bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC
address. This is done differently for TLB and ALB modes.
bond->alb_info.rlb_enabled is used to discriminate between the two modes but
this flag may be uninitialized if the slave is being enslaved prior to calling
bond_open() -> bond_alb_initialize() on the master.

It turns out all the callers of alb_set_slave_mac_addr() pass
bond->alb_info.rlb_enabled as the hw parameter.

This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and
makes the function decide based on the bonding mode instead, which fixes the
above problem.
Reported-by: NNarendra K <Narendra_K@Dell.com>
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the MAC is invalid or not implemented, do not abort the probe. Issue
a warning and prevent bringing the interface up until a MAC is set manually
(via ifconfig $IFACE hw ether $MAC).

Tested on two platforms, one with a valid MAC, the other without a MAC. The real
MAC is used if present, the interface fails to come up until the MAC is set on
the other. They successfully get an IP over DHCP and pass a simple ping and
login over ssh test.

This is meant to allow the Inforce SYS940X development board:
http://www.inforcecomputing.com/SYS940X_ECX.html
(and others suffering from a missing MAC) to work with the mainline kernel.
Without this patch, the probe will fail and the interface will not be created,
preventing the user from configuring the MAC manually.

This does not make any attempt to address a missing or invalid MAC for the
pch_phub driver.
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
CC: Alan Cox <alan@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jon Mason <jdmason@kudzu.us>
CC: netdev@vger.kernel.org
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Joe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a race condition in addrconf_sysctl_forward() and
addrconf_sysctl_disable().
These functions change idev->cnf.forwarding (resp. idev->cnf.disable_ipv6)
and then try to grab the rtnl lock before performing any actions.
If that fails they restore the original value and restart the syscall.
This creates race conditions if ipv6 code tries to access
these parameters, or if multiple instances try to do the same operation.
As an example of the former, if __ipv6_ifa_notify() finds a 0 in
idev->cnf.forwarding when invoked by addrconf_ifdown() it may not free
anycast addresses, ultimately resulting in the net_device not being freed.
This patch reads the user parameters into a temporary location and only
writes the actual parameters when the rtnl lock is acquired.
Tested in 2.6.38.8.
Signed-off-by: NFrancesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vnic_dev_unregister is erroneously under CONFIG_PCI_IOV. This patch moves
it out of CONFIG_PCI_IOV
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch rearranges some of the port profile code in enic_probe.
It moves out some lines of port profile related code currently
inside CONFIG_PCI_IOV. This is only done to move all port profile
related code together so that it can help isolate the port profile
handling code under a separate #ifdef in our internal build scripts.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds checks for sriov vf's in enic port profile handling code.
sriov vf's are same as dynamic vnics but with a different device id.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds pci id 0x71 for sriov VF's.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Value must be a power of 2 due to HW limitation.
Driver supports only 'equal' mode in ethtool and can't be set by using weights.
Signed-off-by: NAmir Vadai <amirv@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several problems fixed in this patch :

1) Target of the conditional jump in case a divide by 0 is performed
   by a bpf is wrong.

2) Must 'generate' the full function prologue/epilogue at pass=0,
   or else we can stop too early in pass=1 if the proglen doesnt change.
   (if the increase of prologue/epilogue equals decrease of all
    instructions length because some jumps are converted to near jumps)

3) Change the wrong length detection at the end of code generation to
   issue a more explicit message, no need for a full stack trace.
Reported-by: NPhil Oester <kernel@linuxace.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When deauth is requested while an auth or assoc
work item is in progress, we currently delete it
without regard for any state it might need to
clean up. Fix it by cleaning up for those items.

In the case Pontus found, the problem manifested
itself as such:

authenticate with 00:23:69:aa:dd:7b (try 1)
authenticated
failed to insert Dummy STA entry for the AP (error -17)
deauthenticating from 00:23:69:aa:dd:7b by local choice (reason=2)

It could also happen differently if the driver
uses the tx_sync callback.

We can't just call the ->done() method of the work
items because that will lock up due to the locking
in cfg80211. This fix isn't very clean, but that
seems acceptable since I have patches pending to
remove this code completely.

Cc: stable@vger.kernel.org
Reported-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Tested-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use local->tx_headroom instad of local->hw.extra_tx_headroom.
local->tx_headroom is the max of hw.extra_tx_headroom required by the
driver and the headroom required by mac80211 for status reporting.  On
drivers where hw.extra_tx_headroom is smaller than what mac80211
requires (e.g. ath5k), we would not reserve sufficient buffer space to
report tx status.

