Implement the port_pvid_get and vlan_getnext driver functions required
to dump VLAN entries from the hardware, with the VTU Get Next operation.

Some functions and structure will be shared with STU operations, since
their table format are similar (e.g. STU data entries are accessible
with the same registers as VTU entries, except with an offset of 2).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the VTU Flush operation (which also flushes the STU), so that
warm boots won't preserved old entries.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle TRACE_PKT, stack can sniff them on the first port
Add debubfs enrty to configure tracing for offload traffic like iWARP
& iSCSI for debugging purpose.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HWM_REVERSE() macro is unused, remove it.
Signed-off-by: Nyalin wang <yalin.wang2010@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rocker driver tracks arp_tbl neighs to resolve IPv4 route nexthops.  The
driver uses NETEVENT_NEIGH_UPDATE for neigh adds and updates, but there is
no event when the neigh is removed from the device (such as when the device
goes admin down).  This patches hooks ndo_neigh_destroy so the driver can
know when a neigh is removed from the device.  In response, the driver will
purge the neigh entry from its internal tbl.

I didn't find an in-tree users of ndo_neigh_destroy, so I'm not sure if
this ndo is vestigial or if there are out-of-tree users.  In any case, it
does what I need here.  An alternative design would be to generate
NETEVENT_NEIGH_UPDATE event when neigh is being destroyed, setting state to
NUD_NONE so driver knows neigh entry is dead.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On sucessful probe, driver prints the switch ID.  This patch changes the
format of the printed ID to match what's used in sysfs phys_switch_id node.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ACPI bindings for the smsc911x driver. Convert the DT specific calls
to nonspecific device* calls, This allows the driver to work
with both ACPI and DT configurations. Ethernet should now work when using
ACPI on ARM Juno.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Reviewed-by: NGraeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OF has some helper functions for parsing MAC and PHY settings.
In cases where the platform is providing this information rather
than the device itself, there needs to be similar functions for ACPI.

These functions are slightly modified versions of the ones in
of_net which can use information provided via DT or ACPI.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.

[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdfSigned-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit

  de3910eb ("edac: change the mem allocation scheme to
		 make Documentation/kobject.txt happy")

changed the memory allocation for the csrows member. But ppc4xx_edac was
forgotten in the patch. Fix it.
Signed-off-by: NMichael Walle <michael@walle.cc>
Cc: <stable@vger.kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Link: http://lkml.kernel.org/r/1437469253-8611-1-git-send-email-michael@walle.ccSigned-off-by: NBorislav Petkov <bp@suse.de>

If register_hdlc_device() fails, the current code returns 0 but we
should return an error code instead.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.

Just do a simple negative test instead.

The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add debugfs support to dump tid info like stid, sftid, tids, atid and
hwtids
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For T4 adapter, offloaded servers tid for IPv4 connections are
allocated from filter region. So add a new field for server filter tid if
server tid is allocated from filter region.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the tid info, differentiate from which region the TID is allocated
from. It can be from TCAM region or HASH region.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding more details to sge qinfo for debugging purpose.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This BQL implementation is mostly derived from its related driver, alx.
Tested on AR8131 (rev c0) [1969:1063]. Saturated a 100mbps link with 5
concurrent runs of netperf. Ping latency dropped from 14ms to 3ms.
Signed-off-by: NRon Angeles <ronangeles@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current filer rule optimization is broken in several ways:
 (1) Can perform reads/writes beyond end of allocated tables.
     (gianfar_ethtool.c:1326).

(2) It breaks badly for rules with more than 2 specifiers
     (e.g. matching ip, port, tos).

Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND         Q:00           ctrl:00000080 prop:00000210
01: FPR  == 00000210 AND CLE     Q:00           ctrl:00000281 prop:00000210
02: MASK == ffffffff AND         Q:00           ctrl:00000080 prop:ffffffff
03: DPT  == 00000003 AND         Q:00           ctrl:0000008e prop:00000003
04: TOS  == 00000003 AND         Q:00           ctrl:0000008a prop:00000003
05: DIA  == 0a000003 AND         Q:11           ctrl:0000448c prop:0a000003
06: DPT  == 00000002 AND         Q:00           ctrl:0000008e prop:00000002
07: TOS  == 00000002 AND         Q:00           ctrl:0000008a prop:00000002
08: DIA  == 0a000002 AND         Q:09           ctrl:0000248c prop:0a000002
09: DIA  == 0a000001 AND         Q:00           ctrl:0000008c prop:0a000001
0a: DPT  == 00000001 AND         Q:00           ctrl:0000008e prop:00000001
0b: TOS  == 00000001     CLE     Q:01           ctrl:0000060a prop:00000001
ff: MASK >= 00000000             Q:00           ctrl:00000020 prop:00000000

(Entire cluster gets AND-ed together).

