These patches rework the pci code for the sh architecture.

Currently each board implements some kind of ioport to address mapping.
Some boards use generic_io_base others try passing addresses as io ports.
This is the first set of patches that try to unify the pci code as much
as possible to avoid duplicated code. This will in the end lead to fewer
lines board specific code and more generic code.

This patch makes sure a struct pci_channel pointer is passed along to
various pci functions such as pci_read_reg(), pci_write_reg(),
pci_fixup_pcic(), sh7751_pcic_init() and sh7780_pcic_init().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch makes sure ctrl_inN/outN are used instead of inN/outN for on chip
pci registers. Without this patch addresses may be adjusted using the value
in generic_io_base. This patch makes it possible to set generic_io_base and
have pci without reading and writing all over the place.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NKatsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

By default we don't have anything to fix up for the SH-4 PCIC, boards can
overload this as necessary.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the L-BOX RE2 router.

	http://www.nttcom.co.jp/l-box/

L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.

The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Neither of these have had any maintenance in years, and there's
no interest in keeping them straggling along. These have already
been slated for removal some time, so finally just get rid of them.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix a problem uncovered by the recent change to always check the
arguments to pr_debug. The sh7751 was using the wrong name for the
PCI IO base address.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This cleans up quite a lot of the PCI mess that we
currently have, and attempts to consolidate the
duplication in the SH7780 and SH7751 PCI controllers.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the Renesas SH7780 development boards,
R7780RP and R7780MP.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!