The new function snd_hda_codec_amp_init() (and the stereo variant)
initializes the amp value only once at the first access.  If the amp
was already initialized or updated, this won't do anything more.

It's useful for initializing the input amps that are in the part of
the path but never used.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For optimizing the verb executions, a new mechanism to cache the verbs
and amp update commands is introduced.  With the new "write to cache
and flush" way, you can reduce the same verbs that have been written
multiple times.

When codec->cached_write flag is set, the further
snd_hda_codec_write_cache() and snd_hda_codec_amp_stereo() calls will
be performed only on the command or amp cache table, but not sent to
the hardware yet.  Once after you call all commands and update amps,
call snd_hda_codec_resume_amp() and snd_hda_codec_resume_cache().
Then all cached writes and amp updates will be written to the
hardware, and the dirty flags are cleared.

In this implementation, the existing cache table is reused, so
actually no big code change is seen here.  Each cache entry has a new
dirty flag now (so the cache key is now reduced to 31bit).

As a good side-effect by this change, snd_hda_codec_resume_*() will no
longer execute verbs that have been already issued during the resume
phase by checking the dirty flags.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The same type of code is being used in multiple places in various
codec drivers, so put it as a core library.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When both an SPDIF and an HDMI device are created on the same card
instance, multiple IEC958 controls are created with indices=0, 1, ...
But the alsa-lib configuration can't know which index corresponds
actually to which PCM device, and both the SPDIF and the HDMI
configurations point to the first IEC958 control wrongly.

This patch introduces a (hackish and ugly) workaround: the IEC958
controls for the SPDIF device are re-labeled with device=1 when HDMI
coexists.  The device=1 corresponds to the actual PCM device for
SPDIF, so it's anyway a better representation.  In future, HDMI
controls should be moved with the corresponding PCM device number,
too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

CONFIG_SND_HDA_POWER_SAVE is no longer an experimental feature and its
behavior can be well controlled via the default value and module
parameter.  Let's just replace it with the standard CONFIG_PM.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move snd_hda_mixer_amp_switch_put_beep() to hda_beep.c as a clean up
to remove one more ifdef.

Also add the corresponding get callback to return consistently the
digital beep state independently from the mixer amp value.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just code shuffles.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a new helper function to guess the default VREF pin control bits
for mic in.  This can be used to set the pin control value safely
matching with the actual pin capabilities.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For setting the pin-control values more safely to match with the
actual pin capability bits, a copule of new helper functions,
snd_hda_set_pin_ctl() and snd_hda_set_pin_ctl_cache(), are
introduced.  These are simple replacement of the codec verb write with
AC_VERB_SET_PIN_WIDGET but do more sanity checks and filter out
superfluous pin-control bits if they don't fit with the corresponding
pin capabilities.

Some codecs are screwed up or ignore the command when such a wrong bit
is set.  These helpers will avoid such secret errors.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since it's not always safe to assume that the vmaster hook is purely the
mute-LED control, add the flag indicating whether to expose the mute-LED
enum control or not.  Currently, conexant codec sets this off for non-HP
laptops where EAPD may be used really as EAPD.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Create snd_hda_add_vmaster_hook() and snd_hda_sync_vmaster_hook()
helper functions to handle the mute-LED in vmaster hook more
commonly.  In the former function, a new enum control "Mute-LED Mode"
is added.  This provides user to choose whether the mute-LED should be
turned on/off explicitly or to follow the master-mute status.
Reviewed-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It'll be used for adding hooks in later patches.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the driver is changed to use vmaster or a new slave element is
added by the improvement of the parser code, user may face often the
silent output because of the muted slave mixer although Master volume
is properly set.  And they complain.  And I get upset.

Although such a mixer element should be initialized via "alsactl init",
it'd be more user-friendly if the known output slaves are unmuted and
set to 0dB so that user can control the volume only with Master as
default.  Since Master is still set muted as default even with this
change, no risk of the speaker blow up, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In most cases, the slave strings for vmaster are identical between
volumes and switches except for "xxx Volume" and "xxx Switch" suffix.
Now snd_hda_add_vmaster() takes the optional suffix argument so that
each string can be composed with the given suffix, and we can share the
slave name strings in both volume and switch calls nicely.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When an invalid NID is given, get_wcaps() returns zero as the error,
but get_wcaps_type() takes it as the normal value and returns a bogus
AC_WID_AUD_OUT value.  This confuses the parser.

With this patch, get_wcaps_type() returns -1 when value 0 is given,
i.e. an invalid NID is passed to get_wcaps().

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740118

Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of managing input-jack stuff separately, call all stuff inside
the kctl-jack creation, deletion and report.  The caller no longer needs
to care about input-jack.

The better integration between input-jack and kctl-jack should be done
in the upper layer in near future, but for now, it's implemented locally
for more tests.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The function now gives more unique names for the output pins by adding
some prefix and suffix for the location and the channels.  Otherwise, it
can pass the index number.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We can use the very same table in hda_jack.c for managing the list for
input-jack elements, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Introduce a table containing the pins and their jack-detection states
for avoiding the unnecessary verbs to check the pin status at each time.