 (3) We observed that the masking rules it generates do not
     play well with clustering on P2020.  Only first rule
     of the cluster would ever fire.  Given that optimizer
     relies heavily on masking this is very hard to fix.

Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1  action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2  action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3  action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND         Q:00           ctrl:00000080 prop:00000210
01: FPR  == 00000210 AND CLE     Q:00           ctrl:00000281 prop:00000210
02: MASK == ffffffff AND         Q:00           ctrl:00000080 prop:ffffffff
03: DPT  == 00000003 AND         Q:00           ctrl:0000008e prop:00000003
04: DIA  == 0a000003             Q:11           ctrl:0000440c prop:0a000003
05: DPT  == 00000002 AND         Q:00           ctrl:0000008e prop:00000002
06: DIA  == 0a000002             Q:09           ctrl:0000240c prop:0a000002
07: DIA  == 0a000001 AND         Q:00           ctrl:0000008c prop:0a000001
08: DPT  == 00000001     CLE     Q:01           ctrl:0000060e prop:00000001
ff: MASK >= 00000000             Q:00           ctrl:00000020 prop:00000000

Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules.  We found no errata covering this.

The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: NAleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAX_FILER_IDX is the last usable index.  Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables the use of ethtool --set-channels devname combined N to
change the number of vRSS queues. Separate rx, tx, and other parameters
are not supported. The maximum is rsscap.num_recv_que. It passes the
given value to rndis_filter_device_add through the device_info->num_chn
field.

If the procedure fails, it attempts to recover to the prior state. If
the recovery fails, it logs an error and aborts.

Current num_chn is saved and restored when changing the MTU.
Signed-off-by: NAndrew Schwartzmeyer <andschwa@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Uses device_info->num_chn to pass user provided number of vRSS
queues (from ethtool --set-channels) to rndis_filter_device_add. If
nonzero and less than the maximum, set net_device->num_chn to the given
value; else default to prior algorithm.

Always initialize struct device_info to 0, otherwise not all its fields
are guaranteed to be 0, which is necessary when checking if num_chn has
been purposefully set.
Signed-off-by: NAndrew Schwartzmeyer <andschwa@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing BUG_ON()
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx.c:2282 tx_complete() warn: variable dereferenced before check 'skb' (see line 2249)
lan78xx.c:2885 lan78xx_bh() info: ignoring unreachable code.
lan78xx.c:3159 lan78xx_probe() info: ignoring unreachable code.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the first slave is added (such as during bootup) the first
gratuitous ARP gets dropped. We don't see this drop during a failover.
The packet gets dropped in qdisc (noop_enqueue).

The fix is to delay the sending of gratuitous ARPs till the bond dev's
carrier is present.

It can also be worked around by setting num_grat_arp to more than 1.
Signed-off-by: NVenkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime.  Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 78ad5cdd.
This commit breaks dpm and suspend/resume on CZ.

Signed-off-by: NBoyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

When creating dm-cache with the default policy, it will call
request_module("dm-cache-default") to register the default policy.
But the "dm-cache-default" alias was left referring to the MQ policy.
Fix this by moving the module alias to SMQ.

Fixes: bccab6a0 (dm cache: switch the "default" cache replacement policy from mq to smq)
Signed-off-by: NYi Zhang <yizhan@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down.  If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.

This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp).  And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

The device details and mapping trees were just being decremented
before.  Now btree_del() is called to do a deep delete.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.

We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds an ndm_state member to the switchdev_obj_fdb structure,
in order to support static FDB addresses.

Set Rocker ndm_state to NUD_REACHABLE.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a low level _mv88e6xxx_atu_getnext function for convenient access to
the hardware, and rework the FDB Get Next operation.

This will ease the future integration with VLAN IDs.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a mv88e6xxx_atu_entry structure and a low level function for the ATU
Load operation, and provide FDB add and delete wrappers functions.

This implementation handles the eventual trunk mapping. If the related
bit is set, then the ATU data register would contain the trunk ID, and
not the port vector.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the prototype of port_getnext to include a vid parameter.

This is necessary to introduce the support for VLAN.

Also rename the fdb_{add,del,getnext} function pointers to
port_fdb_{add,del,getnext} since they are specific to a given port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.

The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).

This patch changes the fid_mask for an fid_bitmap of 4096 bits.

>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define register GLOBAL_ATU_FID instead of the raw value 0x01.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>