Also, don't reserve local->tx_headroom + local->hw.extra_tx_headroom.
Reported-by: NSimon Morgenthaler <s.morgenthaler@students.unibe.ch>
Reported-by: NKai Scharwies <kai@scharwies.de>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch workaround live deadlock problem caused by infinite loop
in brcms_c_wait_for_tx_completion(). I do not consider the patch as
the proper fix, which should fix the real reason of tx queue flush
failure, but patch helps with system lockup.

Reference:
https://bugzilla.kernel.org/show_bug.cgi?id=42576Reported-and-tested-by: NPatrick <ragamuffin@datacomm.ch>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since stations moved into a virtual interface
subdirectory, this link has been broken. Fix it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
  tg3: Fix single-vector MSI-X code
  openvswitch: Fix multipart datapath dumps.
  ipv6: fix per device IP snmp counters
  inetpeer: initialize ->redirect_genid in inet_getpeer()
  net: fix NULL-deref in WARN() in skb_gso_segment()
  net: WARN if skb_checksum_help() is called on skb requiring segmentation
  caif: Remove bad WARN_ON in caif_dev
  caif: Fix typo in Vendor/Product-ID for CAIF modems
  bnx2x: Disable AN KR work-around for BCM57810
  bnx2x: Remove AutoGrEEEn for BCM84833
  bnx2x: Remove 100Mb force speed for BCM84833
  bnx2x: Fix PFC setting on BCM57840
  bnx2x: Fix Super-Isolate mode for BCM84833
  net: fix some sparse errors
  net: kill duplicate included header
  net: sh-eth: Fix build error by the value which is not defined
  net: Use device model to get driver name in skb_gso_segment()
  bridge: BH already disabled in br_fdb_cleanup()
  net: move sock_update_memcg outside of CONFIG_INET
  mwl8k: Fixing Sparse ENDIAN CHECK warning
  ...

Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled.  However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup.  When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.

This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt.  In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped.  This fixes the
problem.
Reported-by: NPaul Ingram <paul@nicira.com>
Signed-off-by: NBen Pfaff <blp@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 4ce3c183 (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.

percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ARM: fixes for ARM platforms

Some fallout from the 3.3. merge window as well as a couple bug fixes
for older preexisting bugs that seem valid to include at this time:

* sched_clock changes broke picoxcell, fix included
* BSYM bugs causing issues with thumb2-built kernels on SMP
* Missing module.h include on msm.
* A collection of bugfixes for samsung platforms that didn't make it into
  the first pull requests.

* tag 'arm-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: make BSYM macro assembly only
  ARM: highbank: remove incorrect BSYM usage
  ARM: imx: remove incorrect BSYM usage
  ARM: exynos: remove incorrect BSYM usage
  ARM: ux500: add missing ENDPROC to headsmp.S
  ARM: msm: Add missing ENDPROC to headsmp.S
  ARM: versatile: Add missing ENDPROC to headsmp.S
  ARM: EXYNOS: Invert VCLK polarity for framebuffer on ORIGEN
  ARM: S3C64XX: Fix interrupt configuration for PCA935x on Cragganmore
  ARM: S3C64XX: Fix the memory mapped GPIOs on Cragganmore
  ARM: S3C64XX: Remove hsmmc1 from Cragganmore
  ARM: S3C64XX: Remove unconditional power domain disables
  ARM: SAMSUNG: Declare struct platform_device in plat/s3c64xx-spi.h
  ARM: SAMSUNG: dma-ops.h needs mach/dma.h
  ARM: SAMSUNG: Guard against multiple inclusion of plat/dma.h
  ARM: picoxcell: fix sched_clock() cleanup fallout
  ARM: msm: vreg is a module and so needs module.h

* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
  ARM: mach-shmobile: specify CHCLR registers on SH7372
  dma: shdma: fix runtime PM: clear channel buffers on reset
  dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
  dmaengine/ste_dma40: clear LNK on channel startup
  dmaengine: intel_mid_dma: remove legacy pm interface
  ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
  dmaengine: intel_mid_dma: error path fix
  dmaengine: intel_mid_dma: locking and freeing fixes
  mtd: gpmi-nand: move to dma_transfer_direction
  mtd: fix compile error for gpmi-nand
  mmc: mxs-mmc: fix the dma_transfer_direction migration
  dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
  dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
  dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
  dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
  dma: mxs-dma: fix a typo in comment
  DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
  video i.MX IPU: Fix display connections
  i.MX IPU DMA: Fix wrong burstsize settings
  dmaengine/ste_dma40: allow fixed physical channel
  ...

Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}

The conflicts looked pretty trivial, but I'll ask people to verify them.

* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
  [libata] ata_piix: Add Toshiba Satellite Pro A120 to the quirks list due to broken suspend functionality.
  [libata] add DVRTD08A and DVR-215 to NOSETXFER device quirk list
  [libata] pata_bf54x: Support sg list in bmdma transfer.
  [libata] sata_fsl: fix the controller operating mode
  [libata] enable ata port async suspend

JONGMAN HEO reports:

  With current linus git (commit a25a2b84), I got following build error,

  arch/x86/kernel/vm86_32.c: In function 'do_sys_vm86':
  arch/x86/kernel/vm86_32.c:340: error: implicit declaration of function '__audit_syscall_exit'
  make[3]: *** [arch/x86/kernel/vm86_32.o] Error 1

OK, I can reproduce it (32bit allmodconfig with AUDIT=y, AUDITSYSCALL=n)

It's due to commit d7e7528b: "Audit: push audit success and retcode
into arch ptrace.h".
Reported-by: NJONGMAN HEO <jongman.heo@samsung.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

due to broken suspend functionality.
Signed-off-by: NBenjamin Larsson <benjamin@southpole.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

BF54x on-chip ATAPI controller allows maximum 0x1fffe bytes to be transfered
in one ATAPI transfer. So, set the max sg_tablesize to 4.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: NYutaka Ando <r46913@freescale.com>
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This saves devices suspend/resume time.

Tested system suspend/resume with SATA IDE/AHCI mode 3 times.
Below is the time took for devices suspend/resume.

SATA mode    vanilla-kernel           patched-kernel
---------    ---------------------    ---------------------
IDE          suspend: 0.744           suspend: 0.432
             (0.716, 0.768, 0.748)    (0.440, 0.428, 0.428)

             resume: 5.084            resume: 2.209
             (5.100, 5.064, 5.088)    (2.168, 2.232, 2.228)

AHCI:        suspend: 0.725           suspend: 0.449
             (0.740, 0.708, 0.728)    (0.456, 0.448, 0.444)

             resume: 2.556            resume: 1.896
             (2.604, 2.492, 2.572)    (1.932, 1.872, 1.884)
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  integrity: digital signature config option name change
  lib: Removed MPILIB, MPILIB_EXTRA, and SIGNATURE prompts
  lib: MPILIB Kconfig description update
  lib: digital signature dependency fix
  lib: digital signature config option name change
  encrypted-keys: fix rcu and sparse messages
  keys: fix trusted/encrypted keys sparse rcu_assign_pointer messages
  KEYS: Add missing smp_rmb() primitives to the keyring search code
  TOMOYO: Accept \000 as a valid character.
  security: update MAINTAINERS file with new git repo

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
  audit: no leading space in audit_log_d_path prefix
  audit: treat s_id as an untrusted string
  audit: fix signedness bug in audit_log_execve_info()
  audit: comparison on interprocess fields
  audit: implement all object interfield comparisons
  audit: allow interfield comparison between gid and ogid
  audit: complex interfield comparison helper
  audit: allow interfield comparison in audit rules
  Kernel: Audit Support For The ARM Platform
  audit: do not call audit_getname on error
  audit: only allow tasks to set their loginuid if it is -1
  audit: remove task argument to audit_set_loginuid
  audit: allow audit matching on inode gid
  audit: allow matching on obj_uid
  audit: remove audit_finish_fork as it can't be called
  audit: reject entry,always rules
  audit: inline audit_free to simplify the look of generic code
  audit: drop audit_set_macxattr as it doesn't do anything
  audit: inline checks for not needing to collect aux records
  audit: drop some potentially inadvisable likely notations
  ...

Use evil merge to fix up grammar mistakes in Kconfig file.

Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: cleanup xfs_file_aio_write
  xfs: always return with the iolock held from xfs_file_aio_write_checks
  xfs: remove the i_new_size field in struct xfs_inode
  xfs: remove the i_size field in struct xfs_inode
  xfs: replace i_pin_wait with a bit waitqueue
  xfs: replace i_flock with a sleeping bitlock
  xfs: make i_flags an unsigned long
  xfs: remove the if_ext_max field in struct xfs_ifork
  xfs: remove the unused dm_attrs structure
  xfs: cleanup xfs_iomap_eof_align_last_fsb
  xfs: remove xfs_itruncate_data

* 'btrfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  btrfs: take allocation of ->tree_root into open_ctree()
  btrfs: let ->s_fs_info point to fs_info, not root...
  btrfs: consolidate failure exits in btrfs_mount() a bit
  btrfs: make free_fs_info() call ->kill_sb() unconditional
  btrfs: merge free_fs_info() calls on fill_super failures
  btrfs: kill pointless reassignment of ->s_fs_info in btrfs_fill_super()
  btrfs: make open_ctree() return int
  btrfs: sanitizing ->fs_info, part 5
  btrfs: sanitizing ->fs_info, part 4
  btrfs: sanitizing ->fs_info, part 3
  btrfs: sanitizing ->fs_info, part 2
  btrfs: sanitizing ->fs_info, part 1
  btrfs: fix a deadlock in btrfs_scan_one_device()
  btrfs: fix mount/umount race
  btrfs: get ->kill_sb() of its own
  btrfs: preparation to fixing mount/umount race

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (62 commits)
  Btrfs: use larger system chunks
  Btrfs: add a delalloc mutex to inodes for delalloc reservations
  Btrfs: space leak tracepoints
  Btrfs: protect orphan block rsv with spin_lock
  Btrfs: add allocator tracepoints
  Btrfs: don't call btrfs_throttle in file write
  Btrfs: release space on error in page_mkwrite
  Btrfs: fix btrfsck error 400 when truncating a compressed
  Btrfs: do not use btrfs_end_transaction_throttle everywhere
  Btrfs: add balance progress reporting
  Btrfs: allow for resuming restriper after it was paused
  Btrfs: allow for canceling restriper
  Btrfs: allow for pausing restriper
  Btrfs: add skip_balance mount option
  Btrfs: recover balance on mount
  Btrfs: save balance parameters to disk
  Btrfs: soft profile changing mode (aka soft convert)
  Btrfs: implement online profile changing
  Btrfs: do not reduce profile in do_chunk_alloc()
  Btrfs: virtual address space subset filter
  ...

Fix up trivial conflict in fs/btrfs/ioctl.c due to the use of the new
mnt_drop_write_file() helper.

Similar to SIGNATURE, rename INTEGRITY_DIGSIG to INTEGRITY_SIGNATURE.
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

As modules are expected to select MPILIB, MPILIB_EXTRA, and SIGNATURE,
removed Kconfig prompts.
Requested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

It was reported that description of the MPILIB_EXTRA is confusing.
Indeed it was copy-paste typo. It is fixed here.
Reported-by: NValdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Randy Dunlap reported build break:

ERROR: "crypto_alloc_shash" [lib/digsig.ko] undefined!
ERROR: "crypto_shash_final" [lib/digsig.ko] undefined!
ERROR: "crypto_shash_update" [lib/digsig.ko] undefined!
ERROR: "crypto_destroy_tfm" [lib/digsig.ko] undefined!

Added CRYPTO dependency and selected SHA1 algorithm.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

It was reported that DIGSIG is confusing name for digital signature
module. It was suggested to rename DIGSIG to SIGNATURE.
Requested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Suggested-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Enabling CONFIG_PROVE_RCU and CONFIG_SPARSE_RCU_POINTER resulted in
"suspicious rcu_dereference_check() usage!" and "incompatible types
in comparison expression (different address spaces)" messages.

Access the masterkey directly when holding the rwsem.

Changelog v1:
- Use either rcu_read_lock()/rcu_derefence_key()/rcu_read_unlock()
or remove the unnecessary rcu_derefence() - David Howells
Reported-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Define rcu_assign_keypointer(), which uses the key payload.rcudata instead
of payload.data, to resolve the CONFIG_SPARSE_RCU_POINTER message:
"incompatible types in comparison expression (different address spaces)"

Replace the rcu_assign_pointer() calls in encrypted/trusted keys with
rcu_assign_keypointer().
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>