When the unsol event is enabled via snd_hda_jack_detect_enable(), it
automatically adds the given NID to the table.  Then the driver supposes
that the codec driver will set the dirty flag appropariately when an
unsolicited event is invoked for that pin.

The behavior for reading other pins that aren't registered in the table
doesn't change.  Only the pins assigned to the table are cached, so far.

In near futre, this table can be extended to use the central place for
the unsolicited events of all pins, etc, and eventually include the
jack-detect kcontrols that replace the current input-jack stuff.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Create a new helper function snd_hda_get_pin_label() for getting a label
string for both input and output pins.  hda_get_input_pin_label() is
obsoleted by this function, and the callers are replaced appropriately
now by this patch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

memset(eld) clears eld->proc_entry which will leak the struct
snd_info_entry when unloading module.

Fix it by
- memset only the fields before eld->eld_buffer
- set eld->eld_valid to true _after_ all eld fields have been filled

Cc: <stable@kernel.org>
Cc: Pierre-louis Bossart <pierre-louis.bossart@intel.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We disabled the check of NO_PRESENCE bit of the default pin-config
in commit f4419172 temporarily.  One problem was that the first
implementation was wrong -- the bit after the shift must be checked.
However, this would still give many regressions on machines with broken
BIOS.  They set this bit wrongly even on active pins.

A workaround is to check whether all pins contain this bit.  As far as
I've checked, broken BIOSen set this bit on all pins, no matter whether
active or not.  In such a case, the driver should ignore this bit check.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The implementation on commit [08a1f5eb: ALSA: hda - Check NO_PRESENCE
pincfg default bit] seems like a mis-interpretation of specification.
The spec gives the reversed bit definition.  But, following the spec
also causes to change so many existing device configurations, thus we
can't change it so easily for now.  For 3.2-rc1, it's safer to revert
this check (actually this patch comments out the code).

We may re-introduced the fixed version once after the wider test-case
coverages are done.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HD-audio spec defines a bit in pin default configuration for indicating
that the pin isn't used for jack-detection although the codec is capable
of it.  Better to check this bit as well in jack_is_detectable() helper
function.
Reported-by: NRaymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC260 has multiple mixer widgets connected to the shared DAC, but the
driver currently doesn't check this possibility and ignores when the DAC
is shared with others.  This resulted in the silent output from some
routes because of lack of the amp setup.

This patch adds the workaround for it by checking the route even with the
shared DAC, but also checking the conflict with the existing control for
the very same widget NID.

Reference: https://bugzilla.novell.com/show_bug.cgi?id=726812Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since hda_proc.c is now the only user of snd_print_pcm_rates(), better to
put it back locally to hda_proc.c and revert to the old style.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Applications may want to read ELD information to
understand what codecs are supported on the HDMI
receiver and handle the a-v delay for better lip-sync.

ELD information is exposed in a device-specific
IFACE_PCM kcontrol. Tested both with amixer and
PulseAudio; with a corresponding patch passthrough modes
are enabled automagically.

ELD control size is set to zero in case of errors or
wrong configurations. No notifications are implemented
for now, it is expected that jack detection is used to
reconfigure the audio outputs.
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For supporting both the multiple headphones and the multiple speakers,
add the new field in struct hda_multi_out, and evaluate in the standard
setup functions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... and add a new bit-flags argument to specify the behavior of the
function.  The older function is kept as is (as a wrapper).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It makes little sense to enable power-saving without PM.
This removes SND_HDA_NEEDS_RESUME define so that we can use CONFIG_PM
in all places.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

to fix build problems when it is disabled.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A future change won't store an entire hda_pcm_stream just to represent
the capabilities of a codec; a custom data-structure will be used. To
ease that transition, modify hdmi_eld_update_pcm_info to expect the
hda_pcm_stream to be pre-initialized with the codec's capabilities, and
to update those capabilities in-place based on the ELD.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The SPDIF output controls apply to converter widgets. A future change
will create a PCM device per pin widget, and hence a set of SPDIF output
controls per pin widget, for certain HDMI codecs. To support this, we
need the ability to virtualize the SPDIF output controls. Specifically:

* Controls can be "unassigned" from real hardware when a converter is
  not used for the PCM the control was created for.
* Control puts only write to hardware when they are assigned.
* Controls can be "assigned" to real hardware when a converter is picked
  to support output for a particular PCM.
* When a converter is assigned, the hardware is updated to the cached
  configuration.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also replace more open-codes with this function.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Implement the same functionality as Realtek's auto-mute mode control.
Now Conexant auto-parser can also mutes line-out and provide the enum
control for different automute behavior.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also fixed the assignment of multiout.dac_nids to satisfy const.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since multiple codec drivers already use the input-jack stuff, let's
make common helper functions to reduce the duplicated codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>