Currently, it isn't possible to request checksums on the outer UDP
header of tunnels - the TUNNEL_CSUM flag is ignored. This adds
support for requesting that UDP checksums be computed on transmit
and properly reported if they are present on receive.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFC: 3.20 first pull request

This is the first NFC pull request for 3.20.

With this one we have:

- Secure element support for the ST Micro st21nfca driver. This depends
  on a few HCI internal changes in order for example to support more
  than one secure element per controller.

- ACPI support for NXP's pn544 HCI driver. This controller is found on
  many x86 SoCs and is typically enumerated on the ACPI bus there.

- A few st21nfca and st21nfcb fixes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andy Shevchenko says:

====================
stmmac: Enable Intel Quark SoC X1000 Ethernet support

This is third version of the patch series [1] to bring network card support to
Intel Quark SoC.

The series has been tested on Intel Galileo board.

Changelog v3:
 - rebase on top of recent net-next
 - rework an approach to get the custom configuration
 - rework an approach how to get unique bus_id
 - improve DMI lookup function

[1] http://www.spinics.net/lists/netdev/msg296010.html
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Intel Quark SoC X1000, both of the Ethernet controllers support
MSI interrupt handling. This patch enables them to use MSI interrupt
servicing in stmmac_pci for Intel Quark X1000.
Signed-off-by: NKweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces run-time board detection through DMI and MAC-PHY
configuration function used by quark_default_data() during initialization. It
fills up the phy_addr for Galileo and Galileo Gen2 boards to indicate that the
Ethernet MAC controller is or is not connected to any PHY.

The implementation takes into consideration for future expansion in Quark
series boards that may have different PHY address that is linked to its MAC
controllers.

This piece of work is derived from Bryan O'Donoghue's initial work for Quark
X1000 enabling.
Signed-off-by: NKweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Intel Quark SoC X1000 provides two 10/100 Mbps Ethernet MAC
controllers which may or may not be connected to PHY on board.
This MAC controller only supports RMII PHY. This patch add Quark
PCI ID as well as Quark default platform data info to this driver.
Signed-off-by: NKweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently CPTS is built into the netcp driver even though there is no
call out to the CPTS driver. This patch removes the dependency in Kconfig
and remove cpts.o from the Makefile for NetCP.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move firmware version MACRO to a new t4fw_version.h file so that csiostor driver
can also use it.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix is to use default firmware configuration files
present in the adapter incase if not available in standard
/lib/firmware/* dir. Additional cleanup is done to reuse flash
related defines from cxgb4 header file.

Please apply over net-next since it depends on previous commit.
Signed-off-by: NPraveen Madhavan <praveenm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
Mellanox ethernet driver updates Jan-27-2015

This patchset introduces some bug fixes, code cleanups and support in a new
firmware event called recoverable error events.

Patches were applied and tested against commit b8665c6c ("net: dsa/mv88e6352:
make mv88e6352_wait generic")

Changes from V0:
- Patch 6/11 ("net/mlx4_core: Fix struct mlx4_vhcr_cmd to make implicit padding
  explicit"):
  - Removed __packed
  - Rephrased commit message

- Added a new patch by Majd ("net/mlx4_core: Update the HCA core clock frequency
  after INIT_PORT")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware might change the hca core clock frequency after the driver
issues the INIT_PORT command. Therefore we need to query the new
value again and save in to the cached dev caps.

Fixes: ddd8a6c1 ('net/mlx4_core: Read HCA frequency and map internal clock')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are dumping device capabilities which are supported both by the
firmware and the driver. Align the array that holds the capability
strings with this practice.
Reported-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a memory corruption at mlx4_MAD_IFC_wrapper.

A table of size dev->caps.pkey_table_len[port]*sizeof(*table)
was allocated, but get_full_pkey_table() assumes that the number
of entries in the table is a multiplication of 32 (which isn't always
correct).

Fixes: 0a9a0188 ('mlx4: MAD_IFC paravirtualization')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cmd->autoneg as a user hint to decide what to set in ethtool set settings callback.
When cmd->autoneg == AUTONEG_ENABLE set according to ethtool->advertise otherwise,
set according to ethtool->speed.

Usage:
	- ethtool -s eth<x> speed 56000 autoneg off
	- ethtool -s eth<x> advertise 0x800000 autoneg on

While we're here:
	- Move proto_admin masking outcome check to be adjacent to the operation.
	- Move en_warn("port reset..") print to "port reset" block.

Fixes: 312df74c ("net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set")
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm,
but not good practice.

Reported by the Mellanox Beijing team.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit
architectures.

This commit makes that padding explicit, to prevent issues with
changing compilers and with incompatibilities between 32-bit architecture
implicit padding and 64-bit architecture implicit padding.

This structure is used in virtualization for communication between
the Host and its Guests. The explicit padding allows 64-bit Hosts
(old and new) to continue to interoperate with 64-bit Guests (old and new).

However, without this fix, 64-bit Hosts could not interoperate with 32-bit
Guests (since these did not insert the padding dword). With this fix,
32-bit Guests will be able to interoperate with 64-bit Hosts (since
the structure offsets will be identical on both).
Reported-by: NAlexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware spec states that the timeout for all commands should be 60 seconds.

In the past, the spec indicated that there were several classes of timeout
(short, medium, and long).  The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.

In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Structs allocated for the resource tracker must be freed in
the error flow.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.

The reserved L_key value for a VF is:
    VF_lkey = base_lkey + (VF_number << 8).

