match the ACPI handle that is set in nouveau_dsm_pci_probe.

As there are no machines with a MUX function on just one PCI device and
an Optimus on another, there should not be a functional impact. This
change however makes this implicit assumption more obvious.

Convert int to bool and rename has_dsm to has_mux while at it. Let the
caller set nouveau_dsm_priv.dhandle as needed.

 v2: pass dhandle to the caller.
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NPeter Wu <peter@lekensteyn.nl>
Acked-by: Dave Airlie <airlied@redhat.com
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The patch f045f459 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
tries to fix some out of memory accesses. Unfortunatelly, the patch breaks the
display when using fonts with width that is not divisiable by 8.

The monochrome bitmap for each character is stored in memory by lines from top
to bottom. Each line is padded to a full byte.

For example, for 22x11 font, each line is padded to 16 bits, so each
character is consuming 44 bytes total, that is 11 32-bit words. The patch
f045f459 changed the logic to "dsize = ALIGN(image->width *
image->height, 32) >> 5", that is just 8 words - this is incorrect and it
causes display corruption.

This patch adds the necesary padding of lines to 8 bytes.

This patch should be backported to stable kernels where f045f459 was
backported.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Fixes: f045f459 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
Cc: stable@vger.kernel.org
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Setting PG state this early would cause lock ups in the IP block
initialized functions.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Cannot set clockgating state before ungating power.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch adds device id and revision into system info entry at CGS,
it's able to get PCI device id and revision id from amdgpu, it might
get more info in future.

PCI device id will be also used on powerplay part at current.
Suggested-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch adds new definition in bif header, and will be used on
iceland HW powertune part.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch renames the smum header guards to align with the file name.
Reported-by: NEdward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NKen Wang <Qingqing.Wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Supported starting on certain FW versions.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Context buffers should be denied by default, not allowed.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NSlava Grigorev <slava.grigorev@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Stoney support it, but doesn't has unlimited session support.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

we should give enough time to IB test.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NDavid Mao <David.Mao@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

run_job involves mutex, which could sleep.

V2: use list_for_each_entry_safe, since the job might complete
while we dropped the lock.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Means the hw ring is empty after gpu reset.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This will make sure all the submissions from different contexts gets
finished, and then we close the session and free up the handles.

This will fix the issue that session clean-up is not get done properly,
when with the command `kill -9'
Signed-off-by: NLeo Liu <leo.liu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We still need to unbind explicitly during a move.

This partial reverts commit ff20caa0bcbfef9f7686f8d1868a3b990921afd6.

v2: remove unnecessary check and unused variable
v3: fix typo in commit message
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NEdward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>