This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.

To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.

When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous commit is based on a wrong assumption, fdb messages are always sent
into the netns where the interface stands (see vxlan_fdb_notify()).

These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we
need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example).

Note also that vxlan_nlmsg_size() was not updated.

Fixes: 193523bf ("vxlan: advertise netns of vxlan dev in fdb msg")
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jonathan Toppins says:

====================
bonding: various 802.3ad fixes

This patch series is a forward porting of patches we (Cumulus) are shipping
in our 3.2 series kernels. These fixes attempt to make 802.3ad bonding mode
more predictable in certian state machine transtions in addition to fixing
802.3ad bond carrier determination when bonding min_links option is changed.
Specific notes are contained within each patch.

For this patch series there are no userspace facing changes, a diff between
the modinfo output showed no difference. However, there are behavioral
facing changes, primarily in the bond carrier state. Please make sure to
review carefully.

v2:
 * fixed some style issues
 * dropped a portion of patch 1 in favor of more testing on my side
====================
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix sparse warning about non-static function

drivers/net/bonding/bond_main.c:3737:5: warning: symbol
'bond_3ad_xor_xmit' was not declared. Should it be static?
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a slave is added to a bond and it is not in full duplex mode,
AD_PORT_LACP_ENABLED flag is cleared, due to this LACP PDU is not sent
on slave. When the duplex is changed to full, the flag needs to be set
to send LACP PDU.

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch attempts to fix the following problems when an actor or
partner's aggregator is not active:
    1. a slave's lacp port state is marked as AD_STATE_SYNCHRONIZATION
       even if it is attached to an inactive aggregator. LACP advertises
       this state to the partner, making the partner think he can move
       into COLLECTING_DISTRIBUTING state even though this link will not
       pass traffic on the local side

    2. a slave goes into COLLECTING_DISTRIBUTING state without checking
       if the aggregator is actually active

    3. when in COLLECTING_DISTRIBUTING state, the partner parameters may
       change, e.g. the partner_oper_port_state.SYNCHRONIZATION. The
       local mux machine is not reacting to the change and continue to
       keep the slave and bond up

    4. When bond slave leaves an inactive aggregator and joins an active
       aggregator, the actor oper port state need to update to SYNC state.

v2:
 * fix style issues in bond_3ad.c

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NWilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mode 802.3ad, fix incorrect bond slave active state when slave is not in
active aggregator. During bond_open(), the bonding driver always sets
the slave active flag to true if the bond is not in active-backup, alb,
or tlb modes. Bonding should let the aggregator selection logic set the
active flag when in 802.3ad mode.

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NWilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

return type of wait_for_completion_timeout is unsigned long not int, this
patch just fixes up the declarations.
Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	arch/arm/boot/dts/imx6sx-sdb.dts
	net/sched/cls_bpf.c

Two simple sets of overlapping changes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is no support for ACPI.
This patch uses the following configuration:
	- Device id: NXP5440
	- Pin mapping:
		- 0 IRQ pin
		- 1 enable pin
		- 2 firmware pin
Signed-off-by: NRobert Dolca <robert.dolca@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

gpio_set_value was replaced with gpio_set_value_cansleep in order
to allow GPIO access that may sleep. This is particularelly useful
when GPIO is accessed using busses like I2C, SPI, USB
Signed-off-by: NRobert Dolca <robert.dolca@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On st21nfca, the mechanism to enable a secure element needs to add 2
properties in order manage the SWP line correctly.

Document ese-present and uicc-present properties.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

st21nfca has 1 physical SWP line and can support up to 2 secure elements
(UICC & eSE) thanks to an external switch managed with a gpio.

The platform integrator needs to specify thanks to 2 initialization
properties, uicc-present and ese-present, if it is suppose to have uicc
and/or ese. Of course if the platform does not have an external switch,
only one kind of secure element can be supported. Those parameters are
under platform integrator responsibilities.

During initialization, the white_list will be set according to those
parameters.

The discovery_se function will assume a secure element is physically
present according to uicc-present and ese-present values and will add it
to the secure element list. On ese activation, the atr is retrieved to
calculate a command exchange timeout based on the first atr(TB) value.

The se_io will allow to transfer data over SWP. 2 kind of events may appear
after a data is sent over:
- ST21NFCA_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCA_EVT_WTX_REQUEST when the secure element needs more time than
expected to compute a command. If this timeout expired, a first recovery
tentative consist to send a simple software reset proprietary command.
If this tentative still fail, a second recovery tentative consist to send
a hardware reset proprietary command.
This function is only relevant for eSE like secure element.

This patch also change the way a pipe is referenced. There can be
different pipe connected to the same gate with different host destination
(ex: CONNECTIVITY). In order to keep host information every pipe are
reference with a tuple (gate, host). In order to reduce changes, we are
keeping unchanged the way a gate is addressed on the Terminal Host.
However, this is working because we consider the apdu reader gate is only
present on the eSE slot also the connectivity gate cannot give a reliable
value; it will give the latest stored pipe value.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

With the newly introduced pipes table hci_dev fields,
the nfc_hci_pipe2gate routine is no longer needed.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The below event_received hci handler has change the gate parameter to pipe.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>

The below event_received hci handler has change the gate parameter to pipe.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>

When a command is received, it is sometime needed to let the CLF driver do
some additional operations. (ex: count remaining pipe notification...)
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We update the tracked pipes status when receiving HCI commands.
Also we forward HCI errors and we reply to any HCI command, even though
we don't support it.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>